Duracell 854-1707-07 User manual

975-0354-01-01 Revision 20100308
INSTANT JUMPSTART SYSTE
M
Introduction
Thank you for purchasing the Duracell® Instant Jumpstart System.
This product is part of a family of advanced personal renewable
energy devices from Battery-Biz Inc.
This Instant Jumpstart System is designed to revive weak car
batteries andjumpstart your vehicle, or provide emergency back-up
12 V DC power.
The Instant Jumpstart System is intended for use on 4 and 6 cylinder
gasoline powered cars and light trucks. Do not use on 6 V or 24 V
electrical systems vehicles. This Instant Jumpstart System is
designed to work if the vehicle's starter clicks or the engine turns
over too slowly to start. This product is not designed to start a vehicle
with a heavily discharged battery or for use on vehicle batteries that
are shorted or sulfated; they will not hold a charge and will need to be
replaced. See a professional technician.
Other uses for the Instant Jumpstart System include:
•backup power for equipment such as cell phones, PDAs,
notebooks, digital cameras, and other small portable devices,
•emergency light.
Important: The Instant Jumpstart System leaves the factory charged,
but due to battery self-discharge, it is recommended to charge it
immediately. This may take up to 48 hours. Recharge after every use
and every month if not used to protect the internal battery.
Important Safety Information
READ THIS GUIDE before operating the Instant Jumpstart
System, and SAVE IT FOR FUTURE REFERENCE.
Misusing or incorrectly connecting the Instant Jumpstart System may
damage the equipment or create hazardous conditions for users. Read
the following safety instructions and pay special attention to all
Caution and Warning statements in the guide.
Warnings identify conditions that may result in personal injury or
loss of life.
Cautions identify conditions or practices that may damage the unit or
other equipment.
Failure to follow these safety guidelines may cause personal injury
and/or damage to the Instant Jumpstart System. It may also void your
product warranty.
Features
Instant Jumpstart System Operation
Choosing a Location
The Jumpstart should be operated only in a location that is:
Dry. Do not allow water or other liquids to drop or splash on
the Jumpstart.
Cool. Ambient air temperature should be between 0 and 40ºC
(32 and 104ºF)—the coolerthe better within this range.
Ventilated. Leave at least 2" (5 cm) clearance around the Jumpstart
for air flow. Ensure that the ventilation openings are not
obstructed.
Safe. Do not operate the unit in the same compartment as
batteries or in any compartment capable of storing
flammable liquids like gasoline.
Protected from battery gases.Do not operate the Jumpstart where it
will be exposed to battery gases. These gases are very
corrosive, and prolonged exposure will damage the
Jumpstart.
Using the Instant Jumpstart System for the First Time
Prior to jumpstarting a vehicle or operating your 12 V DC appliance,
ensure that the battery of the Instant Jumpstart System is fully
charged.
Note: Press and hold the Battery Level button to view the battery
charge status.
Note: If the battery level is low but has not been fully discharged,
recharging with the AC Charger may take up to 28 hours.
Recharging with the AC Charger
Note:The Instant Jumpstart System battery level LEDs are only
accurate when the Jumpstart has been disconnected from all
appliances and all charging sources for 15 minutes.
Note:When the battery is fully charged, all four LEDs will be lit. As
charge decreases, the number of lit LEDs will decrease. When only
one LED is lit, the unit is discharged.
Note:Recharging with the AC Charger is a true “plug-in-and-forget”
charging method. We recommend leaving the AC Charger connected
when the Instant Jumpstart System is not in use.
To recharge the Instant Jumpstart System:
1. Disconnect any 12 V DC appliances and turn the light OFF.
2. Plug the AC Charger into a standard AC wall outlet.
3. Insert the AC Charger cable end into the AC Charger Input Socket
(see Features).
The Battery Status LED changes from red to green when charging is
complete (about 28 hours if the battery is completely discharged).
Important: The 28-hour charging time for the Jumpstart assumes that
there is 120 V AC at the AC wall outlet. If the voltage is less than 120
V AC, it may take more than 28 hours to fully recharge the Jumpstart.
If, after 28 hours of charging, the Battery Status LED remains red,
continue to charge the unit for another 12 hours. The unit will be
ready for use even if the Battery Status LED remains red.
Important: If you keep the Instant Jumpstart System in storage, the
battery will self-discharge over time. Remember to recharge the
batteryevery month to keep the Instant Jumpstart System
operational.
Note: Once fully charged, the charging current automatically reduces
to a maintenance charge mode, and the Jumpstart may be left
permanently connected to the AC Charger.
Using the Flashlight
The Instant Jumpstart System has an incandescent flashlight which
will operate for about 30 hours before the unit needs to be recharged.
The On/Off switch is located above the light (see Features).
Operating 12 V DC Appliances
The Instant Jumpstart System can operate as a 12 V DC power source
to portable appliances that draw 15 A or less from a 12 V DC power
outlet.
.
Note: The fewer watts a 12 V DC appliance draws, the longer the
Instant Jumpstart System will operate before recharging is required.
The table below lists typical 12 V appliances that can be used with
the Instant Jumpstart System.
a) Represents actual power consumption as measured on sample appliances.
b) Operating times assume a fully charged 17 Ah battery and may vary based
on model or brand of appliance.
c) Represents talk time available from 5 recharge cycles.
To operate a 12 V DC appliance:
1. Open the protective cover on the DC Power Outlet of the Instant
Jumpstart System.
2. Plug the 12 V DC appliance into the DC Power Outlet and turn
the 12 V DC appliance on (if required).
If the 12 V DC appliance draws more than 15 A (or has a short-
circuit defect), the 15 A external fuse will blow. If this occurs,
unplug the 12 V DC appliance and replace the fuse with a new
15 A fuse.
3. Fully recharge the Instant Jumpstart System as soon as possible
after each use. As the DC Power Outlet is internally wired directly
to the unit’s battery, extended operation of a 12 V DC appliance
may result in excessive battery discharge.
Jumpstarting a Vehicle’s Engine
You can use the Instant Jumpstart System to jumpstart a vehicle or
boat engine (most 4 cyl. and 6 cyl.) that has a 12 V starting battery
using the supplied jumpstart cables.
Important:Closely follow the succeeding instructions including
warnings for jumpstarting your vehicle as they may be different from
the instructions supplied with other jumpstarting products or
jumpstarting cables.
To jumpstart a vehicle:
1. Turn off the vehicle or boat ignition and all accessories.
2. Engage the park or emergency brake and place the transmission in
park for an automatic or neutral for a manual.
Note: Many vehicles with manual transmissions require that the
gear is set to neutral and that the clutch is fully in before starting.
3. If jumpstarting a boat engine, purge the engine compartment and
bilge of all fumes before jumpstarting.
4. Position the Instant Jumpstart System on a flat, stable surface near
the battery and away from all moving parts of the engine.
Important:Ensure that the Power Switch is OFF.
5. Connect the red positive (+) clip of the cables to the positive (+)
terminal of the engine battery.
The battery’s positive terminal is usually larger in diameter than
the negative terminal. In most vehicles, the battery’s positive
terminal has a red wire connected to it.
6. Connect the blacknegative (–) clip of the cables to the engine
block, cylinder head, or other stationary heavy metal part of the
motor.
If the red Instant Jumpstart System Connection LED illuminates
and sounds an alarm, then reverse polarity has been detected.
Correct polarity must be established before proceeding.
Disconnect the jumpstart clips from the vehicle’s battery and redo
steps 5 and 6 in this procedure.
If the Green Instant Jumpstart System Connection LED is
illuminated, then proceed to the next step.
7. Switch ON the Instant Jumpstart System Power Switch.
Before starting the engine, make sure the Instant Jumpstart
System and the cables are clear of belts and fans.
8. Crank the engine for 4 seconds or until it starts, whichever is first.
9. Switch OFF the Instant Jumpstart System Power Switch.
10.Remove the red positive (+) clip and then the black negative (–)
clip from the vehicle.
11.Store the jumpstart clips in the appropriate holder on each side of
the Instant Jumpstart System.
Important:Recharge the Instant Jumpstart System as soon as
possible after each use.
Connecting to an External Battery
You can extend battery operating times of DC appliances connected
to the socket by connecting the Jumpstart to a larger external battery.
For example, an external 60 Ah battery gives approximately four
times the operating time of the Jumpstart internal 17 Ah battery.
Important: See the WARNING statements from “Jumpstarting a
Vehicle’s Engine”
To connect the Instant Jumpstart System to an external battery
using the jumpstart clips:
1. Ensure that the Instant Jumpstart System Power Switch is OFF.
2. Connect the red positive (+) clip of the cables to the red positive
(+) terminal of the external battery.
3. Connect the blacknegative (–) clip of the cables to the black
negative (–) terminal of the external battery.
If the red Instant Jumpstart System Connection LED illuminates
and sounds an alarm, then reverse polarity has been detected.
Correct polarity must be established before proceeding.
WARNING
Keep the Instant Jumpstart System out of reach of children and pets.
Operate the unit with care!
WARNING
Do not insert any object into the Instant Jumpstart System’s ports or
openings.
WARNING
Do not expose this product to water, rain, snow, or spray.
WARNING
Use only the supplied AC charger adapter and the 12 V DC vehicle
jumpstart plug and cable to charge the Instant Jumpstart System.
WARNING
The Instant Jumpstart System’s internal battery is a sealed, AGM
lead-acid type battery. Although the battery is sealed, do not use the
Instant Jumpstart System if the casing is broken or if it emits an
unusual odor, produces excessive heat, or leaks. Avoid contact with
any substance that leaks from the Instant Jumpstart System.
WARNING
Do not attempt to open and disassemble the Instant Jumpstart
System, there are no user-serviceable parts inside.
CAUTION
Do not use the Instant Jumpstart System in ambient temperatures
over 104° F (40° C).
CAUTION
Do not store the Instant Jumpstart System in ambient temperatures
over 104° F (40° C).
Feature Description
1Battery Level LEDs illuminate to indicate the Instant
Jumpstart System battery charge level. All LEDs (two
green, one yellow and one red) are illuminated when the
battery is fully charged (Full), only the red LED is
illuminated when the battery is completely discharged
(Empty).
2Battery Level button triggers the Battery Level Full/
Empty LED indicators. Press and hold to view the
battery charge status.
3AC Charger Input Socket
4Light Switch
5Incandescent Light illuminates for about 30 hours
when the battery is fully charged.
6DC Power Outlet:
Powers 12 V DC appliances
Recharges Instant Jumpstart System from a 12 V outlet
in a vehicle using the DC Charging Cable.
7Green Jumpstart Connection LED illuminates when
the jumpstart clips are properly connected to the vehicle
battery.
8Red Jumpstart ConnectionLED illuminates when the
jumpstart clips are improperly connected (reversed
polarity) to the vehicle battery. An audible alarm also
sounds when the jumpstart clips are improperly
connected.
9Battery Status green LED illuminates when the Instant
Jumpstart System is Charged
(i.e.,anAC Charger is connected to the Instant
Jumpstart System’s AC Charger Input Socket and
plugged into the household 120 V AC wall outlet).
CAUTION
Do not use the Instant Jumpstart System to operate any 12 V DC
appliances while recharging with the AC Charger.
The AC Charger may fail if 12 V DC appliances are operated while
the AC Charger is connected.
1
2
3
4
5
6
7
8
9
Feature Description
1Jumpstart Power Switch
215A fuse for the 12 VDC power outlet
3Jumpstart Clips
4DC Charging Cable (Part no. 448-0156-01-01) lets you
recharge the Instant Jumpstart System from a 12 V
system in a car, SUV, RV or a boat.
5AC Charger (Part no. 074-1019-04) lets you recharge
the Instant Jumpstart System from a standard AC wall
outlet and can only be used to recharge the internal
battery of the Instant Jumpstart System.
WARNING
The Jumpstart contains components that tend to produce arcs or
sparks. To prevent fire or explosion, do not operate the Jumpstart in
compartments containing batteries or flammable materials, or in
locations that require ignition-protected equipment.
1
3
5
2
4
WARNING
Do not cover the Instant Jumpstart System while the flashlight is on
with any material such as a blanket. Doing so may cause heat from
the bulb to build up and eventually melt the plastic cover.
CAUTION
The DC Power Outlet does not automatically switch off when the
internal battery is discharged. To protect the internal battery against
damage resulting from total discharge, we recommend to unplug the
DC plug from the DC Power Outlet after use.
12 V DC Appliance WattsaHoursb
Cellular telephonec6 25
Portable vacuum cleaner 100 1
Portable cooler 30 5
WARNING
Never allow jumpstarting cables’ red and black clips to touch
each other or another common metal conductor. This could
cause damage to the unit and/or create a sparking/explosion
hazard. Always switch OFF the Power Switch and store
jumpstart clips in the appropriate holder on each side of the
Instant Jumpstart System after use.
WARNING
The Instant Jumpstart System’s cable clips’ connection to the
vehicle’s battery terminals must be positive to positive (red clip
to battery “+”) and negative to negative (black clip to battery “–”
or to engine block). A reverse polarity connection (positive to
negative) may cause damage to the unit and/or create a
sparking/explosion hazard.
CAUTION
Do not crank the engine for more than 4 seconds. The jumpstarting
feature is designed for short term operation only. Operating the
jumpstarting feature for more than 4 seconds may cause damage to
the unit. Allow the Instant Jumpstart System to cool down for at least
3 minutes after each jumpstart.
:ENERGY HAZARD.
:ENERGY HAZARD.
:ENERGY HAZARD.
:ENERGY, FIRE HAZARD.
:CHEMICAL, FIRE HAZARD.
:ENERGY, CHEMICAL HAZARD.
:EQUIPMENT DAMAGE.
:EQUIPMENT DAMAGE.:EQUIPMENTDAMAGE.
:FIRE, EXPLOSION HAZARD.
:HEATHAZARD.
:EXPLOSIONHAZARD.
:EXPLOSIONHAZARD.
:INTERNALBATTERY DAMAGE.
:EQUIPMENT DAMAGE.

975-0354-01-01 Revision 2010308
INSTANT JUMPSTART SYSTE
M
Disconnect the jumpstart clips from the vehicle’s battery and redo
steps 2 and 3 in this procedure.
If no alarm sounds, and the Green Jumpstart Connection LED is
illuminated, then proceed to the next step.
4. Switch ON the Instant Jumpstart System Power Switch.
To disconnect the jumpstart clips from an external battery and
from the Instant Jumpstart System:
1. Ensure that the Jumpstart Power Switch is OFF.
2. Remove the red positive (+) clip, and then remove the black
negative (–) clip from the external battery terminals.
3. Store the jumpstart clips in the appropriate holder on each side of
the Jumpstart.
4. Recharge the Jumpstart as soon as possible after use.
Instant Jumpstart System Maintenance
Routine maintenance is required to keep your Jumpstart operating
properly. Occasionally clean the exterior of the unit with a damp cloth
to remove the accumulated dust and dirt.
Maintaining the Battery
All rechargeable batteries gradually discharge when left standing, and
you need to recharge them periodically to maintain maximum battery
capacity. The AC Charger supplied with the Jumpstart is designed to
regulate the charging process, ensuring that the battery is always fully
charged but never overcharged. To ensure safe recharging and
maximum battery life, recharge the Jumpstart only with the supplied
charger or approved battery chargers.
Recharging with the AC Charger
See “Recharging with the AC Charger” under “Instant Jumpstart
System Operation”.
Recharging Using the DC Charging Cable
Important:Although the charge regulation circuitry in the Jumpstart
does not operate with this charging method, most vehicle voltage
regulators will ensure that the Jumpstart is not overcharged.
1. While the vehicle engine is running, plug one end of the DC
Charging Cable into the DC Power Outlet of the Instant Jumpstart
System.
2. Plug the opposite end of the DC Charging Cable into the vehicle’s
lighter socket or 12 V accessory outlet.
3. Once the Instant Jumpstart System is fully charged or if your
vehicle’s engine is not running, disconnect the DC Charging Cable
from both sockets. Most of the Instant Jumpstart System’s capacity
will be restored in 2 ½ hours while the vehicleengine is running.
Note: The Battery Status LED will not illuminate when the Jumpstart
is recharged through the DC Charging Cable.
Important: Do not leave the Instant Jumpstart System permanently
connected to the vehicle’s lighter socket or 12 V accessory outlet.
Recharging with a Generator’s Regulated 12 V DC
Outlet
Refer to the Owner’s Guide accompanying your generator for detailed
instructions on connecting a 12V load, like the jumpstart, to your
generator.
You can recharge using a generator in several ways:
•Using the AC Charger to recharge the Jumpstart from a generator
is possible, but would require extended generator running time.
•Using a generator which has an auxiliary regulated 12 V DC
output designed for charging 12 V DC batteries. Most generators
are equipped with them. Use this power source for faster charging.
•Using a generator with a regulated 12 V DC lighter socket. Follow
the connection instructions in “Recharging Using the DC Charging
Cable”.
Recharging from a Solar Panel
Small, unregulated 12 V solar panels rated to produce a maximum of
2.5 A (or 30 W) can be used to charge the Jumpstart through the AC
Charger Input Socket. You will need to purchase a standard 5.5 mm
OD × 2.5 mm ID (0.217 × 0.10") coaxial DC (barrel type centre
positive) connector to mate with the AC Charger Input Socket. These
connectors are available at consumer electronics stores.
1. Connect the solar panel’s red positive (+) wire to the coaxial plug’s
inner or centre contact.
2. Connect the solar panel’s black negative(–) wire to theplug’s
outer contact.
Once the connector is inserted into the AC Charger Input Socket and
the solar panel is placed in the sun, the Jumpstart charges
automatically just as with the AC Charger. It takes about six hours in
direct sunlight to recharge the Jumpstart from a 2.5 A solar panel.
Replacing the Emergency Light Bulb
1. Turn the flashlight switch off.
2. Pop out the plastic lens cover.
3. Gently grasp the bulb and twist clockwise to unscrew the bulb.
Note: There’s a triangular notch at the neck of the bulb which
should align with the reflector assembly’s bulb socket collar.
4. Insert a replacement bulb of the same type and rating into the light
reflector assembly.
5. Gently grasp the bulb and twist counter-clockwise to screw the
bulb in.
6. Snap in the lens cover.
Recycling
If it’s rechargeable, it’s recyclable!
Battery-Biz is committed to environmental responsibility and has
established a program for recycling Duracell rechargeable
battery-related products.
For instructions on how to recycle this product visit www.rbrc.org
Troubleshooting
PROBLEM: Portable device or emergency light will not operate.
PROBLEM: Instant Jumpstart System will not jumpstart a vehicle.
PROBLEM: Instant Jumpstart System will not charge.
Specifications
Specifications are subject to change without notice.
Warranty and Return
CAUTION
Do not recharge the Instant Jumpstart System when an external
battery is connected. The AC charger may be damaged.
CAUTION
When charging for the first time, you must completely charge the
Instant Jumpstart System. This may take up to 48 hours.
If not used for a month, orwhen recharging after use, charging the
Instant Jumpstart System may take 4-5 hours with vehicle DC or up
to 28 hours with household AC.
WARNING
Disconnect all sources of AC power and DC power before
performing any type of maintenance.
CAUTION
Due to inherent self-discharge, lead acid batteries must be charged at
least every month, especially in a warm environment. Leaving a
battery in a discharged state, or not recharging every month, may
result in permanent battery damage and poor jumpstarting
performance.
CAUTION
Do not attempt to recharge the Instant Jumpstart System battery if it
is frozen. Gradually warm the frozen battery to 0°C (32°F) before
recharging.
WARNING
Do not use this recharging method if your vehicle has abnormally
high voltage electrical systems that operate above 15 V DC. This
may lead to accumulations of hydrogen, causing exposure to fire and
explosion hazard.
CAUTION
Do not operate DC appliances while the Jumpstart is being recharged
with the DC Charging Cable from your vehicle.
WARNING
The generator output must be intended for battery charging and have
an output of 15 V or less. An unregulated output or one that exceeds
15 V DC can damage the battery.
This may lead to accumulations of hydrogen, causing exposure to
fire and explosion hazard.
Possible cause Remedy
Portable device connected
has a high startup surge.
Portable device exceeds Instant
Jumpstart System surge capability, do
not use.
The Instant Jumpstart
System has overheated
due to poor ventilation.
Unplug all devices connected to the 12
V DC power supply socket and switch
off the flashlight. Allow the Instant
Jumpstart System to cool for 15
minutes. Remove objects covering the
Instant Jumpstart System. Move the
Instant Jumpstart System to a cooler
place.
Product(s) connected are
rated at more than the
Instant Jumpstart
System’s continuous
power rating.
Unplug the product that is causing the
overload. Check the 15 A fuse. If it is
blown or damaged, replace it with a
similarly rated fuse (15 A, 32 V). Use a
product with a power rating less than
the Instant Jumpstart System’s
continuous power rating.
Instant Jumpstart System
battery is completely
discharged.
Recharge Instant Jumpstart System.
Possible cause Remedy
Instant Jumpstart System
battery is completely
discharged.
Recharge Instant Jumpstart System.
Vehicle battery is heavily
discharged or sulfated.
Replace vehicle battery.
Vehicle has 6 V or 24 V
electrical system.
Instant Jumpstart System is not
designed to jumpstart these vehicles.
Possible cause Remedy
The input charging
voltage is out of range
(charger is defective).
Replace charger.
Vehicle battery is
completely discharged (if
recharging with vehicle
DC).
Recharge vehiclebattery.
12 V DC Section
Internal battery type Sealed, AGM (Absorbed
Glass Mat) lead-acid
Internal battery voltage (nominal) 12 V DC
Internal battery capacity (min.) 17 Ah
Internal battery current rating 170 CCA/400 CA
DC output current (max.) 15 A (fuse protected)
Replaceable Incandescent Bulb 12 V, 3–5 W
Internal Battery Charging
Charging current (nominal) 350 mA
Charging voltage (nominal) 13.8 V
AC Charger input socket
maximum current
2.5 A
Operating temperature range 0–40ºC (32–104ºF)
Storage temperature range 0–30ºC (32–86ºF)
Physical Specifications
Dimensions (L × W × H) 9 × 7 1/2 × 12 3/4 in.
(22.86 × 19.05 × 32.38 cm)
)gk5.6(bl4.41thgieW
Accessories
DC charge cable
(Part no. 448-0156-01-01)
30” (76 cm) 18 AWG with male to
male lighter plug
AC Charger
(Part no. 074-1019-04)
Input: 100-240 Vac, 50/60 Hz, 250 mA
Output:14.5 Vdc, 350 mA
AC Charger is faulty or
there is no power at the
AC wall outlet.
Replace the AC Charger or make sure
there is power available at the AC wall
outlet.
Possible cause Remedy
:EQUIPMENT DAMAGE.
:EQUIPMENT DAMAGE.
:INTERNAL BATTERYDAMAGE.
:INTERNAL BATTERYDAMAGE.
:ENERGY, SHOCKHAZARD.
:EQUIPMENT DAMAGE.
:ENERGY HAZARD.
:FIRE, EXPLOSIONHAZARD.
Quality Guarantee
Battery-Biz guarantees each Duracell® product to be free of defects
due to faulty materials or workmanship. This Duracell® product
carries a 1-year limited warranty from the date of purchase.
If found to be defective, this Duracell® product will be replaced
without charge when returned to Battery-Biz. This guarantee does not
apply to damage from misuse or abuse beyond normal usage. This
guarantee gives you specific legal rights, and you may also have other
rights which vary from state to state. Should any device be damaged
by this product due to defects in the product arising from faulty
materials or workmanship, Battery-Biz will repair or replace (at our
option) the device, provided both device and product usage instruc-
tions have been followed.
Send device with the product to:
Battery-Biz Inc.
1380 Flynn Road, Camarillo, CA 93012
Attention: Duracell Product Returns
If you would like additional information on Duracell products call
1-800-842-2127 or 1-805-437-7765 (7:30 AM-4:30 PM PST).
Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to
calling, please review the technical support tips below.
• Call from a phone where you have access to your mobile
device
• Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL® product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone
- U.S. and Canada [phone]
- Outside of the US/Canada: [phone]
Written inquires should be directed to:
Battery-Biz Inc.
DURACELL Product Inquiry
1380 Flynn Road,
Camarillo, CA 93012, USA
One Year Limited Warranty
This product carries a limited warranty against defects in material
and workmanship under normal use and service for one year from
the original date of purchase. The manufacturer or distributor, at its
option, shall repair or replace the defective unit covered by this
warranty. Please retain the dated sales receipt as evidence of the date
of purchase as it will be required for any warranty service. In order
to keep the warranty in effect, the product must have been handled
and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident,
misuse, abuse or negligence.
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the
extent permitted by law, the manufacturer and distributor disclaim all
other implied or express warranties including all warranties of
merchantability and/or fitness for any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as
expressly stated in the limited warranty described herein, the
manufacturer and distributor shall not be liable for any damages,
whether direct, indirect, incidental, special, consequential,
exemplary, or otherwise, including lost revenues, lost profits, loss of
use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims,
arising out of any theory of recovery, including statutory, contract or
tort. Not withstanding the term of any limited or implied warranty, or
in the event that any limited warranty fails of its essential purpose, in
no event will the manufacturer’s and distributor’s entire liability
exceed the purchase price of this product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequen-
tial damages so the above limitations or exclusions may not apply to
you. This limited warranty gives you specific legal rights. You may
have other rights which vary from state to state and province to
province.
©2010 Duracell. DURACELL® is a registered trademark of The Gillette Company, used
under license. All rights reserved. All logos and trademarks are used for identification
purposes only and may be trademarks or registered trademarks of their respective holders.