Duracell DRLJS110B User manual
1100 Amp Li-Ion Jump-Starter
(DRLJS110B/DRBTLC)
IMPORTANT: SAVE THESE INSTRUCTIONS
Misusing or incorrectly connecting the DURACELL®Jump-Starter may
damage the equipment or create hazardous conditions for users.
1. Download the PowerHub™app
The PowerHub™app enables advanced features:
• Battery monitoring and alerts
• Interactive step-by-step guide
• Live support
► Download the app to get started:
DuracellPower.com/App
Scan for app download
2. Product details
12
34
10 11
9
5 6
7 8
BLUETOOTH
1: Jump-start port
connects
to jump-start clamps.
2: USB port (2.4 Amps)
charges smartphones,
tablets and other devices.
3: Charging ‘IN’ port
connects to USB cable to
recharge the Jump-starter.
4: LED ashlight
features
high beam, low beam and
emergency/SOS mode.
5: Battery level button
and LED gauge
displays
battery charge level.
6: LED status light
bar
indicates state of the
Jump-Starter connection (see
Section 7).
7: Light button
activates the
LED ashlight.
8: Bluetooth button
Hold
3 seconds for pairing mode
(requires Duracell Power App).
9: Jump-start clamps
with SafeJump™ feature.
10: Carry bag ts into most
vehicle glove boxes.
11:
DC charger and USB
cable
for recharging the
Jump-Starter.
3. Charging the Jump-starter
WARNING: SHOCK HAZARD
Disconnect jump-start clamps before charging the Jump-starter.
CAUTION
Do not attempt to recharge the Jump-starter battery if it is frozen.
Gradually warm the frozen battery to 32 °F (0 °C) before recharging.
IMPORTANT: FULLY CHARGE BEFORE USE
Prior to using the Jump-starter for the rst time, ensure that the battery of
the Jump-starter is fully charged. If the battery has been fully discharged,
charging with a USB charger may take up to 4 hours.
IMPORTANT: PROPER CHARGER OUTPUT
For fastest possible recharging time, please be sure to use an AC or DC
charger with a rating of 2.0 Amps or higher. The charge times shown
assume the usage of a charger with a 2.0A or higher power rating.
CAUTION
The included DC charger is for charging only Li-Ion type rechargeable
batteries. Other types of batteries may burst causing personal injury or
damage.
A
B
C
►Charging/re-charging the Jump-Starter
Charging times: Partially discharged (or after using jump-starter) -
30-60 minutes; fully discharged jump-starter battery - up to 4 hours
Charging with the included DC charger:
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the DC charger into the included 12V vehicle socket (Fig. A) and
connect the small micro USB end of the included USB charging cable to
the ‘IN’ port. (Fig. B)
3. It is best to have the vehicle running while charging.
Charging with an AC charger (sold separately):
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the USB cable into your USB wall charger (Fig. C - wall charger
sold separately) and connect the small micro USB end of the included
USB charging cable to the ‘IN’ port (Fig. B).
IMPORTANT
If you keep the Jump-starter in storage, the battery will discharge over
time. Remember to recharge the battery after every use to make sure it is
ready when you need it, and at least once a year. Re-charging more often
will not harm the Jump-starter.
4. Checking the Jump-starter’s battery level
To check the battery’s charge level, press the battery level button on the Jump-
Starter. The LED fuel gauge will illuminate and display the current level of
available battery power. Four lights indicate a 100% charge.
IMPORTANT
Your Jump-starter will perform best when its battery is fully charged. If the
LED Fuel Gauge shows less than 100% charge, it is recommended to fully
recharge its battery (see Section 4: “Charging the Jump-starter” ).
5. Using the LED ashlight and USB port
►Using the LED light
The DURACELL® Jump-Starter has a built-in emergency light to provide a safe,
bright work light on the roadside and in other outdoor environments.
Press and release the light button to cycle through the 3 light modes. (High
beam, Low Beam and SOS)
►Using the USB port
The USB port provides up to 2.4 Amps of current to charge cell phones,
smartphones, tablets and other devices.
1. Open the protective cover over the USB port.
2. Connect your USB device (smartphone, tablet, etc.) to the USB port using
the USB cable supplied with your device.
3. Charging will automatically start.
6. Jump-starting a vehicle
You can use the DURACELL®Jump-Starter with the supplied jump-start clamps
to jump-start a vehicle or boat engine. The Jump-Starter is compatible with 12V
vehicles.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is
designed for short term operation only. Operating the jump-start feature for
more than 4 seconds may cause damage to the unit. Allow the Jump-starter
to cool down for at least 30 seconds after each jump-start.
► To jump-start a vehicle engine:
1. Connect the jump-start clamps to the Jump-Starter
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery
and the black (-) clamp to the negative (-) terminal on the vehicle battery
3. Verify that the Jump-Starter and clamps are clear of any moving engine parts.
4. Start your engine, Be sure to crank for no more than 4 seconds at a time
and allow for 30 seconds in between starting attempts.
5. After starting the vehicle remove the Jump-starter and recharge it.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
7. Jump-Start LED bar function
Jump-start LED bar Reason and suggestion
OFF No clamp cable connected
Green ash Clamp cable connected, ready to connect to vehicle
Green ash (still ashing after
5 seconds of connection to
battery)
1. Turn off all vehicle accessories and lights; wait 5-10
minutes before reconnecting and try again.
2. If still ashing, the car battery may be below 3V and is
unsafe to use with this jump-starter.
Solid Green Good voltage and polarity - ready to start
Solid Red and beeping
while connecting
Reverse polarity or short - recheck connections
Solid Red - OR - 4 Fuel Gauge
LEDs ashing - After extended
starting
Over temperature - wait for the unit to cool down and reset.
Solid Red + 1 or 2 LED
on fuel gauge
Low internal battery voltage, please fully charge the unit
OFF - after 10 minutes Timed-out for safety, press power button to reset or re-at-
tach red clamp
Green ash after vehicle starts Reverse charge protection - Vehicle started, remove the unit
8. Specications
Electrical specications
Charging Input Voltage/Current 5V/2.0A
DC Adapter Input Voltage 12V
DC Adapter Output Voltage/Current 5V / 2.1 A
Safety certications / efciency certications UL (cTUVus), CEC/BC, FCC
(DC charger: CE,FCC)
Physical specications
Length 7.66 in (19.45 cm)
Width 3.31 in (8.40 cm)
Height 1.40 in (3.55 cm)
Weight (product only) 1.47 lbs (490 g)
9. Important safety instructions
IMPORTANT: Please read these general usage-related warnings and cautions
thoroughly before using this Jump-starter.
WARNING: When using this product, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the
product is used near children.
• Do not insert ngers or foreign objects into the product.
• Do not use this product with any application of which it was not intended.
• Use of an attachment not recommended or sold by the manufacturer may
result in risk of re, electric shock or injury to persons.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life
support systems or any other medical devices.
TM
1100 Amp Li-Ion Jump-Starter
(DRLJS110B/DRBTLC)
IMPORTANT: SAVE THESE INSTRUCTIONS
Misusing or incorrectly connecting the DURACELL®Jump-Starter may
damage the equipment or create hazardous conditions for users.
1. Download the PowerHub™app
The PowerHub™app enables advanced features:
• Battery monitoring and alerts
• Interactive step-by-step guide
• Live support
► Download the app to get started:
DuracellPower.com/App
Scan for app download
2. Product details
12
34
10 11
9
5 6
7 8
BLUETOOTH
1: Jump-start port
connects
to jump-start clamps.
2: USB port (2.4 Amps)
charges smartphones,
tablets and other devices.
3: Charging ‘IN’ port
connects to USB cable to
recharge the Jump-starter.
4: LED ashlight
features
high beam, low beam and
emergency/SOS mode.
5: Battery level button
and LED gauge
displays
battery charge level.
6: LED status light
bar
indicates state of the
Jump-Starter connection (see
Section 7).
7: Light button
activates the
LED ashlight.
8: Bluetooth button
Hold
3 seconds for pairing mode
(requires Duracell Power App).
9: Jump-start clamps
with SafeJump™ feature.
10: Carry bag ts into most
vehicle glove boxes.
11:
DC charger and USB
cable
for recharging the
Jump-Starter.
3. Charging the Jump-starter
WARNING: SHOCK HAZARD
Disconnect jump-start clamps before charging the Jump-starter.
CAUTION
Do not attempt to recharge the Jump-starter battery if it is frozen.
Gradually warm the frozen battery to 32 °F (0 °C) before recharging.
IMPORTANT: FULLY CHARGE BEFORE USE
Prior to using the Jump-starter for the rst time, ensure that the battery of
the Jump-starter is fully charged. If the battery has been fully discharged,
charging with a USB charger may take up to 4 hours.
IMPORTANT: PROPER CHARGER OUTPUT
For fastest possible recharging time, please be sure to use an AC or DC
charger with a rating of 2.0 Amps or higher. The charge times shown
assume the usage of a charger with a 2.0A or higher power rating.
CAUTION
The included DC charger is for charging only Li-Ion type rechargeable
batteries. Other types of batteries may burst causing personal injury or
damage.
A
B
C
►Charging/re-charging the Jump-Starter
Charging times: Partially discharged (or after using jump-starter) -
30-60 minutes; fully discharged jump-starter battery - up to 4 hours
Charging with the included DC charger:
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the DC charger into the included 12V vehicle socket (Fig. A) and
connect the small micro USB end of the included USB charging cable to
the ‘IN’ port. (Fig. B)
3. It is best to have the vehicle running while charging.
Charging with an AC charger (sold separately):
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the USB cable into your USB wall charger (Fig. C - wall charger
sold separately) and connect the small micro USB end of the included
USB charging cable to the ‘IN’ port (Fig. B).
IMPORTANT
If you keep the Jump-starter in storage, the battery will discharge over
time. Remember to recharge the battery after every use to make sure it is
ready when you need it, and at least once a year. Re-charging more often
will not harm the Jump-starter.
4. Checking the Jump-starter’s battery level
To check the battery’s charge level, press the battery level button on the Jump-
Starter. The LED fuel gauge will illuminate and display the current level of
available battery power. Four lights indicate a 100% charge.
IMPORTANT
Your Jump-starter will perform best when its battery is fully charged. If the
LED Fuel Gauge shows less than 100% charge, it is recommended to fully
recharge its battery (see Section 4: “Charging the Jump-starter” ).
5. Using the LED ashlight and USB port
►Using the LED light
The DURACELL® Jump-Starter has a built-in emergency light to provide a safe,
bright work light on the roadside and in other outdoor environments.
Press and release the light button to cycle through the 3 light modes. (High
beam, Low Beam and SOS)
►Using the USB port
The USB port provides up to 2.4 Amps of current to charge cell phones,
smartphones, tablets and other devices.
1. Open the protective cover over the USB port.
2. Connect your USB device (smartphone, tablet, etc.) to the USB port using
the USB cable supplied with your device.
3. Charging will automatically start.
6. Jump-starting a vehicle
You can use the DURACELL®Jump-Starter with the supplied jump-start clamps
to jump-start a vehicle or boat engine. The Jump-Starter is compatible with 12V
vehicles.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is
designed for short term operation only. Operating the jump-start feature for
more than 4 seconds may cause damage to the unit. Allow the Jump-starter
to cool down for at least 30 seconds after each jump-start.
► To jump-start a vehicle engine:
1. Connect the jump-start clamps to the Jump-Starter
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery
and the black (-) clamp to the negative (-) terminal on the vehicle battery
3. Verify that the Jump-Starter and clamps are clear of any moving engine parts.
4. Start your engine, Be sure to crank for no more than 4 seconds at a time
and allow for 30 seconds in between starting attempts.
5. After starting the vehicle remove the Jump-starter and recharge it.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
7. Jump-Start LED bar function
Jump-start LED bar Reason and suggestion
OFF No clamp cable connected
Green ash Clamp cable connected, ready to connect to vehicle
Green ash (still ashing after
5 seconds of connection to
battery)
1. Turn off all vehicle accessories and lights; wait 5-10
minutes before reconnecting and try again.
2. If still ashing, the car battery may be below 3V and is
unsafe to use with this jump-starter.
Solid Green Good voltage and polarity - ready to start
Solid Red and beeping
while connecting
Reverse polarity or short - recheck connections
Solid Red - OR - 4 Fuel Gauge
LEDs ashing - After extended
starting
Over temperature - wait for the unit to cool down and reset.
Solid Red + 1 or 2 LED
on fuel gauge
Low internal battery voltage, please fully charge the unit
OFF - after 10 minutes Timed-out for safety, press power button to reset or re-at-
tach red clamp
Green ash after vehicle starts Reverse charge protection - Vehicle started, remove the unit
8. Specications
Electrical specications
Charging Input Voltage/Current 5V/2.0A
DC Adapter Input Voltage 12V
DC Adapter Output Voltage/Current 5V / 2.1 A
Safety certications / efciency certications UL (cTUVus), CEC/BC, FCC
(DC charger: CE,FCC)
Physical specications
Length 7.66 in (19.45 cm)
Width 3.31 in (8.40 cm)
Height 1.40 in (3.55 cm)
Weight (product only) 1.47 lbs (490 g)
9. Important safety instructions
IMPORTANT: Please read these general usage-related warnings and cautions
thoroughly before using this Jump-starter.
WARNING: When using this product, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the
product is used near children.
• Do not insert ngers or foreign objects into the product.
• Do not use this product with any application of which it was not intended.
• Use of an attachment not recommended or sold by the manufacturer may
result in risk of re, electric shock or injury to persons.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life
support systems or any other medical devices.
TM
1100 Amp Li-Ion Jump-Starter
(DRLJS110B/DRBTLC)
IMPORTANT: SAVE THESE INSTRUCTIONS
Misusing or incorrectly connecting the DURACELL®Jump-Starter may
damage the equipment or create hazardous conditions for users.
1. Download the PowerHub™app
The PowerHub™app enables advanced features:
• Battery monitoring and alerts
• Interactive step-by-step guide
• Live support
► Download the app to get started:
DuracellPower.com/App
Scan for app download
2. Product details
12
34
10 11
9
5 6
7 8
BLUETOOTH
1: Jump-start port
connects
to jump-start clamps.
2: USB port (2.4 Amps)
charges smartphones,
tablets and other devices.
3: Charging ‘IN’ port
connects to USB cable to
recharge the Jump-starter.
4: LED ashlight
features
high beam, low beam and
emergency/SOS mode.
5: Battery level button
and LED gauge
displays
battery charge level.
6: LED status light
bar
indicates state of the
Jump-Starter connection (see
Section 7).
7: Light button
activates the
LED ashlight.
8: Bluetooth button
Hold
3 seconds for pairing mode
(requires Duracell Power App).
9: Jump-start clamps
with SafeJump™ feature.
10: Carry bag ts into most
vehicle glove boxes.
11:
DC charger and USB
cable
for recharging the
Jump-Starter.
3. Charging the Jump-starter
WARNING: SHOCK HAZARD
Disconnect jump-start clamps before charging the Jump-starter.
CAUTION
Do not attempt to recharge the Jump-starter battery if it is frozen.
Gradually warm the frozen battery to 32 °F (0 °C) before recharging.
IMPORTANT: FULLY CHARGE BEFORE USE
Prior to using the Jump-starter for the rst time, ensure that the battery of
the Jump-starter is fully charged. If the battery has been fully discharged,
charging with a USB charger may take up to 4 hours.
IMPORTANT: PROPER CHARGER OUTPUT
For fastest possible recharging time, please be sure to use an AC or DC
charger with a rating of 2.0 Amps or higher. The charge times shown
assume the usage of a charger with a 2.0A or higher power rating.
CAUTION
The included DC charger is for charging only Li-Ion type rechargeable
batteries. Other types of batteries may burst causing personal injury or
damage.
A
B
C
►Charging/re-charging the Jump-Starter
Charging times: Partially discharged (or after using jump-starter) -
30-60 minutes; fully discharged jump-starter battery - up to 4 hours
Charging with the included DC charger:
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the DC charger into the included 12V vehicle socket (Fig. A) and
connect the small micro USB end of the included USB charging cable to
the ‘IN’ port. (Fig. B)
3. It is best to have the vehicle running while charging.
Charging with an AC charger (sold separately):
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the USB cable into your USB wall charger (Fig. C - wall charger
sold separately) and connect the small micro USB end of the included
USB charging cable to the ‘IN’ port (Fig. B).
IMPORTANT
If you keep the Jump-starter in storage, the battery will discharge over
time. Remember to recharge the battery after every use to make sure it is
ready when you need it, and at least once a year. Re-charging more often
will not harm the Jump-starter.
4. Checking the Jump-starter’s battery level
To check the battery’s charge level, press the battery level button on the Jump-
Starter. The LED fuel gauge will illuminate and display the current level of
available battery power. Four lights indicate a 100% charge.
IMPORTANT
Your Jump-starter will perform best when its battery is fully charged. If the
LED Fuel Gauge shows less than 100% charge, it is recommended to fully
recharge its battery (see Section 4: “Charging the Jump-starter” ).
5. Using the LED ashlight and USB port
►Using the LED light
The DURACELL® Jump-Starter has a built-in emergency light to provide a safe,
bright work light on the roadside and in other outdoor environments.
Press and release the light button to cycle through the 3 light modes. (High
beam, Low Beam and SOS)
►Using the USB port
The USB port provides up to 2.4 Amps of current to charge cell phones,
smartphones, tablets and other devices.
1. Open the protective cover over the USB port.
2. Connect your USB device (smartphone, tablet, etc.) to the USB port using
the USB cable supplied with your device.
3. Charging will automatically start.
6. Jump-starting a vehicle
You can use the DURACELL®Jump-Starter with the supplied jump-start clamps
to jump-start a vehicle or boat engine. The Jump-Starter is compatible with 12V
vehicles.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is
designed for short term operation only. Operating the jump-start feature for
more than 4 seconds may cause damage to the unit. Allow the Jump-starter
to cool down for at least 30 seconds after each jump-start.
► To jump-start a vehicle engine:
1. Connect the jump-start clamps to the Jump-Starter
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery
and the black (-) clamp to the negative (-) terminal on the vehicle battery
3. Verify that the Jump-Starter and clamps are clear of any moving engine parts.
4. Start your engine, Be sure to crank for no more than 4 seconds at a time
and allow for 30 seconds in between starting attempts.
5. After starting the vehicle remove the Jump-starter and recharge it.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
7. Jump-Start LED bar function
Jump-start LED bar Reason and suggestion
OFF No clamp cable connected
Green ash Clamp cable connected, ready to connect to vehicle
Green ash (still ashing after
5 seconds of connection to
battery)
1. Turn off all vehicle accessories and lights; wait 5-10
minutes before reconnecting and try again.
2. If still ashing, the car battery may be below 3V and is
unsafe to use with this jump-starter.
Solid Green Good voltage and polarity - ready to start
Solid Red and beeping
while connecting
Reverse polarity or short - recheck connections
Solid Red - OR - 4 Fuel Gauge
LEDs ashing - After extended
starting
Over temperature - wait for the unit to cool down and reset.
Solid Red + 1 or 2 LED
on fuel gauge
Low internal battery voltage, please fully charge the unit
OFF - after 10 minutes Timed-out for safety, press power button to reset or re-at-
tach red clamp
Green ash after vehicle starts Reverse charge protection - Vehicle started, remove the unit
8. Specications
Electrical specications
Charging Input Voltage/Current 5V/2.0A
DC Adapter Input Voltage 12V
DC Adapter Output Voltage/Current 5V / 2.1 A
Safety certications / efciency certications UL (cTUVus), CEC/BC, FCC
(DC charger: CE,FCC)
Physical specications
Length 7.66 in (19.45 cm)
Width 3.31 in (8.40 cm)
Height 1.40 in (3.55 cm)
Weight (product only) 1.47 lbs (490 g)
9. Important safety instructions
IMPORTANT: Please read these general usage-related warnings and cautions
thoroughly before using this Jump-starter.
WARNING: When using this product, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the
product is used near children.
• Do not insert ngers or foreign objects into the product.
• Do not use this product with any application of which it was not intended.
• Use of an attachment not recommended or sold by the manufacturer may
result in risk of re, electric shock or injury to persons.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life
support systems or any other medical devices.
TM
1100 Amp Li-Ion Jump-Starter
(DRLJS110B/DRBTLC)
IMPORTANT: SAVE THESE INSTRUCTIONS
Misusing or incorrectly connecting the DURACELL®Jump-Starter may
damage the equipment or create hazardous conditions for users.
1. Download the PowerHub™app
The PowerHub™app enables advanced features:
• Battery monitoring and alerts
• Interactive step-by-step guide
• Live support
► Download the app to get started:
DuracellPower.com/App
Scan for app download
2. Product details
12
34
10 11
9
5 6
7 8
BLUETOOTH
1: Jump-start port
connects
to jump-start clamps.
2: USB port (2.4 Amps)
charges smartphones,
tablets and other devices.
3: Charging ‘IN’ port
connects to USB cable to
recharge the Jump-starter.
4: LED ashlight
features
high beam, low beam and
emergency/SOS mode.
5: Battery level button
and LED gauge
displays
battery charge level.
6: LED status light
bar
indicates state of the
Jump-Starter connection (see
Section 7).
7: Light button
activates the
LED ashlight.
8: Bluetooth button
Hold
3 seconds for pairing mode
(requires Duracell Power App).
9: Jump-start clamps
with SafeJump™ feature.
10: Carry bag ts into most
vehicle glove boxes.
11:
DC charger and USB
cable
for recharging the
Jump-Starter.
3. Charging the Jump-starter
WARNING: SHOCK HAZARD
Disconnect jump-start clamps before charging the Jump-starter.
CAUTION
Do not attempt to recharge the Jump-starter battery if it is frozen.
Gradually warm the frozen battery to 32 °F (0 °C) before recharging.
IMPORTANT: FULLY CHARGE BEFORE USE
Prior to using the Jump-starter for the rst time, ensure that the battery of
the Jump-starter is fully charged. If the battery has been fully discharged,
charging with a USB charger may take up to 4 hours.
IMPORTANT: PROPER CHARGER OUTPUT
For fastest possible recharging time, please be sure to use an AC or DC
charger with a rating of 2.0 Amps or higher. The charge times shown
assume the usage of a charger with a 2.0A or higher power rating.
CAUTION
The included DC charger is for charging only Li-Ion type rechargeable
batteries. Other types of batteries may burst causing personal injury or
damage.
A
B
C
►Charging/re-charging the Jump-Starter
Charging times: Partially discharged (or after using jump-starter) -
30-60 minutes; fully discharged jump-starter battery - up to 4 hours
Charging with the included DC charger:
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the DC charger into the included 12V vehicle socket (Fig. A) and
connect the small micro USB end of the included USB charging cable to
the ‘IN’ port. (Fig. B)
3. It is best to have the vehicle running while charging.
Charging with an AC charger (sold separately):
1. Disconnect any cables from the Jump-starter and USB ports.
2. Plug the USB cable into your USB wall charger (Fig. C - wall charger
sold separately) and connect the small micro USB end of the included
USB charging cable to the ‘IN’ port (Fig. B).
IMPORTANT
If you keep the Jump-starter in storage, the battery will discharge over
time. Remember to recharge the battery after every use to make sure it is
ready when you need it, and at least once a year. Re-charging more often
will not harm the Jump-starter.
4. Checking the Jump-starter’s battery level
To check the battery’s charge level, press the battery level button on the Jump-
Starter. The LED fuel gauge will illuminate and display the current level of
available battery power. Four lights indicate a 100% charge.
IMPORTANT
Your Jump-starter will perform best when its battery is fully charged. If the
LED Fuel Gauge shows less than 100% charge, it is recommended to fully
recharge its battery (see Section 4: “Charging the Jump-starter” ).
5. Using the LED ashlight and USB port
►Using the LED light
The DURACELL® Jump-Starter has a built-in emergency light to provide a safe,
bright work light on the roadside and in other outdoor environments.
Press and release the light button to cycle through the 3 light modes. (High
beam, Low Beam and SOS)
►Using the USB port
The USB port provides up to 2.4 Amps of current to charge cell phones,
smartphones, tablets and other devices.
1. Open the protective cover over the USB port.
2. Connect your USB device (smartphone, tablet, etc.) to the USB port using
the USB cable supplied with your device.
3. Charging will automatically start.
6. Jump-starting a vehicle
You can use the DURACELL®Jump-Starter with the supplied jump-start clamps
to jump-start a vehicle or boat engine. The Jump-Starter is compatible with 12V
vehicles.
WARNING: FIRE HAZARD
Do not crank the engine for more than 4 seconds. The jump-start feature is
designed for short term operation only. Operating the jump-start feature for
more than 4 seconds may cause damage to the unit. Allow the Jump-starter
to cool down for at least 30 seconds after each jump-start.
► To jump-start a vehicle engine:
1. Connect the jump-start clamps to the Jump-Starter
2. Connect the red (+) clamp to the positive (+) terminal on the vehicle battery
and the black (-) clamp to the negative (-) terminal on the vehicle battery
3. Verify that the Jump-Starter and clamps are clear of any moving engine parts.
4. Start your engine, Be sure to crank for no more than 4 seconds at a time
and allow for 30 seconds in between starting attempts.
5. After starting the vehicle remove the Jump-starter and recharge it.
Red POSITIVE (“+”)
clamp
connects
to
positive
battery
terminal
Black NEGATIVE (“
-
”) clamp
connects to the negative battery
terminal OR
metal part of car
(block, cylinder, etc)
7. Jump-Start LED bar function
Jump-start LED bar Reason and suggestion
OFF No clamp cable connected
Green ash Clamp cable connected, ready to connect to vehicle
Green ash (still ashing after
5 seconds of connection to
battery)
1. Turn off all vehicle accessories and lights; wait 5-10
minutes before reconnecting and try again.
2. If still ashing, the car battery may be below 3V and is
unsafe to use with this jump-starter.
Solid Green Good voltage and polarity - ready to start
Solid Red and beeping
while connecting
Reverse polarity or short - recheck connections
Solid Red - OR - 4 Fuel Gauge
LEDs ashing - After extended
starting
Over temperature - wait for the unit to cool down and reset.
Solid Red + 1 or 2 LED
on fuel gauge
Low internal battery voltage, please fully charge the unit
OFF - after 10 minutes Timed-out for safety, press power button to reset or re-at-
tach red clamp
Green ash after vehicle starts Reverse charge protection - Vehicle started, remove the unit
8. Specications
Electrical specications
Charging Input Voltage/Current 5V/2.0A
DC Adapter Input Voltage 12V
DC Adapter Output Voltage/Current 5V / 2.1 A
Safety certications / efciency certications UL (cTUVus), CEC/BC, FCC
(DC charger: CE,FCC)
Physical specications
Length 7.66 in (19.45 cm)
Width 3.31 in (8.40 cm)
Height 1.40 in (3.55 cm)
Weight (product only) 1.47 lbs (490 g)
9. Important safety instructions
IMPORTANT: Please read these general usage-related warnings and cautions
thoroughly before using this Jump-starter.
WARNING: When using this product, basic
precautions should always be followed, including the
following:
• Read all the instructions before using the product.
• To reduce the risk of injury, close supervision is necessary when the
product is used near children.
• Do not insert ngers or foreign objects into the product.
• Do not use this product with any application of which it was not intended.
• Use of an attachment not recommended or sold by the manufacturer may
result in risk of re, electric shock or injury to persons.
WARNING: Medical equipment
This product is NOT tested, designed nor intended to be used with life
support systems or any other medical devices.
TM
13. Product Registration
For complete warranty coverage, please register your Duracell product
within fourteen days of purchase.
Visit DuracellPower.com/Register
or scan the QR code below to register.
WARNING: Proper application
• Do not use the product if it is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not operate the power pack with a damaged cord or plug.
• Do not disassemble the power pack, contact the manufacturer when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING: Risk of explosive gases
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF THE
UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS
EACH TIME YOU USE THE JUMP-STARTER.
To reduce risk of vehicle battery explosion, follow these instructions in
vicinity of the battery. Review cautionary marking on this product and on
vehicle engine.
WARNING: Personal precautions
• Consider having someone close enough by to come to your aid when you
work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes. Wear complete eye protection and clothing
protection. Avoid touching your eyes while working near a vehicle battery.
• If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately ood eye with running cold water for
at least 10 minutes and get medical attention immediately.
• NEVER smoke or allow a spark or ame in vicinity of a vehicle battery or
engine.
• Be extra cautious to reduce risk of dropping a metal tool onto the vehicle
battery. It might spark or short-circuit battery or other electrical part that
may cause an explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn.
• When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery, avoid
any contact with this material. If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not expose a power pack to re or excessive temperature. Exposure
to re or temperature above 265°F (130°C) may cause an explosion.
• Attach output clamps to a battery and chassis as indicated in these
instructions. Never allow the output clamps to touch one another.
10. Recycling
DURACELL®is committed to environmental responsibility and recommends
that electronic devices be disposed of properly. Please contact your local city
ofces for information on recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
11. Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to calling,
please review the technical support tips below. Call from a phone where you
have access to your mobile device
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL®product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada to 1-800-300-1857
Outside of the US/Canada: 1-805-437-7765
Written inquires should be directed to:
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
Email inquires should be directed to:
info@DuracellPower.com
12. Warranty and return information
Two Year Limited Warranty
The DURACELL®product carries a limited warranty against defects in material
and workmanship under normal use and service for two years from the original
date of purchase. The manufacturer or distributor, at its option, shall repair or
replace the defective unit covered by this warranty. Please retain the dated
sales receipt as evidence of the date of purchase as it will be required for any
warranty service. In order to keep the warranty in effect, the product must have
been handled and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident, misuse,
abuse or negligence
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent
permitted by law, the manufacturer and distributor disclaim all other implied or
express warranties including all warranties of merchantability and/or tness for
any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated
in the limited warranty described herein, the manufacturer and distributor
shall not be liable for any damages, whether direct, indirect, incidental,
special,consequential, exemplary, or otherwise, including lost revenues, lost
prots, loss of use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims, arising out
of any theory of recovery, including statutory, contract or tort. Not withstanding
the term of any limited or implied warranty, or in the event that any limited
warranty fails of its essential purpose, in no event will the manufacturer’s and
distributors entire liability exceed the purchase price of this product. Some
states and provinces do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you. This limited warranty gives you specic legal rights. You may have
other rights which vary from state to state and province to province.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation of this product
is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
© 2019 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Battery-Biz Inc. is under license. Other trademarks and trade names are those of their respective owners.
UM-DRLJS110B/DRBTLC Rev 20190807
which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Canada IC Statement
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference that may cause undesired
operation of the device.
Cet équipement est conforme à l’exposition aux rayonnements Industry
Canada limites établies pour un environnement non contrôlé.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles
de provoquer un fonctionnement non souhaité de l’appareil.
13. Product Registration
For complete warranty coverage, please register your Duracell product
within fourteen days of purchase.
Visit DuracellPower.com/Register
or scan the QR code below to register.
WARNING: Proper application
• Do not use the product if it is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not operate the power pack with a damaged cord or plug.
• Do not disassemble the power pack, contact the manufacturer when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING: Risk of explosive gases
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF THE
UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS
EACH TIME YOU USE THE JUMP-STARTER.
To reduce risk of vehicle battery explosion, follow these instructions in
vicinity of the battery. Review cautionary marking on this product and on
vehicle engine.
WARNING: Personal precautions
• Consider having someone close enough by to come to your aid when you
work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes. Wear complete eye protection and clothing
protection. Avoid touching your eyes while working near a vehicle battery.
• If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately ood eye with running cold water for
at least 10 minutes and get medical attention immediately.
• NEVER smoke or allow a spark or ame in vicinity of a vehicle battery or
engine.
• Be extra cautious to reduce risk of dropping a metal tool onto the vehicle
battery. It might spark or short-circuit battery or other electrical part that
may cause an explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn.
• When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery, avoid
any contact with this material. If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not expose a power pack to re or excessive temperature. Exposure
to re or temperature above 265°F (130°C) may cause an explosion.
• Attach output clamps to a battery and chassis as indicated in these
instructions. Never allow the output clamps to touch one another.
10. Recycling
DURACELL®is committed to environmental responsibility and recommends
that electronic devices be disposed of properly. Please contact your local city
ofces for information on recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
11. Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to calling,
please review the technical support tips below. Call from a phone where you
have access to your mobile device
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL®product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada to 1-800-300-1857
Outside of the US/Canada: 1-805-437-7765
Written inquires should be directed to:
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
Email inquires should be directed to:
info@DuracellPower.com
12. Warranty and return information
Two Year Limited Warranty
The DURACELL®product carries a limited warranty against defects in material
and workmanship under normal use and service for two years from the original
date of purchase. The manufacturer or distributor, at its option, shall repair or
replace the defective unit covered by this warranty. Please retain the dated
sales receipt as evidence of the date of purchase as it will be required for any
warranty service. In order to keep the warranty in effect, the product must have
been handled and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident, misuse,
abuse or negligence
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent
permitted by law, the manufacturer and distributor disclaim all other implied or
express warranties including all warranties of merchantability and/or tness for
any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated
in the limited warranty described herein, the manufacturer and distributor
shall not be liable for any damages, whether direct, indirect, incidental,
special,consequential, exemplary, or otherwise, including lost revenues, lost
prots, loss of use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims, arising out
of any theory of recovery, including statutory, contract or tort. Not withstanding
the term of any limited or implied warranty, or in the event that any limited
warranty fails of its essential purpose, in no event will the manufacturer’s and
distributors entire liability exceed the purchase price of this product. Some
states and provinces do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you. This limited warranty gives you specic legal rights. You may have
other rights which vary from state to state and province to province.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation of this product
is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
© 2019 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Battery-Biz Inc. is under license. Other trademarks and trade names are those of their respective owners.
UM-DRLJS110B/DRBTLC Rev 20190807
which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Canada IC Statement
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference that may cause undesired
operation of the device.
Cet équipement est conforme à l’exposition aux rayonnements Industry
Canada limites établies pour un environnement non contrôlé.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles
de provoquer un fonctionnement non souhaité de l’appareil.
13. Product Registration
For complete warranty coverage, please register your Duracell product
within fourteen days of purchase.
Visit DuracellPower.com/Register
or scan the QR code below to register.
WARNING: Proper application
• Do not use the product if it is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not operate the power pack with a damaged cord or plug.
• Do not disassemble the power pack, contact the manufacturer when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING: Risk of explosive gases
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF THE
UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS
EACH TIME YOU USE THE JUMP-STARTER.
To reduce risk of vehicle battery explosion, follow these instructions in
vicinity of the battery. Review cautionary marking on this product and on
vehicle engine.
WARNING: Personal precautions
• Consider having someone close enough by to come to your aid when you
work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes. Wear complete eye protection and clothing
protection. Avoid touching your eyes while working near a vehicle battery.
• If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately ood eye with running cold water for
at least 10 minutes and get medical attention immediately.
• NEVER smoke or allow a spark or ame in vicinity of a vehicle battery or
engine.
• Be extra cautious to reduce risk of dropping a metal tool onto the vehicle
battery. It might spark or short-circuit battery or other electrical part that
may cause an explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn.
• When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery, avoid
any contact with this material. If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not expose a power pack to re or excessive temperature. Exposure
to re or temperature above 265°F (130°C) may cause an explosion.
• Attach output clamps to a battery and chassis as indicated in these
instructions. Never allow the output clamps to touch one another.
10. Recycling
DURACELL®is committed to environmental responsibility and recommends
that electronic devices be disposed of properly. Please contact your local city
ofces for information on recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
11. Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to calling,
please review the technical support tips below. Call from a phone where you
have access to your mobile device
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL®product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada to 1-800-300-1857
Outside of the US/Canada: 1-805-437-7765
Written inquires should be directed to:
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
Email inquires should be directed to:
info@DuracellPower.com
12. Warranty and return information
Two Year Limited Warranty
The DURACELL®product carries a limited warranty against defects in material
and workmanship under normal use and service for two years from the original
date of purchase. The manufacturer or distributor, at its option, shall repair or
replace the defective unit covered by this warranty. Please retain the dated
sales receipt as evidence of the date of purchase as it will be required for any
warranty service. In order to keep the warranty in effect, the product must have
been handled and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident, misuse,
abuse or negligence
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent
permitted by law, the manufacturer and distributor disclaim all other implied or
express warranties including all warranties of merchantability and/or tness for
any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated
in the limited warranty described herein, the manufacturer and distributor
shall not be liable for any damages, whether direct, indirect, incidental,
special,consequential, exemplary, or otherwise, including lost revenues, lost
prots, loss of use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims, arising out
of any theory of recovery, including statutory, contract or tort. Not withstanding
the term of any limited or implied warranty, or in the event that any limited
warranty fails of its essential purpose, in no event will the manufacturer’s and
distributors entire liability exceed the purchase price of this product. Some
states and provinces do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you. This limited warranty gives you specic legal rights. You may have
other rights which vary from state to state and province to province.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation of this product
is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
© 2019 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Battery-Biz Inc. is under license. Other trademarks and trade names are those of their respective owners.
UM-DRLJS110B/DRBTLC Rev 20190807
which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Canada IC Statement
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference that may cause undesired
operation of the device.
Cet équipement est conforme à l’exposition aux rayonnements Industry
Canada limites établies pour un environnement non contrôlé.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles
de provoquer un fonctionnement non souhaité de l’appareil.
13. Product Registration
For complete warranty coverage, please register your Duracell product
within fourteen days of purchase.
Visit DuracellPower.com/Register
or scan the QR code below to register.
WARNING: Proper application
• Do not use the product if it is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not operate the power pack with a damaged cord or plug.
• Do not disassemble the power pack, contact the manufacturer when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING: Risk of explosive gases
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF THE
UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS
EACH TIME YOU USE THE JUMP-STARTER.
To reduce risk of vehicle battery explosion, follow these instructions in
vicinity of the battery. Review cautionary marking on this product and on
vehicle engine.
WARNING: Personal precautions
• Consider having someone close enough by to come to your aid when you
work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes. Wear complete eye protection and clothing
protection. Avoid touching your eyes while working near a vehicle battery.
• If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately ood eye with running cold water for
at least 10 minutes and get medical attention immediately.
• NEVER smoke or allow a spark or ame in vicinity of a vehicle battery or
engine.
• Be extra cautious to reduce risk of dropping a metal tool onto the vehicle
battery. It might spark or short-circuit battery or other electrical part that
may cause an explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn.
• When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery, avoid
any contact with this material. If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not expose a power pack to re or excessive temperature. Exposure
to re or temperature above 265°F (130°C) may cause an explosion.
• Attach output clamps to a battery and chassis as indicated in these
instructions. Never allow the output clamps to touch one another.
10. Recycling
DURACELL®is committed to environmental responsibility and recommends
that electronic devices be disposed of properly. Please contact your local city
ofces for information on recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
11. Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to calling,
please review the technical support tips below. Call from a phone where you
have access to your mobile device
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL®product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada to 1-800-300-1857
Outside of the US/Canada: 1-805-437-7765
Written inquires should be directed to:
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
Email inquires should be directed to:
info@DuracellPower.com
12. Warranty and return information
Two Year Limited Warranty
The DURACELL®product carries a limited warranty against defects in material
and workmanship under normal use and service for two years from the original
date of purchase. The manufacturer or distributor, at its option, shall repair or
replace the defective unit covered by this warranty. Please retain the dated
sales receipt as evidence of the date of purchase as it will be required for any
warranty service. In order to keep the warranty in effect, the product must have
been handled and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident, misuse,
abuse or negligence
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent
permitted by law, the manufacturer and distributor disclaim all other implied or
express warranties including all warranties of merchantability and/or tness for
any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated
in the limited warranty described herein, the manufacturer and distributor
shall not be liable for any damages, whether direct, indirect, incidental,
special,consequential, exemplary, or otherwise, including lost revenues, lost
prots, loss of use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims, arising out
of any theory of recovery, including statutory, contract or tort. Not withstanding
the term of any limited or implied warranty, or in the event that any limited
warranty fails of its essential purpose, in no event will the manufacturer’s and
distributors entire liability exceed the purchase price of this product. Some
states and provinces do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you. This limited warranty gives you specic legal rights. You may have
other rights which vary from state to state and province to province.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation of this product
is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
© 2019 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Battery-Biz Inc. is under license. Other trademarks and trade names are those of their respective owners.
UM-DRLJS110B/DRBTLC Rev 20190807
which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Canada IC Statement
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference that may cause undesired
operation of the device.
Cet équipement est conforme à l’exposition aux rayonnements Industry
Canada limites établies pour un environnement non contrôlé.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles
de provoquer un fonctionnement non souhaité de l’appareil.
13. Product Registration
For complete warranty coverage, please register your Duracell product
within fourteen days of purchase.
Visit DuracellPower.com/Register
or scan the QR code below to register.
WARNING: Proper application
• Do not use the product if it is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not operate the power pack with a damaged cord or plug.
• Do not disassemble the power pack, contact the manufacturer when
service or repair is required. Incorrect reassembly may result in a risk
of re or electric shock.
WARNING: Risk of explosive gases
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF THE
UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS
EACH TIME YOU USE THE JUMP-STARTER.
To reduce risk of vehicle battery explosion, follow these instructions in
vicinity of the battery. Review cautionary marking on this product and on
vehicle engine.
WARNING: Personal precautions
• Consider having someone close enough by to come to your aid when you
work near a lead-acid battery.
• Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes. Wear complete eye protection and clothing
protection. Avoid touching your eyes while working near a vehicle battery.
• If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately ood eye with running cold water for
at least 10 minutes and get medical attention immediately.
• NEVER smoke or allow a spark or ame in vicinity of a vehicle battery or
engine.
• Be extra cautious to reduce risk of dropping a metal tool onto the vehicle
battery. It might spark or short-circuit battery or other electrical part that
may cause an explosion.
• Remove personal metal items such as rings, bracelets, necklaces, and
watches when working with a lead-acid battery. A lead-acid battery can
produce a short-circuit current high enough to weld a ring or the like to
metal, causing a severe burn.
• When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
• Under abusive conditions, liquid may be ejected from the battery, avoid
any contact with this material. If contact accidentally occurs, ush with
water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not expose a power pack to re or excessive temperature. Exposure
to re or temperature above 265°F (130°C) may cause an explosion.
• Attach output clamps to a battery and chassis as indicated in these
instructions. Never allow the output clamps to touch one another.
10. Recycling
DURACELL®is committed to environmental responsibility and recommends
that electronic devices be disposed of properly. Please contact your local city
ofces for information on recycling and disposal programs for e-waste.
For instructions on how to recycle this product visit
http://www.call2recycle.org.
11. Contacting Customer Support
If you experience any problems or have any questions regarding your
DURACELL® product, free technical support is available. Prior to calling,
please review the technical support tips below. Call from a phone where you
have access to your mobile device
Be prepared to provide the following information:
- Name, address and telephone number
- Name of the DURACELL®product
- Make and model of your device
- Symptoms of the problem(s) and what led to them
Technical Support is available by telephone:
U.S. and Canada to 1-800-300-1857
Outside of the US/Canada: 1-805-437-7765
Written inquires should be directed to:
DURACELL® Product Inquiry
1380 Flynn Road, Camarillo, CA 93012, USA
Email inquires should be directed to:
info@DuracellPower.com
12. Warranty and return information
Two Year Limited Warranty
The DURACELL®product carries a limited warranty against defects in material
and workmanship under normal use and service for two years from the original
date of purchase. The manufacturer or distributor, at its option, shall repair or
replace the defective unit covered by this warranty. Please retain the dated
sales receipt as evidence of the date of purchase as it will be required for any
warranty service. In order to keep the warranty in effect, the product must have
been handled and used as described in the instructions accompanying this
warranty. This warranty does not cover any damage due to accident, misuse,
abuse or negligence
Disclaimer Of Warranty
The limited warranty described herein is your sole remedy. To the extent
permitted by law, the manufacturer and distributor disclaim all other implied or
express warranties including all warranties of merchantability and/or tness for
any particular purpose.
Limitation Of Liability
Except to the extent of repairing or replacing this product as expressly stated
in the limited warranty described herein, the manufacturer and distributor
shall not be liable for any damages, whether direct, indirect, incidental,
special,consequential, exemplary, or otherwise, including lost revenues, lost
prots, loss of use of software, loss or recovery of data, rental of replacement
equipment, downtime, damage to property, and third-party claims, arising out
of any theory of recovery, including statutory, contract or tort. Not withstanding
the term of any limited or implied warranty, or in the event that any limited
warranty fails of its essential purpose, in no event will the manufacturer’s and
distributors entire liability exceed the purchase price of this product. Some
states and provinces do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you. This limited warranty gives you specic legal rights. You may have
other rights which vary from state to state and province to province.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation of this product
is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
© 2019 Duracell. Bethel, CT 06801. DURACELL® is a registered trademark of Duracell U.S. Operations, Inc., used under
license. All rights reserved. All logos and trademarks are used for identication purposes only and may be trademarks or
registered trademarks of their respective holders.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Battery-Biz Inc. is under license. Other trademarks and trade names are those of their respective owners.
UM-DRLJS110B/DRBTLC Rev 20190807
which the receiver is connected.
• Consult the dealer or an experienced technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance with the FCC Rules could void the user’s authority to operate this
equipment.
Canada IC Statement
This equipment complies with Industry Canada radiation exposure limits set
forth for an uncontrolled environment.
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference that may cause undesired
operation of the device.
Cet équipement est conforme à l’exposition aux rayonnements Industry
Canada limites établies pour un environnement non contrôlé.
Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes :
1. cet appareil ne doit pas provoquer d’interférences et
2. cet appareil doit accepter toute interférence, y compris celles susceptibles
de provoquer un fonctionnement non souhaité de l’appareil.
Table of contents
Other Duracell Remote Starter manuals
