DuraVision FDX1502N User manual

Important
Please read this User’s Manual and Setup Manual (separate volume)
carefully to familiarize yourself with safe and effective usage.
• Please refer to the Setup Manual for basic information ranging from
connection of the monitor to a PC to using the monitor.
• Please refer to the NetDA Manager User’s Manual for information on
network connection settings and operations.
• Please refer to the Touch Panel Driver User’s Manual for touch panel
settings and operations (for FDX1502NT only).
• The latest User’s Manual is available for download from our web site:
http://www.eizo.com
Cover

2
This product has been adjusted specically for use in the region to which it was originally shipped. If operated
outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information condential
unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please note that
EIZO monitor specications are subject to change without notice.

3
Noticeforthismonitor
Notice for this monitor
Aside from creating documents, viewing multimedia content, and other general purposes, this product is also suited to
the dedicated usages such as operation of terminal equipment.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is
used outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications noted in this manual are only applicable when the following are used:
· Signal cables specied by us
Only use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a
stable display.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to
“Cleaning” (page 4)).
The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on
the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.
The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt
to brush with tissues as this may scratch the panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may
occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until
the dew condensation disappears, otherwise it may cause some damage to the monitor.
(Cautions for the Use of the Touch Panel)
• During touch operation
Be careful of the following points. Otherwise, damage may occur to the monitor.
- Do not strongly press, scratch, or poke the panel.
- Do not touch the panel with hard objects such as ballpoint pens or metals.

4Noticeforthismonitor
Cleaning
Attention
• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel,
and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not allow liquid to enter the clearance between the panel and the panel frame.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with
water.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to
the environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5
CONTENTS
CONTENTS
Cover ...................................................................... 1
Notice for this monitor ......................................... 3
Cleaning .................................................................... 4
To use the monitor comfortably ............................. 4
CONTENTS ............................................................. 5
Chapter 1 Introduction ....................................... 6
1-1. Features ......................................................... 6
1-2. EIZO LCD Utility Disk.................................... 7
●Diskcontentsandsoftwareoverview............. 7
●TouseNetDAManager................................... 7
●Tousetouchpaneldriver............................... 7
1-3. Basic Operations and Functions ................ 8
●BasicAdjustmentmenuoperations................ 8
●Functions......................................................... 9
Chapter 2 Adjusting Screens .......................... 10
2-1. Setting the Resolution ................................10
●Displayresolution...........................................10
●Settingresolution...........................................10
2-2. Displaying Screen Correctly.......................11
●NetworkConnection.......................................11
●AnalogConnection.........................................11
2-3. Adjusting Color ............................................15
●Toselectthedisplaymode(ColorMode).......15
●Toperformadvancedadjustments................15
●Adjustablesettingsineachmode..................15
●Toadjustbrightness.......................................16
●Toadjustcontrast...........................................16
●Toadjustcolortemperature...........................17
●Toadjustgain.................................................17
Chapter 3 Setting Monitor ............................... 18
3-1. Adjusting Volume.........................................18
3-2. Setting Input Signal Selection....................18
3-3. Changing Adjustment Menu Display
Position .........................................................18
3-4. Setting Language .........................................19
3-5. Locking Buttons ...........................................19
●Tolockadjustments/settingsinthe
Adjustmentmenu...........................................19
●Tolockalloperations.....................................19
3-6. Setting the EIZO Logo Display ...................19
3-7. Enabling/Disabling DDC/CI
communication (for analog connection
only) ...............................................................19
3-8. Resetting the Monitor to the Default
Settings ........................................................ 20
●Toresetthenetworkconguration
information.................................................... 20
●Toresetthecoloradjustments...................... 20
●Toresetalladjustmentstothedefault
settings.......................................................... 20
Chapter 4 Power Saving Functions ................ 21
4-1. Power Saving Mode .....................................21
4-2. Setting Power Indicator ...............................21
4-3. Enabling/Disabling Automatic
Brightness Adjustment .............................. 22
4-4. Setting Network Power Control Function ... 22
4-5. Enabling/Disabling Auto Power-OFF ........ 22
Chapter 5 Troubleshooting .............................. 23
5-1. No picture .................................................... 23
5-2. Imaging problems ....................................... 24
5-3. Network connection problems .................. 25
5-4. Other problems ........................................... 25
5-5. Touch panel problems (for FDX1502NT
only) .............................................................. 26
Chapter 6 Reference ........................................ 27
6-1. How to Attach the Optional Arm ............... 27
6-2. Displaying Monitor Information ................ 28
6-3. Displaying Network Conguration
Information .................................................. 28
6-4. Specications ............................................. 29
6-5. Glossary ....................................................... 35
6-6. Preset Timing .............................................. 38
Appendix .............................................................. 39
Trademark ............................................................... 39
CE ............................................................................. 40
LIMITED WARRANTY ..............................................41
Recycling Information ........................................... 50
China Measures for RoHS Compliance in
ChinaRoHS .............................................................. 54

6Chapter1Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
• 15” LCD
• Applicable to the resolution of 1024 × 768.
• High-intensity panel
Maintains visibility under high-illumination conditions
(Maximum brightness) FDX1502N: 400cd/m2, FDX1502NT: 320cd/m2
• LED backlight LCD panel
No mercury, a hazardous substance, is used.
• Supports network connection
• Video and audio PC signals can be input via a network.
- Wired LAN standard: Complies with 1000BASE-T, 100BASE-TX, and 10BASE-T.
- Wireless LAN standard: Complies with IEEE802.11a / b / g / n.
The monitor can be used wirelessly even with the PC positioned away from the monitor.
• Access point function
Using the access point function, it is now possible to link the monitor to the PC over a wireless LAN but also over a
wired LAN connection.
• Communication with various USB devices is also possible via a network.
PCs can be operated using the keyboard or mouse connected to the monitor’s USB ports; other USB peripherals such
as a printer and storage devices can also be accessed and operated via the PCs.
• Network connection can be established via the special software application “NetDA Manager”.
It is possible to search for monitors on the network, to link to or unlink from these monitors, and to perform network
conguration.
• Mirror mode (duplicate), Extend mode (extend) function
Mirror mode or Extend mode can be used according to monitor application. In mirror mode, the same image that is
displayed on the PC screen is also displayed on the external monitor. In Extend mode, the PC desktop is extended off
its own screen and onto the external monitor.
• The image displayed on the PC screen can be displayed and controlled on up to 6 monitors.
• PC lter function
It is possible to restrict (“lter”) by registering the PC which will be linked to the monitor in advance.
• Built-in stereo speakers
• Supports a wide range of operating temperatures and operating humidity
- Operating temperature : 0°C to 50°C (32°F to 122°F)
- Operating humidity: 20% to 90% R.H. (wet bulb temperature ≤ 39 °C (102 °F), no condensation)
• A 2-year long-term warranty for 24-hour continuous use
• Resistive technology touch panel function (for FDX1502NT only)
Compatible with Microsoft Windows 7 / Vista / XP. The touch panel can be operated even when wearing gloves.

7
Chapter1Introduction
1-2. EIZO LCD Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk
contents and the overview of the software programs.
●Disk contents and software overview
The disk includes various software applications and User’s Manuals. Refer to Readme.txt le on the disk for
software startup procedures or le access procedures.
Item Overview
Screenadjustmentpatternles Usedwhenadjustingtheimagemanuallyoverananalogconnection.
NetDAManager Specialsoftwarewhichallowsanetworkconnectiontobeestablished.
TouchPanelDriver*1 Driverfortouchpanel
NetDAManagerUser’sManual(PDFle)
TouchPanelDriverUser’sManual(PDFle)*1
User’sManualofthismonitor(PDFle)
A“Readme.txt”le
*1 Used only for the FDX1502NT.
●To use NetDA Manager
For information how to install, set up, or use the NetDA Manager, see the NetDA Manager User’s Manual (on
the CD-ROM).
●To use touch panel driver
For information on how to install or use the touch panel driver, see the Touch Panel Driver User’s Manual (on
the CD-ROM).

8Chapter1Introduction
1-3. Basic Operations and Functions
●Basic Adjustment menu operations
1. Displaying Adjustment Menu
1. Press . The adjustment menu appears.
Example:Duringnetworkconnection
2.
Adjusting/Setting
1. Choose a menu to adjust/set with or , and then press . The Sub menu appears.
2. Choose an item to adjust/set with or , and then press . The adjustment/ setting menu appears.
3. Adjust/set the selected item with or , and then press .
3.
Exiting
1. Choose <Return> from the Sub menu and press . The Main menu appears.
2. Choose <Exit> from the Main menu and press . The Adjustment menu exits.
Note
• The Adjustment menu can also be exited by pressing twice quickly.

9
Chapter1Introduction
●Functions
The following table shows all the Adjustment menu’s adjustment and setting menus.
Main menu Setting Reference
Network LANPowerMode “4-4.SettingNetworkPowerControlFunction”(page22)
Reset “Toresetthenetworkcongurationinformation”(page20)
AutoAdjustment*1 Screen “2-2.DisplayingScreenCorrectly”(page11)
Range
Screen Clock*1
Phase*1
Hor.Position*1
Ver.Position*1
Smoothing
Color*2 Brightness “2-3.AdjustingColor”(page15)
ColorMode
Contrast
Temperature
Gain
Reset “Toresetthecoloradjustments”(page20)
Others InputSignal “3-2.SettingInputSignalSelection”(page18)
OffTimer “4-5.Enabling/DisablingAutoPower-OFF”(page22)
MenuPosition “3-3.ChangingAdjustmentMenuDisplayPosition”(page18)
AutoEcoView “4-3.Enabling/DisablingAutomaticBrightnessAdjustment”
(page22)
PowerIndicator “4-2.SettingPowerIndicator”(page21)
Reset “Toresetalladjustmentstothedefaultsettings”(page20)
Information “6-2.DisplayingMonitorInformation”(page28)
Language “3-4.SettingLanguage”(page19)
*1 For analog connection only
*2
The adjustment/settings available on the <Color> menu depend on the selected Color Mode.

10 Chapter2AdjustingScreens
Chapter 2 Adjusting Screens
2-1. Setting the Resolution
●Display resolution
For details on compatible resolutions, refer to “Compatible Resolutions” (page 32).
●Setting resolution
When you connect the monitor to the PC and nd that the resolution is improper, or when you want to change
the resolution, follow the procedure below.
Windows 7
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Screen resolution”.
3. Click the “Identify” button in the “Screen resolution” dialog box to display the number.
4. Select the number of the monitor for which you want to change the resolution in “Display”.
5. Click “Resolution” to select the desired resolution.
6. Click the “OK” button.
7. When a conrmation dialog box is displayed, click “Keep changes”.
Windows Vista
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Personalize”.
3. On the “Personalization” window, click “Display Settings”.
4. Select the “Monitor” tab in the “Display Settings” dialog box.
5. Click the “Identify Monitors” button to display the number.
6. Select the number of the monitor for which you want to change the resolution. Select the desired resolution
from the “Resolution” eld.
7. Click the “OK” button.
8. When a conrmation dialog box is displayed, click “Yes”.
Windows XP
1. Right-click the mouse anywhere on the desktop except for icons.
2. From the displayed menu, click “Properties”.
3. Select the “Settings” tab of the “Display Properties” dialog box.
4. Click the “Identity” button to display the number.
5. Select the number of the monitor for which you want to change the resolution in “Display”.
6. Select desired resolution for “Screen resolution”.
7. Click the “OK” button to close the dialog box.
Note
• During network connection, the screen resolution can be set using the setting icon in the task tray. For details, refer to the
NetDA Manager User’s Manual (on the CD-ROM).