Dyconn WA502S User manual

Page
2
Articulating TV/Monitor Wall Mount (Butterfly Series)
Model: WA-502S
Instruction Manual
Images may different from actual product
Disclaimer
It is Dyconn’s intention to have all the correct information represented within this manual.
Although we try our best, Dyconn makes no claim that the information comprised herein
covers all conditions or details in connection with installation or use of this product. Dyconn
assumes no responsibility for accuracy or adequacy of information comprised in this
document. The information comprised here is subject to change without notice or obligation
of any kind.
•A warning alerts you to the possibilities of personal injury or damage to equipment
if you do not follow the corresponding instructions. It is installer's responsibility to
make sure all components are properly assembled and installed using the
instructions manual provided.
•Using improper screws or screw size may damage your display. If spacers are
required, be sure to use correct size of screws. Proper screws will easily and
completely thread into the display mounting holes. Inadequate thread
engagement in the display may cause display to fall.
•It is installer’s responsibility to make sure the combined weight of all components
does not exceed weight capacity. Exceeding weight capacities can result in
severe personal injury or damage to equipment. It is installer’s responsibility to
make sure the combined weight of all components does not exceed weight
capacity of 19.8lbs (9Kg).
•Allowing any part of your component cables to be caught between movable parts
can result in serious personal injury or damage to equipment.
Read the following warning before installing
!Verify all parts are included. Do not install if the products or hardware is damage. Not
all hardware included will be used.
!Please contact a qualified installer
!This product contain moving parts, Use with caution
!Determine approximate location for mounting and keeping in mind the display size,
extension, height adjustment and pitch / roll requirements.
!This product contains small item, keep these items away from children

Page
3
!Do not exceed the maximum weight capacity for this product. Exceeding the weight
capacity can result in serious personal injury or damage to equipment!
Specifications
Product Dimension
Weight Capacity
50(LBS) / 22.7(KG)
Suits LCD Flat Panel Displays
13”(330mm)-30”(762mm)
Maximum Extension
18”(457mm)
Depth from Wall
3.2”(81.5mm)
Tilt adjustment
+/- 40 degree
Display Pan Swing- Side to side
+/- 90 degree
Pivot
180 degree
VESA Compatibility
75x75mm/100x100mm and 200x100mm

Page
4
Supplied Parts

Page
5
Required Tools
ASSEMBLY and INSTALLATION
INSPECT THE MOUNT BEFORE ASSEMBLY
1. Carefully inspect/verify that all components are present.
2. If the mount/components are damaged or missing, please contact the company/seller
of the product you purchased and report the issue.
Note: Read all assembly instructions before staring the installation process.

Page
6
Figure 1-1
Step 【1】Wood Wall Installation
Drilling into electrical wires or cables can cause serious personal injury! Always make
certain that area behind mounting area is free of electrical wires and cables before drilling
or installing.
Improper installation can lead to mount falling causing severe personal injury or damage
to equipment. It is installer’s responsibility to make sure the combined weight of all
components does not exceed weight capacity of 19.8lbs (9Kg). The manufacture accepts
no responsibility for incorrect installation.
Wood Wall Installation
1. To determine Wall Plate (2) mounting height, add 1” (25.4mm) to the mounting height
from the table bellow. (See Figure 1-1)
2. Attach the Wall Plate (2) to the wall. Mark location with pencil. (See Figure 1-2)
3. Use awl to find stud location. Ensured that marks are in the center of wood stud. Drill
pilot holes and ensure that pilot holes are straight. (See Figure 1-3)
Wood Pilot
Pilot hole size
Pilot Drill Depth
1/8"
2"
4mm
50mm

Page
7
Figure 1-2
Figure 1-2
4. Insert Philips Screw ST6.3x65mm (3) through Washer (14), Wall Plate (2) and finally
into pilot hole. Repeat for remaining Philips Screws. Tighten Philips Screw securely.
(See Figure 1-4)
Figure 1-4
Figure 1-3

Page
8
Figure 1-5
Step 【1】Masonry Wall Installation
Drilling into electrical wires or cables can cause serious personal injury! Always make
certain that area behind mounting area is free of electrical wires and cables before drilling
or installing.
Improper installation can lead to mount falling causing severe personal injury or damage
to equipment. It is installer’s responsibility to make sure the combined weight of all
components does not exceed weight capacity of 19.8lbs (9Kg). The manufacture accepts
no responsibility for incorrect installation.
Note: Select correct hardware that fits your application
Masonry Wall Installation
1. To determine Wall Plate (2) mounting height, add 1” (25.4mm) to the mounting height
from the table. (See Figure 1-5)
2. Attach the Wall Plate (2) to the wall. Mark the mounting location. (See Figure 1-6)
3. Drill the concrete holes and ensure the pilot holes are straight and completely through
concrete wall. (See Figure 1-7)
Masonry Pilot
Pilot hole size
Pilot Drill Depth
5/16"
2.36"
10mm
60mm

Page
9
Figure 1-6
Figure 1-7
4. Insert Anchor (13)into anchor hole and seat with gentle tapping from hammer. Anchor
(13)should be fully engaged into concrete wall. Tighten anchor screw until anchor has
fully collapsed against back side of concrete wall. (See Figure 1-8)
Figure 1-8

Page
10
5. Insert Philips Screw ST6.3x65mm (3) through Washer (14), Wall Plate (2) and finally
into pilot hole. Repeat for remaining Philips Screws. Tighten Philips Screws securely.
(See Figure 1-9)
Figure 1-9

Page
11
Figure 2-1
Step 【2】Display Installation
Using improper screws or screw size may damage your display. If spacers are required,
be sure to use correct size of screws. Proper screws will easily and completely thread into
the display mounting holes. Inadequate thread engagement in the display may cause
display to fall.
It is installer’s responsibility to make sure the combined weight of all components does not
exceed weight capacity. Exceeding weight capacities can result in severe personal injury
or damage to equipment. It is installer’s responsibility to make sure the combined weight
of all components does not exceed weight capacity of 19.8lbs (9Kg)
Wall Mount LCD Arm will only work when a display is properly installed.
Note: All Spacers or Screws used should be the same length.
Attaching the Display
1. Ensure Tilter Mount Bracket of Wall Mount LCD Arm Assembly is able to swivel and
tilt easily. (See Figure 2-1) Adjust as required before proceeding to next step.
2. Carefully place the display face down on protective surface.(See Figure 2-2)
Figure 2-2

Page
12
Figure 2-4
3. Determine depth of recessed mounting holes relative to back of surface of display.
4. Select proper length of Screws (6、8) place the Spacers (4) on the back of display,
follow by position and orient the mounting holes in the Tilter Mount Bracket so that the
mounting holes on the Tilter Mount Bracket and Spacers (4) are aligned. (See Figure
2-3)
5. Using Philip Screwdriver, install selected Screws (6、8) through mounting holes on Tilter
Mount Bracket and Spacers (4), finally into the display monitor. Tighten Screws with
Philip Screwdriver so the Tilter Mount Bracket is firmly attached to the display monitor.
Do not over tighten the Screws. Stop immediately if you encounter any resistance.
(See Figure 2-4)
Figure 2-3

Page
13
Step 【3】Attaching Wall Mount LCD Arm Assembly
Wall Mount LCD Arm will only work when a display is properly installed.
Attaching the LCD Arm Assembly
1. Attach the Wall Mount LCD Arm Assembly (1) to Wall Plate (2) by inserting the LCD
Arm Assembly downward, into the top of the Wall Plate pole. (See Figure 3-1)
2. Once you have Wall Mount LCD Arm Assembly is in desired position, tighten with Hex
Grub Screw using Hex Allen Wrench 2.5mm (10) provided so the assembly is firmly in
place. (See Figure 3-2)
Figure 3-1
Figure 3-2

Page
14
Figure 3-3
3. Place the Cover (11) and tighten with Phillips Screw M6x12mm (12) through Plastic
Washer (15) using a Phillip Screwdriver. Do not over tighten. This is to prevent the
LCD Arm Assembly to be lift unnecessary. (See Figure 3-3)

Page
15
Step 【4】Cable Management
Ensure the Wall Mount LCD Arm Assembly is fully extended before connecting cables.
Exercise caution when attaching or removing the display to avoid personal injury or
damage to equipment. Disconnect power before removing the display.
Note: Ensure enough slack in the cables to allow for movement of the Arms.
Installing Cable Management
1. Connect cables to display monitor. Position the display at its highest place to
make sure that there is enough cabling at the end of the Arms so that the cables
are not stretched or pulled out when the display is moved. (See Figure 4-1)
2. Feed the cables by pushing the cables into cable bracket entry slot on the underside
of the Arms as shown. (See Figure 4-2)
Figure 4-1
Figure 4-2

Page
16
Figure 5-1
Step 【5】Adjusting the Display Monitor
Forced movement of Mount Bracket without loosening the Screws will damage Wall
Mount LCD Arms Assembly or display monitor.
Exercise caution when adjusting the display, to support the display to avoid damage to
equipment. Disconnect power before removing the display.
Adjusting the Wall Mount LCD Arm Assembly Resistance
1. To support display monitor when adjusting resistance of the Wall Mount LCD Arm
Assembly. (See Figure 5-1)
Adjusting the Mount Bracket Resistance
2. Our Product is brilliantly engineered to control the resistance in the Tilter Mount
Bracket to suit your display swing side to side of 90 degree and tilt forward and
backward of 40 degree. It is possible to control the amount of resistance in the Tilter
Mount Bracket to suit your display monitor.
3. Referring to the weight of the display monitor. If the Tilter Mount Bracket tends to
automatically fall, it may be required to adjust the Tilter Mount Bracket joint to suit your
display monitor tilt place of forward and backward of 40 degree. This can be done by
using Hex Allen Wrench 4mm (9) supplied, to increase the resistant of the Tilter Mount
Bracket to secure tilt place, adjust the M5x15mm Tension Hex Socket Cap Screw
located around the Tilter Mount Bracket using the supplied 4mm Hex Allen Wrench.
(See Figure 5-2)

Page
17
4. To increase or decrease the resistance of the Pivot Joint to suit display monitor swing
side to side, adjust the Tension Hex Cap Screw on front side of the Wall Mount LCD
Arm to secure the place. (See Figure 5-3)
5. To increase the resistance, tighten the M5x15mm Tension Hex Socket Cap Screw
using Allen Wrench 4mm (9) supplied in a clockwise direction. To decrease the
resistance, loosen the M5x15mm Tension Hex Socket Cap Screw using Allen Wrench
4mm (9) supplied in an anti-clockwise direction.
Figure 5-2
Figure 5-3

Page
18
6. This product is designed to adjust quickly and easily according to your needs. To
adjust the height, remove the Extension Arm from Wall Plate (2) follow by attaching
the LCD Arm to achieve your desired position. (See Figure 5-4)
7. If this product tends to automatically move to side, it may be required adjustment on
the LCD Arm to suit your display monitor arm swing to side position. This can be done
by using Hex Allen Wrench 2.5mm (10) supplied. (See Figure 5-5)
Figure 5-4
Figure 5-5

Page
19
Figure 6-1
Step 【6】Ergonomic Guidelines
Note: Proper ergonomic design is necessary to prevent repetitive strain injuries, which
can develop over time and can lead to long-term disability
1. Ensure the correct focal distance for ultimate visual comfort. For visual comfort, a viewing
distance between 460mm (18”) to 610mm (24”) is recommended. (See Figure6-1)
Figure6-1

Page
20
Figure 6-2
2. To assess the fit between a person and their work, ergonomics recommended that the
optimal of your screen position should be slightly below eye level. Viewing angle should
be approximately 10°-20° downward of the screen’s center. The lumbar (bottom five
vertebrate in the spine) needs to be supported to decrease disc pressure. Providing both
a seat back that inclines backwards and has a lumbar support is critical to prevent
excessive low back pressures. The combination which minimizes pressure are
recommended on seating ergonomic which the wrist angle must be straight, seat angle
and knee angle must be on 90° angle. Angular adjustment to reduce reflection on your
monitor. The range should be between 5° forward tilt to 15° backward tilt. (See Figure6-2)
Figure6-2