Dyconn Butterfly Series User manual

t

Page 2
Articulating TV/Monitor Grommet/Clamp Desk Mount
Model: DE300S (Butterfly Series)
Instruction Manual
Images may different from actual product
Disclaimer
It is Dyconn’s intention to have all the correct information present within this manual. Although we try
our best, Dyconn makes no claim that the information comprised herein covers all conditions or details
in connection with installation or use of this product. Dyconn assumes no responsibility for accuracy or
adequacy of information comprised in this document. The information comprised here is subject to
change without notice or obligation of any kind.
•This warning informs you of the possibilities of personal injury or damage to equipment if you
do not follow the corresponding instructions. It is the installer's responsibility to make sure all
components are properly assembled and installed using the instruction manual provided.
•Using improper screws or screw size may damage your display. If spacers are required, be
sure to use screws of the correct size. Proper screws will easily and completely thread into
the display mounting holes. Inadequate thread engagement in the display may cause display
to fall.
•It is the installer’s responsibility to make sure the combined weight of all components does not
exceed the weight capacity of 17.6lbs (8kg). Exceeding weight capacity can result in severe
personal injury or damage to equipment.
•Allowing any part of your component cables to be caught between movable parts can result in
serious personal injury or damage to equipment.
•The table being used for installation must be stable and strong enough to support the DE300S
mount and display.

Page 3
Please read the following warnings before installing:
zVerify that all parts are included. Do not install if the products or hardware are damaged. Not all
hardware included will be used.
zPlease contact a qualified installer.
zThis product contains moving parts. Use with caution.
zDetermine approximate location for mounting and be sure to consider the display size, extension,
height adjustment and pitch/roll requirements.
zThis product contains small items; please keep these items away from children.
zDo not exceed the maximum weight capacity for this product. Exceeding the weight capacity can
result in serious personal injury or damage to equipment!
Specifications
Weight Capacity 17.6lbs (8kg)
Suits LCD Flat Panel Displays 12”(300mm)-24”(610mm)
Maximum Extension 11.2”(285mm)
Depth from Pole (Closed) 2.3”(57.5mm)
Tilt adjustment +/- 90 degrees
Display Swivel +/- 90 degrees
Pivot (Desk / Display / Arm) 360 / 180 /360 degrees
Maximum Mounting Surface Thickness 3”(75mm)
VESA Compatibility 75x75mm and 100x100mm

Page 4
Product Dimension

Page 5
Supplied Parts

Page 6
Required Tools
ASSEMBLY and INSTALLATION
INSPECT THE MOUNT BEFORE ASSEMBLY
1. Carefully inspect/verify that all components are present.
2. If the mount/components are damaged or missing, please contact the company/seller of the
product you purchased this unit from and report the issue.
Note: Read all assembly instructions before starting the installation process.

Page 7
Step 【1】Installation of Desk Clamp
Using improper screws or screw size may damage your display. If spacers are required, be sure to
use screws of the correct size. Proper screws will easily and completely thread into the display
mounting holes. Inadequate thread engagement in the display may cause display to fall.
Note: Other tools may be required depending on your method of installation.
Note: It is recommended that the DE300S mount be clamped to the side edge or rear of the desktop
surface. The DE300S mount is suitable for square edged desk only. It is the installer’s responsibility to
make sure the desktop structure to which this product is attached can support the combined weight of
all components.
Installation to Desk
1. Adjust the height of the Desk Clamp (2) to suit desktop surface (See Figure 1-1).
2. Place the Plastic Gasket Cushions as shown (See Figure 1-2).
Figure 1-1
Figure 1-2

Page 8
3. Attach the Desk Clamp (2) on to the edge of the desk in the desired position and with the clamp
opening facing towards the edge of desktop (See Figure 1-3). Tighten by hand to ensure that the
Desk Clamp fully clamps to the desktop surface and is secure (See Figure 1-4).
4. To position the Collar at your desired height, you will need to loosen the Collar as shown. Tighten
by hand until the Collar is firmly in place (See Figure 1-5).
Figure 1-3 Figure 1-4
Figure 1-5

Page 9
Figure 1-6
Figure 1-7
Step 【1】Installation of Grommet Clamp
Using improper screws or screw size may damage your display. If spacers are required, be sure to
use screws of the correct size. Proper screws will easily and completely thread into the display
mounting holes. Inadequate thread engagement in the display may cause display to fall.
Note: Other tools may be required depending on your method of installation.
Installation of Grommet Clamp to Desk
5. Remove the metal plate from DMG-01 (See Figure 1-6).
6. Attach the metal plate to the base of the pole. Thread the Hex Screws M6x8mm into the metal
plate using the Allen Wrench 4mm (9) as shown (See Figure 1-7).

Page 10
Figure 1-10
Figure 1-8
Figure 1-9
7. Place the Plastic Gasket Cushions on the metal plate and base as shown (See Figure 1-8).
8. Attach the Grommet Clamp Pole (2) to the edge of the desk in the desired position and ensure
that there is sufficient cabling in the desktop hole as shown (See Figure 1-9).
9. Tighten by hand to ensure that the Grommet Clamp pressure plate is pressed flat onto the desk
surface and is secure (See Figure 1-10).

Page 11
10. To position the Collar at your desired height, you will need to loosen the Collar as shown. Tighten
by hand in a clockwise direction until the Collar is firmly in place (See Figure 1-11).
Figure 1-11

Page 12
Figure 2-2
Step 【2】Display Installation
Using of improper screw size may damage your display. If spacers are required, be sure to use
correct size of screws. Proper screws used will easily and completely thread into the display mounting
holes. Inadequate thread engagement in the display may cause display falling.
It is the installer’s responsibility to make sure the combined weight of all components does not exceed
the weight capacity of 17.6lbs (8kg). Exceeding weight capacity can result in severe personal injury or
damage to equipment.
The DE300S assembly will only work when a display is properly installed.
Attaching the Display
1. Ensure that the Tilter Mount Bracket of the arm is able to swivel and tilt easily (See Figure 2-1).
Adjust if necessary before proceeding to the next step.
2. Carefully place the display face down on protective surface (See Figure 2-2).
Figure 2-1

Page 13
3. Determine depth of recessed mounting holes relative to the surface on the back of the display.
4. Align the Spacers (4) with the holes on the back of the display. Then, align the Tilter Mount Bracket
mounting holes with the Spacers (4). Thread the Screws M4x25mm (6) through the Tilter Mount
Bracket, Spacers and into the display (See Figure 2-3).
5．Using a Philips Screwdriver, tighten the screws so the Tilter Mount Bracket is firmly attached to
the display monitor. Do not over tighten the screws. Stop immediately if you encounter any
resistance (See Figure 2-4).
Note: All Spacers or Screws used should be the same length.
Figure 2-3
Figure 2-4

Page 14
Step 【3】Articulating TV/Monitor Grommet/Clamp Desk Mount
The DE300S assembly will only work when a display is properly installed.
Attaching the DE300S Arm Assembly
1. Attach the assembled arm (1) down onto the pole as shown (See Figure 3-1).
2. Once you have the assembled arm in your desired position, tighten the Hex Grub Screw using the
Hex Allen Wrench 2.5mm (7) until the arm is firmly in place (See Figure 3-2).
Figure 3-1
Figure 3-2

Page 15
Step 【4】Cable Management
Ensure the DE300S mount is fully extended before connecting the cables.
Exercise caution when attaching or removing the display to avoid personal injury or damage to
equipment. Disconnect power before removing the display.
Note: Be sure to leave enough slack in the cables to allow for movement of the arms.
Installing the Cables
1. Connect cables to the display monitor. Fully extend the arm to ensure that there is sufficient cabling
at the end of the arms so that the cables are not stretched or pulled out when the display is moved
(See Figure 4-1).
Figure 4-1

Page 16
2. Feed the cables through the cable bracket slot on the underside of the arm as shown (See Figure
4-2).
3. Attach the Cable Clip (3) to secure the cables to the pole (See Figure 4-3).
Figure 4-2
Figure 4-3

Page 17
Step 【5】Adjusting the Display Monitor
Forced movement without loosening the Screws will damage the DE300S mount or display monitor.
Exercise caution when adjusting the display. Support the display to avoid damage to equipment.
Disconnect power before removing the display.
Note: The DE300S mount comes factory set to support 17.6 lbs (8kg) displays. Adjust the DE300S
mount to suit the weight of your displays.
Adjusting the DE300S Mount Resistance
1. The DE300S mount is engineered to control the resistance in the Tilter Mount Bracket to suit your
display swivel of +/- 90 degrees and tilt of +/- 90 degrees. You can easily control the amount of
resistance in the Tilter Mount Bracket to suit your display monitor.
2. Support display monitor when adjusting resistance of the LCD Arm Assembly (See Figure 5-1).
Figure 5-1

Page 18
Figure 5-2
3. If the weight of the display monitor causes the Tilter Mount Bracket to fall, you may need to adjust
the Tilter Mount Bracket joint to suit your display monitor tilt position of +/- 90 degrees. This can
be done by using Hex Allen Wrench 4mm (9). To increase the resistance of the Tilter Mount
Bracket to secure tilt position, adjust the Tension Hex Socket Cap Screw M5x15mm located
around the Tilter Mount Bracket Joint using the 4mm Hex Allen Wrench (See Figure 5-2).
4. To increase or decrease the resistance of the Pivot Joint to suit display monitor swivel, adjust the
Tension Hex Socket Cap Screw M5x15mm located on the Tilter Mount Bracket Joint to secure the
position (See Figure 5-3).
5. To increase the resistance, tighten the M5x15mm Tension Hex Socket Cap Screw using Allen
Wrench 4mm (9) in a clockwise direction. To decrease the resistance, loosen the M5x15mm
Tension Hex Socket Cap Screw using Allen Wrench 4mm (9) in a counterclockwise direction.
Figure 5-3

Page 19
6. The DE300S mount is manufactured and designed to adjust quickly and easily according to your
needs. To adjust the height, loosen Collar to raise or lower the LCD Arm assembly to achieve your
desired position (See Figure 5-4).
7. If this product tends to drift to the side, you may need to adjust the tension on the arm to suit your
display monitor arm to the desired position. This can be done by using Hex Allen Wrench 2.5mm
(7) (See Figure 5-5).
Figure 5-4
Figure 5-5

Page 20
Step 【6】Ergonomic Guidelines
Note: Proper ergonomic design is necessary to prevent repetitive strain injuries, which can develop
over time and can lead to long-term disabilities.
1. To ensure the correct focal distance for ultimate visual comfort, a viewing distance between 460mm
(18”) to 610mm (24”) is recommended (See Figure6-1).
Figure 6-1