Dynabrade 52715 Guide

                         
                      
1Hp Cone or Plug Grinder
Governor Controlled
   ! ! " # $ % & $ " ' ( $ ) * + , - . / *  $ +  ! % $ % 0 # $  % + * % $ % 1 *
Models:
52715 – 12,000 RPM
52716 – 15,000 RPM
52717 – 18,000 RPM
52718 – 20,000 RPM
SAFETY LEGEND
WARNIN
G
WARNING
2 3 4 5 4 6 5 7 6 5 3 8 9 : 4 6 5 : ; ; < = 4 6 7 4 < : ; 8 3 5 7 > 3 8 ? 9 @
; A ? 6 B 7 8 C : ; ; D 3 8 4 : ; 8 E F ? 9 ? : ; 8 9 E 4 6 5 : ; ; < G
WARNING
H I J K L M N J O N P M Q R S T N U J V M L Q W N W X X N P R J T Y J I J
K L M N J O N P M Q N M O M Q Z M L R N M [ \ ] ^ _ ` a b c b
WARNING
d e f g h i j k l i m g i l k e n k h l o k l p e q f e r s t e o e u g l f e r
k l n l o k j v h o j o k f k t j k e u n e e r k t e j g g w h n j p w e
k t i e f t l w r w h v h k x j w q e f i e y q h i e r p m w j s z
WARNING
{ | } ~   ~   }     |     |          |  }   |  
 }    |    | }    |   }           | }            |
          ~    }  ~      |  |    
WARNING
 } |  |    ~           |            |         
  ~                }     ~ }        | }     }    |
  ~ }    }       |    }  ~   }     | |     }      
WARNING
       ¡ ¢ £ ¢  ¤ ¥ ¦   § § ¨   £  ¤ § ¨ ¦ ¦  ©     § ¢  ¤ ª   «  ¬  
¡  §  § ® ¢  ® ¢ ¨ §  §     ¨ §   ¯ ¨  © ° ±    ² ¨ §  ¤ ¢ ³ ´
¢ µ  ¤ ¥ ª  ¢ ©  ¤   ¤  ²      ¢ ²  ¤ ¢   ¡  §  § ¢  ¤ ª  ² ²   µ § °
¶  }  }       |   }            }   }      |     | }        | }  |            }    }     |       |     |    ~          | }       |    ·
   }      }  }  ¸ } ~    } |  }   ¹   }      | }         ~  }    }    }             } ~ ~  |  }  ~         ¹   |  ~ }  º }     }   }    
»         ¼ ¹ º  » ½  }     ¾      | {  |  }    ¹  | ¿     À Á Â Ã Ä  Â    | }        }   }         |  }      |    |    }     ¶     |         |   
Å    ¾ } |  }   { |    ~       ¹  | }           À ¹ º  » Á Æ  Â  ¾          | }  ¶     }     À ¾  ¶ Ç È { } |  Â È Â É    |    }  ¾           |
  }   } |   ¼  º ½ Ê }   Ê    º   ·    ~  |  ~ {    | ¿     À  }     ¶     |       }   }     ~ }      }   }   Ë  ~ }  ¶     }      
SAFETY INSTRUCTIONS
Carefully Read all instructions before operating or servicing any Dynabrade®Abrasive Power Tool.
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written consent from Dynabrade, Inc.
Tool Intent: Cone or Plug Grinders are ideal for smoothing weld seams, cleaning castings and preparing surfaces for plating or painting.
Do Not Use Tool For Anything Other Than Its Intended Applications.
Training: Proper care, maintenance, and storage of your tool will maximize its performance.
• Employer's Responsibility – Provide cone or plug grinder operators with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.
• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
• Mount only recommended accessories. See back page of manual and Dynabrade catalog.
• Follow tool specifications before choosing size and type of accessory.
• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG (10 bars, g) or 150
percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
• DO NOT use – cut off wheels or router bits.
OPERATING INSTRUCTIONS
Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.
(Continued on next page.)
] [ Ì H Í Î ^ ] Ï Ð Ñ Ò Ó H \ Í Y H Ï Ò Ñ [ Í H [ Ô Ô Õ H Ö ] Ð \ \ H Ô

To Tool Station
Closed Loop Pipe System
(Sloped in the direction of air flow)
Ball
Valve
Ball
Valve
Filter
Coupler
Regulator
Lubricator
Air Flow
Drain
Valve
Drain
Valve
Air Tool Air Compressor
and Receiver
Drain Valve
Air Hose
90 PSIG MAX
(6.2 Bar)
Air Flow
Refrigerated
Air Dryer
2
Filter
Regulator
Lubricator
90 PSIG
(6.2 Bar)
OPERATING INSTRUCTIONS (continued)
Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
• Keep hand and clothing away from working end of the air tool.
Operation: Be sure that any loose clothing, hair and all jewelry is properly restrained.
• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.
• Check tool RPM (speed) with tachometer with air pressure set at 90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool
housing, or operating improperly, the tool must be serviced and corrected before use.
Caution: Tool RPM must never exceed abrasive/accessory RPM rating. Check accessory manufacturer for details on maximum operating speed or special
mounting instructions.
• With power source disconnected from air tool, mount types 16, 17, 18, 18R and 19 Cone and plug wheels onto 3/8"-24 UNF-2A Spindle thread.
• Connect air tool to power source. Be careful NOT to depress throttle lever in the process. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).
Caution: After installing the accessory, before testing or use and/or after assembling tool, the cone or plug grinder must be started at a reduced speed to check for good
balance. Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation.
• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.
• Use a vise or clamping device to hold work piece firmly in place.
• Do not apply excessive force on tool or apply “rough” treatment to it.
• Always work with a firm footing, posture and proper lighting.
Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.
Air System
c
DROP/MIN.
c ×
SCFM
LUBRICATOR SETTING
CONE or PLUG MOUNTING
Typical Mounting for Cone or Plug Wheels
• Dynabrade Air Power Tools are designed to
operate at 90 PSIG (6.2 Bar/620 kPa) maximum
air pressure at the tool inlet, when the tool is
running. Use recommended regulator to control
air pressure.
• Ideally the air supply should be free from moisture.
Incorporating a refrigerated air dryer after the
compressor and drain valves at each tool station
(as shown) further reduces moisture from
condensation in the air supply.
• Blotters must cover at least the adapter surface as shown.
• A blotter (compressible washer) shall always be used between the
abrasive cone or plug surface and the adapter to ensure uniform
distribution of pressure.
• Blotters shall cover the entire adapter contact area.
• New blotters shall be used each time a wheel is mounted unless blotters
are affixed to the cone or plug by the manufacturer.
Cone or Plug
Spindle is shorter than hole providing proper clearance.
Blotter
Driving Flange
with Flat Bearing Surface
Spindle
Adapter

Maintenance Instructions
Important: A Preventative Maintenance Program is recommended whenever portable grinders are used.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model# , Serial# and RPM of your air tool.
• All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties. Dynabrade recommends the following:
11411 Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminants. Operates 55
SCFM/1,558 LPM @ 90 PSIG with 1/2" NPT female ports.
• Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 4 drops per minute). Dynabrade Air Lube (P/N 95842 : 1 pt 473 ml) is recommended.
Routine Preventative Maintenance: Check free speed of cone or plug grinder using a tachometer. This governor controlled grinder should be speed
checked every 20 hours of use or weekly, whichever occurs more frequently.
• DO NOT disassemble the governor for any reason. Reorder correct speed – governor assembly (See Assembly Breakdown) and recheck free speed of
tool with a tachometer.
• Periodically remove the accessory and clean the adapter for debris to keep accessories secure and reduce vibration.
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40®).
• A Motor Tune-Up Kit (P/N 96532 ) is available which includes high wear and medium wear motor parts.
• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. (See Assembly Breakdown)
• Blow air supply hose out prior to initial use.
• DO NOT carry tool by air hose or near the tool throttle lever.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903 ) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842 ) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
• Use of tool rests, hangers and/or balancers is recommended.
• Protect tool inlet from debris. (See Notice Below)
• DO NOT carry tool by air hose or near the tool throttle lever.
• Protect cone and plugs from exposure to water, solvents, high humidity, freezing temperatures and extreme temperature changes.
• DO NOT USE cone or plugs that have been dropped or show signs of cracks, nicks or other defects.
• Store accessories in protective racks or compartments to prevent damage.
Machine Specifications
3
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Model Motor Motor Sound Maximum Air Flow Spindle Air Pressure Weight Length Height
Number HP (W) RPM Level CFM/SCFM (LPM) Thread PSIG (Bars) Pound (kg) Inch (mm) Inch (mm)
52715 1 (744) 12,000 82 dB(A) 5/38 (1,076) 3/8"-24 male 90 (6.2) 1.9 (.9) 7-3/4 (198) 1-7/8 (48)
52716 1 (744) 15,000 83 dB(A) 5/39 (1,104) 3/8"-24 male 90 (6.2) 1.9 (.9) 7-3/4 (198) 1-7/8 (48)
52717 1 (744) 18,000 84 dB(A) 6/40 (1,133) 3/8"-24 male 90 (6.2) 1.9 (.9) 7-3/4 (198) 1-7/8 (48)
52718 1 (744) 20,000 88 dB(A) 6/40 (1,133) 3/8"-24 male 90 (6.2) 1.9 (.9) 7-3/4 (198) 1-7/8 (48)
Additional Specifications: Air Inlet Thread 3/8" NPT • Hose Size 3/8" (10 mm) • Air Flow Rate Based At Max HP. • Air Pressure 90 PSIG Max
(PD01•83)

4
1 51947 Housing Cover
2 96498 Wave Spring
3 95438 O-Ring
4 53620 Motor Adapter
5 53610 Adapter
6 54520 Bearing
7 51951 Shim Pack
8 51922 Front Bearing Plate
9 96441 Pin (2)
10 51927 Rotor Spacer
11 51921 Rotor
12 51926 Blade (4/pkg.)
13 51925 Cylinder
14 51923 Rear Bearing Plate
15 02057 Bearing
16 96445 Pin (2)
17 51924 Gasket
18 Governor Assembly
51930 12,000 RPM
51931 15,000 RPM
51932 18,000 RPM
51933 20,000 RPM
19 96444 Pin
20 51949 Safety Lever Assembly
21 51946 Valve Stem Assembly
(Incl. 96443 O-Ring)
22 53738 Housing – Model 52715
53739 Housing – Model 52716
53740 Housing – Model 52717
53741 Housing – Model 52718
23 51945 Valve Seat
24 51942 Baffle
25 51941 Spring
26 51944 Tip Valve
27 51943 Spring
28 96442 O-Ring
29 51940 Spacer
30 51939 Silencer Plate
31 51937 Inlet Bushing
(Incl. 2 – 51938 Screens)
Ø Ù Ú Û Ü Ý Û Þ
No. Part # Description
34 00001180 Warning Label
35 00001181 Specification Label
ßàáÛ â Ý Û Þ
No. Part # Description
1
67
89
10 12
11
13
23 24 25 26 27 28 29 30 31
19
33
22 32
9
14
16
15
17
20
21
2
Adhesive: A8= Loctite #567
A10 = Loctite #243
Torque: N•m x 8.85 = In. - lbs.
Oil: O1= Air Lube
O
O1
A10
A8
A
T
KEY
34
35 N•m
T
17 N•m
T
35 N•m
T
2 N•m
T
A10
O1
18
1 Hp Cone or Plug Wheel Grinder
Complete Assembly Breakdown
Left Hand Threads
5

Disassembly Instructions - 1 Hp Cone or Plug Grinders
Important: Manufacturer’s warranty is void if tool is disassembled before warranty expires.
1. Secure front end of housing in a soft (aluminum or bronze jaw) vise, align the vise jaws with machined flat on the silver ring.
2. Using 50971 Pin Wrench ( order separately ) or an adjustable pin wrench, remove 51947 Housing Motor Cover.
3. Remove remaining assembly from vise.
4. Remove 96498 Wave Spring.
5. Pull Motor Assembly from housing assembly, and remove 53620 Motor Adapter with 95438 O-Ring.
6. Remove Governor Assembly by using a slotted screw driver. ( LEFT HAND thread)
7. Secure 51925 Cylinder and place a 1/8" (3 mm) drift pin to the base of the internal thread and press the 51921 Rotor from
the 02057 Rear Bearing.
8. Slide 02057 Rear Bearing from 51923 Rear Bearing Plate.
9. Remove 51925 Cylinder and 51926 Blades.
10. Secure 51921 Rotor in a soft (aluminum or bronze jaw) vise and remove 53610 Adapter (twist counterclockwise).
11. Slide 51922 Front Bearing Plate and 51927 Rotor Spacer from 51921 Rotor.
12. Slide 54520 Bearing and shims from 51922 Front Bearing Plate.
Motor Disassembly Complete.
1. Secure housing using 51989 Repair Collar ( order separately–see back cover for Optional Accessories ).
2. Remove 51937 Inlet Bushing (twist counterclockwise).
3. Remove 51943 Spring, 96442 O-Ring, 51940 Spacer and 51939 Silencer Plate from 51937 Inlet Bushing.
4. Remove 51941 Spring, 51942 Baffle, 51944 Tip Valve and 51945 Valve Seat.
Disassembly Complete.
Assembly Instructions - 1 Hp Cone or Plug Grinders
Important: Be sure parts are clean and in good repair before assembling. Follow grease, oil and torque specifications.
1. Place 51921 Rotor into a soft (aluminum or bronze jaw) vise with male thread facing upwards.
2. Slip 51927 Rotor Spacer over rotor shaft and down against rotor body face.
3. Press 96441 Coiled Pin into 51922 Front Bearing Plate. Make certain, coiled pin does not protrude beyond
internal bearing surface.
4. Place a .002" Shim into the base of 51922 Front Bearing Plate as an initial spacing and slide 54520 Bearing to the
front plate base.
Note: 51951 Shim Pack contains .001" and .002" Shims.
5. Slip bearing/bearing plate assembly onto rotor, torque 53610 Adapter onto rotor shaft to 17 N•m (150 lb.-in.).
6. Check clearance between rotor and front bearing plate by using a .001" feeler gauge. Clearance should be between
.001" - .0015". Adjust clearance by repeating steps 4 and 5 with different shims if necessary.
7. Once proper rotor gap clearance is achieved, install well lubricated 51926 Blades (4) into rotor slots. Dynabrade
recommends lubricating blades with 95842 Air Lube.
Important: Make certain beveled edge of blade follows rotor outside diameter.
8. Install 51925 Cylinder over rotor and front plate raised boss. Align coiled pin on front plate to cylinder slot.
9. Press 96441 Coiled Pin into blind hole on 51923 Rear Bearing Plate. Press (2) 96445 Coiled Pins into the back side
of rear bearing plate.
(Continued on next page.)
5

Assembly Instructions - (Continued)
Important: Manufacturer’s warranty is void if tool is disassembled before warranty expires.
Please refer to parts breakdown for part identification.
10. Peel backing off 51924 Gasket and align it firmly in place onto 51923 Rear Bearing Plate.
11. Place 51923 Rear Bearing Plate over rotor mandrel and insert raised boss on rear bearing plate into cylinder diameter, while
inserting short coiled pin into cylinder slot. Be sure inlet slot on rear bearing plate line up with inlet slot on cylinder. Flip
cylinder end to end and repeat steps 8 & 9 for correct assembly.
12. Press 02057 Bearing onto rotor and into 51923 Rear Bearing Plate hole until it is seated.
Important: While pressing 02057 Bearing, make certain to contact inner race of bearing only. Cylinder must fit snug
between bearing plates. If too tight, rotor will not turn freely. Rotor must be lightly tapped at press fit end until rotor spins
freely while still maintaining a snug fit. A loose fit will not achieve the proper preload on motor bearings.
13. Add one drop of Loctite®243 (or equiv.) to governor assembly male thread and screw governor assembly into place (
LEFT
HAND thread) with a slotted screw head. Torque to 2 N•m (18 lb.-in.).
14. Install motor assembly into housing, making sure motor drops all the way into housing. Note: Align both 96445 Coiled Pins
to slots in insert and against 51924 Gasket.
15. Install 95438 O-Ring onto 53620 Adapter and slide adapter into housing and over 54520 Bearing.
16. Place 96498 Wave Washer onto 53620 Adapter.
17. Apply a small amount of Loctite®567 to housing thread, and install
51947 Housing Cover using 50971 Pin Wrench (
ordered
separately ) or an adjustable pin wrench. Torque cover to 35 N•m (310 lb.-in.).
Motor Assembly Complete.
1. Secure housing using 51989 Repair Collar ( see back cover for Optional Accessories ) with spindle facing down.
2. Install 51945 Valve Seat by aligning 3 male prongs with three deep slots on insert. Make certain valve seat is pressed flat
against base of pocket.
Note: Add a few drops of Dynabrade Air Lube (P/N 95842 ) to pocket walls before inserting 51945 Valve Seal.
3. Install 51944 Tip Valve as shown.
4. Slide 51942 Baffle into housing long end in first, and place 51941 Spring into shallow wall end of baffle.
5. Pre-assemble 51937 Inlet Bushing by sliding 51939 Silencer Plate, 51940 Spacer over male thread and set 96442 O-Ring
into groove at the base of thread. Slide 51943 Spring into bushing and up to the two 51938 Screens.
6. Apply one drop of Loctite®243 (or equiv.) to
51937 Inlet Bushing thread.
7. Align small inside diameter of 51943 Spring to cone point on 51944 Tip Valve and thread 51937 Inlet Bushing and sub-
assembly into place. Torque bushing to 35 N•m (310 lb.-in.).
8. Slide 96443 O-Ring onto 51946 Valve Stem and slide sub-assembly until o-ring passes through housing hole. Make certain
valve stem assembly slides freely after the o-ring passes through the hole.
9. Remove housing from 51989 Repair Collar and place repair collar onto the bench top with the part number identifier against
the bench. Align the throttle lever holes to housing pin hole and rest the housing and throttle lever onto the legs of the repair
collar. Press 96444 Coiled Pin into lever hole and center into housing.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Before operating, places 2-3 drops of Dynabrade Air Lube (P/N 95842 ) directly into inlet with throttle lever
depressed. Operate tool for 30 seconds to allow Air Lube to properly lubricate internal motor components. Motor should now be
tested for proper operation at 90 PSIG max. If tool operates at a higher RPM than marked on the tool or if vibration and sound
levels seem abnormal, the tool should be serviced to correct the cause before use.
Loctite®is a registered trademark of Loctite Corp.
6

This service chart is published as a guide to expectant life of component parts. The replacement levels are based on average tool
usage over one year. Dynabrade Inc. considers one year usage to be 1,000 hours or 50% of a man year. Parts included in motor
tune-up kit are identified by High Wear and Medium Wear items.
Parts Common to all Models:
Preventative Maintenance Schedule
ã ä å æ ç ç è é ê ë ä ì í ä å î ç ï ð ñ å ò ì ó í å ô
LEGEND
X Type of wear, no other
comments apply.
L Easily lost. Care during
assembly/disassembly.
D Easily damaged during
assembly/disassembly.
R1 Replace each time tool is
disassembled.
R2 Replace each second
time tool is disassembled.
Note: Please refer to page 4 of tool manual for specific part number.
Index Part Description Number High Wear Medium Wear Low Wear Non-Wear
# Number Required 100% 70% 30% 10%
1 51947 Housing Cover 1 X
2 96498 Wave Spring 1 X
3 95438 O-Ring 1 L
4 53620 Motor Adapter 1 X
5 53610 Adapter 1 X
6 54520 Bearing 1 X
7 51951 Shim Pack 1 L
8 51922 Front Bearing Plate 1 X
9 51927 Rotor Spacer 1 X
10 51921 Rotor 1 X
11 51926 Blade (4/pkg.) 4 X
12 96441 Pin (2) 2 X
13 51925 Cylinder 1 X
14 51923 Rear Bearing Plate 1 X
15 02057 Bearing 1 X
16 96445 Pin (2) 2 X
17 51924 Gasket 1 X
18 Governor Assembly
51930 12,000 RPM 1 X
51931 15,000 RPM 1 X
51932 18,000 RPM 1 X
51933 20,000 RPM 1 X
19 96444 Pin 1 L
20 51948 Throttle Lever 1 X
51949 Safety Lever Assembly 1 X
21
51946 Valve Stem Assembly 1
X
(Incl. 96443 O-Ring)
22
See Note Housing 1 X
23 51945 Valve Seat 1 X
24 51942 Baffle 1 X
25 51941 Spring 1 X
26 51944 Tip Valve 1 X
27 51943 Spring 1 X
28 96442 O-Ring 1 L
29 51940 Spacer 1 X
30 51939 Silencer Plate 1 X
31 51937 Inlet Bushing 1 X
[Incl.(2) 51938 Screens]
7
96532 – 1 Hp. Motor Tune-Up Kit

Tune-Up Kit includes high wear
and medium wear motor parts.

DYNABRADE
õ
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: [phone] • Fax: [phone] • International Fax: [phone]
DYNABRADE EUROPE S.àr.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: [phone] • Fax: [phone]
ö ÷ ø ù ú û ü ú ÷ ý þ ÿ ù   þ      ü ÿ ù  ý ÷ ÿ ù   ú
Visit Our Web Site: www.dynabrade.com Email: [e-mail]
Optional Accessories
96532 Motor Tune-Up Kit

Includes assorted parts to help maintain
and repair motor.
01889 Drop-In Motor

Allows quick and easy replacement.
No motor adjustments needed.
Dynaswivel


Swivels 360° AT TWO PIVOT POINTS allowing the air hose to
drop directly to the floor while providing superb tool handling.
95461 – 3/8" NPT.
51989 Repair Collar

Specially designed collar for use in vise to prevent damage
to valve body of tool during disassembly/assembly.
50971 Lock Ring Tool

Lock Ring Tool has a 3/8 in. square socket
for use with 3/8 in. drive; breaker bar,
ratchet head, or torque wrenches.
Bearing Press Tools

Used to install bearings.
96243: For installing 02057 Bearing.
96244: For installing 01007 & 54520 Bearings.
53621 Over Hose Assembly

Over Hose Assembly directs exhaust
away from operator.

50010 – 1/4" Collet Assembly.

50015 – 6 mm Collet Assembly.
Dynabrade Air Lube

Formulated for pneumatic equipment.

Absorbs up to 10% of its weight in water.

Prevents rust and formation of sludge.

Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 m)
95843: 1gal. (3.8 L)
Collet Inserts

50065 – 1/8"

50013 – 1/4"

50014 – 3/8"

50016 – 6 mm

50039 – 8 mm
Carbide Burr Kits

Includes 12 burrs for grinding,
deburring and finishing metal.
93351 – 1/8" Kit
93350 – 1/4" Kit
93380 – 6 mm Kit
Reference Contact Information
1. American National Safety Institute – ANSI
11 West 42nd Street
New York, NY 10036
Tel: [phone]
2. Government Printing Office – GPO
Superintendent of Documents
Attn. New Orders
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: [phone]
3. European Committee for Standardization
Rue de Stassart 36
B - 1050 Brussels, Belgium
30335 Air Supply Hose

3/8 in. I.D. x 60 in. Wide air supply
hose, includes: 3/8 in. NPT male and
female threaded fittings.
96005 Male Plug

Provides up to twice the air flow
compared to standard plug design.

Plug has “ported” design to prevent
“starving” of the air tool.
95262 – 14 mm open-end.