Dynabrade Autobrade Red User manual

Air Motor and Machine Parts
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes
and regulations. Please refer to Dynabrade’s Warning/Safety Operating Instructions for more complete safety information.
WARNING
!
Model:
18062
Parts Page Reorder No. APD00•04
Effective April, 2000
1/2" Impact Wrench
Free Speed 7,000 RPM
Air Tools For The Body Shop
AUTOMOTIVE
Index Key
No. Part # Description
118709 Air Reg. Reverse
218710 Spring
318711 Stop Pin
418659 O-Ring
518696 Rivet Screw (2)
618694 Screw w/ Washer (8)
718759 End Cap
818758 End Gasket
918712 C-Ring
10 18760 Ball Bearing (2)
11 18717 Guide Pin
12 18761 Rear Plate
13 18763 Rotor Blade (6/pkg.)
14 18762 Rotor
15 18764 Cylinder
16 18767 Front Plate
17 18766 O-Ring
18 18765 Oil Seal
19 18751 Motor Housing
20 18665 Valve Stem
21 18666 Throttle Spring
22 18757 Exhaust Deflector
23 18668 Hose Adapter
24 18756 Rubber Support
25 18755 Power Silencer
26 18782 Rubber Handle
27 18652 Oil Plug
28 18768 Hammer Cage
29 18769 Cam Ball Pilot
30 18770 Cam Ball
31 18771 Hammer Pin (2)
32 18772 Hammer Cam
33 18773 Cam Release Spring
34 18774 Std. Anvil 1/2" sq.
35 18775 Anvil Spacer
36 18776 O-Ring
37 18777 Retaining Ring
38 18779 Anvil Bushing
39 18781 O-Ring
40 18778 Steel Housing
41 18780 Oil Seal
42 18653 E-Ring
43 18753 O-Ring (2)
44 18754 Throttle Bushing
45 18703 Stop Cover
46 18658 Tapping Screw (2)
47 18752 Throttle Trigger Pin
See reverse side for Important Operating, Maintenance and Safety Instructions.
KEY
A
T
O1
O2
A2
O
Adhesive: A2= Loctite #271
Torque: N•m x 8.85 = In. - lbs.
Oil: O1= Air Lube
O2= SAE 20 Grade Oil
23 N•m T
17 N•m T
17 N•m
T
19
4
2
1
3
5
29 31 33 34 35 36 38 40 6
413937
47
46
32
4442
4343
27*
25
24
20
23
22
21
26
45
30
910
28
6 7 8 11 12 13 14 15 16 17 18 10
*Fill Amount – 1.5 FL. OZ. or (40 cc).
®

Autobrade Red Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade®Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety
procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid
damaging valve body housing.
3. Connect power source to tool. Be careful not to depress throttle lever in the process.
4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
Maintenance Instructions:
1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to
correct the cause before use.
2. Some silencers on air tools may clog with use. Clean and replace as required.
3. All Dynabrade rotary vane style air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if
the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).
Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.
4. It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to
unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Line Filter-Regulator-Lubricator — Provides accurate air
pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSIG
has 3/8" NPT female ports.
5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.
6. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,
chlorinated hydrocarbons or nitro carbons.
DYNABRADE®
DYNABRADE Automotive Aftermarket 8989 Sheridan Drive •Clarence, NY 14031-1490 •Phone: [phone] •Fax: [phone]
©DYNABRADE, INC., 2004 PRINTED IN USA APD00.04_Rev.1_01/04
Air Tools For The Body Shop
Visit Our Web Site: www.dynabrade.com
•Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.
•Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•Inspect abrasives/accessories for damage or defects prior to installation on tools.
•Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
•Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Autobrade Red Tool Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within 6 months from the date
of purchase, “Autobrade Red” tools are warranted against defects in workmanship and materials under normal use and service.
We shall, at our option, repair or replace at our factory, any “Autobrade Red” tool which shall, within 6 months after delivery to the original
purchaser, indicate upon our examination to have been defective.
®
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Our obligation is contingent upon proper use of “Autobrade Red” tools in accordance with factory recommendations, instructions and practices.
The warranty shall not apply in these cases:
1. Normally wearable parts such as bearings, rotor blades, etc. 5. Tools requiring normal tune-up or cleaning.
2. Consumables such as sanding pads, etc. 6. Tools being used after they are badly worn such as using ratchet with worn yoke.
3. Misuse, neglect in maintaining tool or tool modification. 7. Ratchets, anvils damaged by excessive hand torquing.
4. Lack of lubrication or evidence of rust, dirt or corrosion. 8. Use in production-type applications.
Products to be considered for warranty must be sent back to our factory, transportation prepaid by the user. Please send tool back to attention of
“Repair Department” with note fully explaining the nature of the problem along with a copy of original invoice indicating model and serial number.
Return product to:
Dynabrade, Inc.
Attn: Repair Department
8989 Sheridan Dr.
Clarence, NY 14031