E-BOX 487A11011 User manual

1
FRONT PAGE
Installation manual
© COPYRIGHT –document number: 902942-01 –note: product specifications may change without prior notice.
e·Box®II Mobile Stand
item number: 487A11
EN
NL
DE
FR
IT
ES
DA
SV
NO
FI
PL
RU
AR

2
e·Box®II Mobile Stand
document number: 902942-01
Tools
Set
Page 1:
Page 2:
Page 3:
Page 4
Last page:
Note
When
minor, these
Content of
(1x)
(1x)
(1x)
EN
General Warnings Electrical ratings
IN: 100 - 240 VAC, 50-60 Hz, max. 450 W
OUT: 12 - 40 VDC, max. 8 A

3
e·Box®II Mobile Stand
document number: 902942-01
(4x)
(4x)
(4x)
(4x)
(4x)
(4x)
(4x)
(4x)
Mounting materials [K] Part nr. 539982
Mounting materials [L] Part nr. 539993 [1:1]
[1:1]
(4x) A
(2x) C
(4x) B[1:1]
EN

4
e·Box®II Mobile Stand
document number: 902942-01
Content of the box
#481A70
VESA bracket*
** the type of this part depends on the e·Box®model
* this is an optional part
D
E
F
(2x)
I
(2x)
H
J**
K
L
G
EN #902949
Warnings booklet
#902942
Installation manual

5
e·Box®II Mobile Stand
document number: 902942-01
A: 4 x M10x30 [1:1]
Tighten with appr. torque
of 29.5 ft·lb [40 N·m]
Be careful with
removing the
plastic foil
F
G
A
1Place the motor frame base [E] on a horizontal surface. Use protection material between the surface and
product to prevent scratches, for example a sheet of foam.
2Mount the wheelbase (1 x [F] and 1 x [G]).
EN
Protect wiring
and connectors
E

6
e·Box®II Mobile Stand
document number: 902942-01
3Mount the wheels (2 x [H] and 2 x [I]). Press the pin with rolling motion into the leg bushing by hand.
4Put the product in the upright position.
2 x H 2 x I
Lock both wheels
I
I
H
H
L
EN

7
e·Box®II Mobile Stand
document number: 902942-01
5Slide the VESA box [D] over the motor frame from the top.
6Secure the VESA box with 4 screws (2 x front / 2 x back).
D
B: 4 x M6x16 [1:1]
Tighten with appr. torque
of 5.2 ft·lb [7 N·m]
B
B
EN

8
e·Box®II Mobile Stand
document number: 902942-01
7Connect the motor cables to the control box.
7c) Make sure the cables are fully plugged into the slots.
CLICK
a
7a) One motor cable into slot 1
L
1b
7b) One motor cable into slot 2
L
2
EN

9
e·Box®II Mobile Stand
document number: 902942-01
8Use the holes in the bottom of the VESA box to guide the cable for the control panel [J]* to the front side. Guide
the cables inside the VESA box. Feed the power cable down through the same holes. Use cable ties for cable
management. Cut the excessive cable ties length.
* The type of control panel depends on the e·Box®model
OR
C
OR
A2
J
8b) Make sure the cable is
fully plugged into the slot.
CLICK
8a) Control panel into slot A2
EN

10
e·Box®II Mobile Stand
document number: 902942-01
M: 4 x M8x12 [1:1]
Use the screws from 481A70.
9Mount the VESA bracket 481A70. (optional)
Please follow Installation
Manual of 481A70.
Be careful with
removing the
plastic foil
M
M
M
M
EN