Eagle P111CB User manual
Page 1
P111CB
Horn Loudspeaker
Page 2
IMPORTANT
Installer and Users please note:
These instructions should be read carefully and left with the user of the
product for future reference.
BEFORE USE
You must inspect the product for any signs of damage. If the product is
damaged, DO NOT use it, and contact your supplier immediately.
INSTALLATION
Remove the mounting bracket from the loudspeaker, and, using it as a
template, mark the positions of the three fixing holes. Drill three holes, and fit a
wallplug in each hole. Attach the mounting bracket to the wall using
woodscrews and washers. Re-attach the loudspeaker to the bracket.
Connect the loudspeaker to a 100 Volt line amplifier.
Install a junction box adjacent to the loudspeaker bracket. If installing the
loudspeaker outdoors, the junction box must have an appropriate IP rating.
The connections to a 100 V loudspeaker are considered “live” so must be
insulated to the same standard as mains terminals.
Choose the appropriate connection (either 15 W or 7.5 W) according to the
volume required from each particular loudspeaker. Use a higher power in noisy
workshops, or a lower power in quieter offices.
The amplifier is connected to the loudspeakers using a 2-core cable.
For a maximum power of 15 W, connect the white and black wires to the
amplifier output (white to positive). Make no connection to the green wire.
For a maximum power of 7.5 W, connect the green and black wires to the
amplifier output (green to positive). Make no connection to the white wire.
Connect only two wires. The third wire must be insulated so that it cannot be
touched, or touch either of the other two wires as dangerous voltages will be
present on it. The easiest way to do this is to use a three-pole terminal block.
Any number of loudspeakers may be connected to the amplifier, provided that
the maximum rated power of the amplifier is not exceeded. For each
loudspeaker connected, determine the maximum power (by looking at which
wires are connected), and add up all these figures. The total must not exceed
the rated power of the amplifier.
Page 3
OPERATION
The P111CB is a horn loudspeaker, designed for maximum efficiency in the
vocal range. It therefore has a limited frequency response of 250 Hz to 8 kHz,
which does not include bass frequencies. The loudspeaker may be damaged if
driven with excessive amounts of bass frequencies. If a bass control is available
on the amplifier then it should be turned fully anticlockwise to reduce the
amount of bass.
On specialised 100 Volt line amplifiers there may be a “low-cut” or “high-pass”
filter switch which eliminates low bass frequencies from the output. If this
switch is available, then it should be switched ON. If there is a choice of
frequencies on the filter, use 300 Hz.
FAULT FINDING
Output is very quiet on a low impedance amplifier:
The P111CB is not for use on a low impedance amplifier –use a 100 Volt line
amplifier.
Excessive distortion on music signals:
The signal contains too much bass. The P111CB is not designed to reproduce
bass frequencies.
Excessive distortion on voice announcements:
The microphone is being held too close, which increases the amount of bass in
the signal. Hold the microphone further away, or reduce the bass control on
the amplifier.
Feedback (howlround):
The loudspeaker has been mounted too close to the microphone. Either move
the loudspeaker further from the microphone, or rotate it to point away from
the microphone.
TECHNICAL SPECIFICATION
Dimensions: 221×165×235 mm
Weight: 1.6 kg
Frequency response: 250 Hz —8 kHz
Maximum power: 15 W
Sensitivity: 103 dB @1 W @ 1m
Connections: 0.5 m of 3-core cable
IP rating: IPX6
Page 4
DISPOSAL AND RECYCLING
You must not dispose of this appliance with domestic household waste.
Most local authorities have specific collection system for appliances and
disposal is free of charge to the end-user.
When replacing an existing appliance with a similar new appliance your retailer
may take the old appliance for disposal.
SERVICE WARRANTY
Electrovision guarantees the product free from defects in materials and
workmanship for a period of twelve months.
Should this appliance be operated under conditions other than those
recommended, at voltages other than the voltage indicated on the appliance,
or any attempts made to service or modify the appliance, then the warranty
will be rendered void.
The product you buy may sometimes differ slightly from illustrations. This
warranty is in addition to, and does not affect, your statutory rights.
Our guarantee is administered by our retailers.
If your product arrives damaged, you must contact the retailer from whom you
bought it. The retailer's contact details will be on the invoice that arrived with
the product, or on the e-mail you received when you placed the order. Do not
contact Electrovision, only your retailer can arrange a replacement.
If the product needs to be repaired or replaced, you must contact the retailer
from whom you bought it.
The retailer's contact details will be on the invoice that arrived with the
product, or on the e-mail you received when you placed the order.
If you have just received your product and require technical help in using it,
please call our Help Desk on (0845) 459 4816
If you have any other technical queries about the product, please call our Help
Desk on (0845) 459 4816.
Electrovision Ltd.,
Lancots Lane, Sutton,
St. Helens, Merseyside.
WA9 3EX
website: www.electrovision.co.uk
Table of contents
Other Eagle Speakers manuals
