EarthWise 60318 User manual

60318
18
DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY, PARTS, SEVICE QUESTIONS?
CALL 1-800-377-5888 (USA), 1-800-561-0004 (CNA) BETWEEN 7:30 AM - 4:30 PM EST FOR ASSISTANCE.
2012-3-23
8458-5108001-021
CorelDRAW X4
32
，
2，20，41，62
80g


8458-5108001-021

WARNING: The batteries in this product may contain one or more of the following chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm: lead, nickel, cadmium, lithium, cobalt. Wash hands after handling.
WARNING: Some dust and debris created by the use of this tool could contain chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are:
* chemicals in fertilizers
* compounds in insecticides, herbicides and pesticides
* arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure,
work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out
microscopic particles.
WARNING: The electrical cords on this product may contain chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. Wash hands after handling.
mulch plug, side discharge door, rear guard, or
other safety protective devices in place and working.

Stop the lawn mower, release the drive control bar and the
switch control bail wire.

SWITCH
KEY
MOTOR/BLADE
CONTROL
ASSEMBLY
3,250
18
...... 7 in. front, 8 in. rear
Drive Speed ....................................................... 2-2.2 mph
SWITCH CONTROL
BAIL WIRE DRIVE CONTROL BAR
43.6 kg (96 lb)

allows
the blade to cut and recut the grass for finer clippings.
1-800-377-5888 (USA), 1-800-561-0004 (CNA) for
assistance.
DRIVE CONTROL BAR
Used to engage power-propelled forward motion of lawn mower.

HANDLE KNOBS
UPPER
HANDLE
LOWER
HANDLE

hooks of the height adjustment brackets.
REAR
DISCHARGE
DOOR
DOOR ROD
GRASS CATCHER
HANDLE
HOOKS
HEIGHT ADJUSTMENT
BRACKET HOOKS

CHARGING WHEN BATTERY REMOVED
FROM MOWER
32
Insert the charger connector into the receptacle on the
battery case.
BATTERY CAPACITY
INDICATOR

Push the button on switch box and hold to allow access
to the switch control bail wire.
bail wire.
bail wire toward the mower handle
and let go of the switch button Continue to hold the switch
.
control bail wire against the mower handle as you mow.
Push battery release button forward.
Lift battery handle.
Remove battery.
To Re-install Battery Assembly
Lower handle to lock in place .
Place battery assembly into the battery compartment
of the motor cover.
To start forward motion, lift drive control bar up to handle.
To stop forward motion, release drive control bar.
Fig 9.
Start button
Switch control
bail wire Drive
control
bar
DRIVE CONTROL ENGAGED
DRIVE CONTROL DISENGAGED

bail wire immediately.
See Figure 10.
Fig 10.
Fig 11.

If environment is dusty,also wear a dust mask.
battery is removed from the battery compartment and the
switch key is removed.
REPLACING THE CUTTING BLADE
See Figures 12 - 13.
Stop the motor and remove the switch key. Allow blade
to come to a complete stop.Remove battery from the
battery compartment.
NOTE: Only use identical replacement blades.
Fig.12
To keep your drive system working properly, the gear case
and area around the drive should be kept clean and free of
trash build-up.
The gear case is filled with lubricant to the proper level at
the factory. The only time the lubricant needs attention is if
service has been performed on the gear case.
GEAR CASE
BLADE
BLOCK OF WOOD
WRENCH

FAN ASSEMBLY
BLADE INSULATOR
SPACER BLADE NUT
SHAFT
BLADE
Fig.13
Fig.14
Fig.15

self-locking nut from the wheel axle,then
remove the wheel.
wheel and install new self-locking
nut securely.
Remove battery from the battery compartment.
HANDLE KNOBS
UPPER
HANDLE
LOWER
HANDLE
SELF-LOCKING NUT
HUBCAP
WHEEL
WHEEL AXLE
Fig.16
Fig.17

Mower loss of drive or slowing of
drive speed
Stop the motor, Remove battery and
inspect for damage. Have repaired by
an authorized service center before
restarting.
Check/ replace drive belt.
Check/reinstall drive belt.
Replace drive cable.
1-800-377-5888 (USA), 1-800-561-0004 (CNA)
1-800-377-5888 (USA)
1-800-561-0004 (CNA)

MODEL 60318

GN