Easee Base User manual

Installation guide
Easee Base

IMPORTANT
Read carefully before use. Keep for future reference.
You can find other languages available on our website:
easee.support

Introduction
Technical specifications
Safety instructions
Common parts
Adapter plate
1-Way
2-Way
3-Way / 4-Way
Power Rail
Before connecting
Ground connection plate
Terminals
Wiring
Side panel
Practical details
4
5
6
8
9
10
14
18
26
27
28
31
33
36
37
Table of
contents

4
Introduction
Easee Base
Conventions This symbol indicates that the respective instructions must
only be carried out by an authorised electrician.
This symbol indicates an immediate danger to life and health
of persons due to the effects of electrical energy.
Non-observance of these instructions will result in serious
damage to health – up to and including life-threatening
injuries.
The Easee Base is a modular charging post for mounting up
to four Easee Charging Robots.
With Easee Base, it is possible to choose between four
different configurations. One-way setup where only one
charger is mounted, 2-way setup with two chargers, 3-way
setup with three chargers and finally 4-way setup where
there is a charger on all sides of the post.
With four configurations in one design, they share many
common parts. Only a few parts are specific to each type
of layout.

5
Technical specifications
Dimension (mm): H: 1500 x W: 156 x D: 80
Weight: 6.1–7.7 kg
Material: Aluminium
Finish: Powder coating
Colour: Black
IP degree: IP44
Adapter plate for c/c 160 mm2foundation
45 degree rotation intervals (using the adapter plate)
Screws and nuts included
Connection via Power Rail
Possibility of serial connection of posts
In and out of the post: Max 25 mm2
Up to the Charging Robots : 6 mm2
General
Features
Electrical connection
Cable size

6
—
—
—
—
—
—
—
—
—
—
This product shall only be installed, repaired or serviced
by an authorised electrician. All applicable local, regional
and national regulations for electrical installations must be
respected.
Danger to life due to high electrical voltage. Never make any
changes to components or connecting cables.
The installation must not be carried out in the vicinity of
flammable, explosive media, flood areas (underground car
park) or areas where there is a danger of flowing water.
The product must be installed on a permanent location.
The terminals in the Backplate are energised when the
power circuit is closed and must never be in direct contact or
in contact with anything other than the plug-in electronics
(Chargeberry).
Depending on the type of installation, official authorisations
may be required prior to installation.
Danger to life due to high electrical voltage. Never make any
changes to components or connecting cables.
Always have the prescribed maintenance, installation and
any repair work carried out by an authorised electrician.
Never extinguish the product with water. Never clean it with
running water.
Do not immerse the product in water or other liquids.
Safety instructions for
the installation
Safety
instructions
Read the entire manual carefully before installing and
operating the product. Observe the following instructions:
Safety instructions for
operation

7
It is advisable to have an extra protection around the post
when mounted in an open parking space.
This product is not intended for use by persons with reduced
physical, mental or sensory capabilities (including children)
or persons without knowledge of the product.
Make sure that children do not play with the product.
Do not use extension cords or unapproved adapters in
combination with the product.
Even if the Charging Robot is designed to withstand normal
weather conditions, we recommend protecting it from
direct sunlight or exposure to extreme weather conditions.
Do not use the product near strong electromagnetic fields or
in the direct vicinity of radio telephones.
—
—
—
—
—
—

8
Screws, washers and nut
x4 x4x1
Column Side panel Adapter platePower Rail
Ground connection plate
Common parts

9
Attach the foundation of the column to the adapter plate
with 4 socket head screws. Recommended torque is
30-40 Nm.
INFO! It can be mounted in 45° increments to get the correct
direction.
Column at a 45° angle
A
A
A
A
A
Common parts
Adapter plate

10
1-Way

11
1-way blind cover
1-Way
Parts
Mounting plate
x6 x4
Screws

12
Attach mounting plate and blind cover to the column with
3 flat head screws each (6 screws total).
NOTICE! Make sure the top end of the column is sealed with
a plastic cap.
A
A
AA
A
1-Way
Plate and
cover
1
A A

13
Thread the cable through the hole in the column and
the Easee charger backplate before attaching it with
4 rounded head screws.
B
B
B
B
B
1-Way
Backplate2

14
2-Way

15
Mounting plates
x6 x8
2-Way
Parts
Screws

16
Attach the mounting plates to the column with 3 flat head
screws each (6 screws total).
NOTICE! Make sure the top end of the column is sealed with
a plastic cap.
2-Way
Plates1
A A
AA
A A
A

17
B
B
B
B
B BB B
Thread the cables through each hole in the column and the
Easee chargers backplates before attaching them with
4 rounded head screws (8 screws total).
2-Way
Backplates2
B

18
3-Way / 4-Way

19
3-Way / 4-Way
Parts
x6 x20
Bottom frame
Top plate Top frame
3-way blind cover
Screws

20
A
Slide the bottom frame over the column and fasten it to the
lower threaded hole with 1 flat head screw on each side
(2 screws total).
3-Way / 4-Way
Bottom frame1
A