EAST COAST Kensington Sleigh User manual

IMPORTANT! RETAIN FOR FUTURE
REFERENCE. READ CAREFULLY
Kensington Sleigh Cot Bed
& Drawer
Instructions

Page 1
r e
the retailer.

3a Parts list (cot bed)
Please retain all packaging until you are certain no parts are missing.
In the case of assembly difficulties, missing parts or other queries, please contact
the customer care hotline for this product on 01692 408802.
After assembly, please dispose of all packaging carefully.
A large flat bladed screwdriver and a medium cross-point screwdriver are required
in addition to the tools supplied.
The help of an assistant will make assembly easier.
Page 2
Ends x 2
Base
Cot side x 2
Barrel nut x 4
Hexagon key
Bolt x 16
Cam pin x 1
Castor x 4
Cam nut x 1
Spanner (for castors)
Dowel x 2
Handle and screw x 2
Washer x 4 (for castors)
3b Parts list (drawer)
Drawer back
Drawer left side
Drawer right side
Drawer divider
Drawer front
Drawer bases
Short wood screw (35mm) x 10

12
Page 3
4
CAUTION: The base
must be assembled
the right way up

Page 4
5 Cot assembly
Attach both sides to the end using two bolts for each side. Ensure that the plastic
teething rail is at the top.
Attach the remaining end to the base and sides following the steps explained on
page 4.
After assembly, fully tighten all fixings before use.
6 Daybed and bed assembly
When assembling in daybed mode:
1) Attach the base in its lowest position, as for the cot.
When assembly has been completed, fully tighten all the bolts.
When assembling in bed mode:
1) Attach the base in its lowest position, as for the cot. Do not fit the sides
When assembly has been completed, fully tighten all the bolts.
2) Attach a cot side as for the cot.
Daybed mode Bed mode

Page 5
7 Drawer assembly
Before assembling the drawer, note the
joint between the drawer front and the
drawer divider uses a camlock pin A,
screwed into the drawer front and secured
by a camlock nut B inserted into the large
hole in the underside of the drawer divider.
The nut is secured by aligning the arrow on
it’s surface with the pin, inserting into the
hole, and rotating approximately half a
turn with the screwdriver.
1. Screw the camlock pin into the centre hole on the inside face of the drawer
front.
2. Push two dowels into the outer holes in the end of the drawer divider.
Drawer divider
2
A
B
3. Push the drawer divider onto the camlock pin in the drawer front.
4. Insert the camlock nut into the large hole on the underside of the drawer divider
and tighten.
Drawer front
Drawer divider
4
3
Drawer front
1

5. Ensuring that the screw holes and slots in the drawer sides and the brackets on
the drawer front line up, attach the drawer sides to the drawer front using four
short wood screws (2 in each drawer side).
Page 6
8 Drawer assembly (continued)
5
5
Drawer side
Drawer side
6. Slide the drawer bases into the slots in the drawer sides and drawer front, making
sure that the cut-outs on the drawer bases are at the outer edge of the drawer.
Drawer base
Drawer base
6
cut-outs
7. Fit the drawer back; ensuring that the drawer base parts fit into the slot in the
drawer back and secure using six short wood screws.
Drawer back
7

Page 7
9 Drawer assembly (continued)
8. Attach the castors to the underside of the drawer, fitting a washer to each one.
Tighten using the spanner supplied.
8
9. Fit the drawer handles to the drawer front with the handle screws.
9
Regularly check the tightness of screws, bolts and camlock nut and tighten as
necessary.
Check for damage which could render your cot bed unsafe or cause splinters.
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.
An occasional light application of a wax polish will help maintain a good
appearance.
10 Care of your product
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk