Eastwood CONCOURS 55001 User manual

CONCOURS®PAINT GUN STAND
INSTRUCTIONS
Item #55001
Paint Gun and Filter sold separately

2Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
The EASTWOOD CONCOURS PAINT GUN STAND is a unique modular design that can be easily
reconfigured to accept just about any size or shape paint gun or gun cup. A convenient upper hoop is
designed to support paint strainers while filling the Gun Cup. Constructed of solvent and paint resis-
tant Polybutylene Terephthalate (PBT), it is designed for years of service.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personal injury.
SAFETY INFORMATION
The following explanations are displayed in this manual, on the labeling, and on all other information
provided with this product:
READ INSTRUCTIONS
• Thoroughly read and understand these product instructions before using this
equipment. Failure to follow all warnings can result in tool damage or serious
physical injury.
• Keep these product instructions for future reference.
SHOCK HAZARD!
• Check for possible interference with electrical lines, other utilities or other
unseen obstructions before drilling or driving screws into a surface for
mounting.
INJURY HAZARD!
• Do not mount in a location where the Paint Gun Stand may become an
obstruction where head or bodily contact could cause injury.
INJURY HAZARD!
• This unit must be solidly placed or securely mounted to prevent spilling
which could cause personal injury and property damage.

To order parts and supplies: 800.343.9353 >> eastwood.com 3
ASSEMBLY (FIG 1)
• Slide the L Shape Bracket [B] into the
recess of the Base [A] so that all 4 holes
are aligned in each (FIG 2).
• Push the end of the Paint Gun Support [G]
into the recess of the Base [B] (FIG 3).
• Slip the Cup Holder Bracket [B1] down
over the upright of [B] (FIG 3).
• Slide the Extension Rod [C] over the pin
of [B] (FIG 4) (If needed).
• Place the recess of the “O” Shape Frame
[D] over the pin of [C] (FIG 5) (if needed).
• Insert the post of either the Large Cup
Holder [E] or Small Cup Holder [F]
into the open recess of the Cup Holder
Bracket [B1] (FIG 6).
FIG. 1FIG. 1
FIG. 2FIG. 2 FIG. 3FIG. 3
FIG. 5FIG. 5 FIG. 6FIG. 6FIG. 4FIG. 4
AD
B
G C F E
B1
A
B
B1
B
C
C
D
F
E
B
G

© Copyright 2021 Eastwood Automotive Group LLC 3/21 Instruction item #55001Q Rev 1
If you have any questions about the use of this product, please contact
The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: [e-mail]
PDF version of this manual is available at eastwood.com
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA
800.343.9353 eastwood.com
INSTALLATION
• For best performance, the Paint Gun Stand should be
mounted in a level position on a wall, cabinet, shelf,
workbench etc, capable of holding 10lbs. [4.5kg.] plus
pulling stresses from usage. The use of the included
screws for attachment to a structural member is highly
recommended.
• If mounting to a horizontal surface, it should be placed
near the edge to allow clearance for an attached air
supply hose.
• The Eastwood Concours Paint Gun Stand can be mounted
one of two ways: Four holes of the Base [A] using the
included 4 Long Screws to a horizontal surface or with
the back plate of the “L” Bracket [B] to a wall or other
vertical surface using the 2 Short Screws.
NOTE: If mounting to a studded wall with drywall or other
thicker covering it is recommended to use two of the
longer screws to mount into the stud.
USE
• Select the needed Cup Holder [E] or [F] based on the Gun
and Cup size.
• Set the Paint Gun into the Stand with the air cap oriented
toward the back of the Stand and the neck of the Gun Cup
cradled in the Cup Holder [E] or [F] (FIG 7).
• If a paint strainer is to be used, set it carefully into the
large, “O” Shape Frame [D] (FIG 8).
• Any unused attachments [C], [E] or [F] can be stored by
pushing the ends into various open receptacle areas of
the assembly.
FIG. 7FIG. 7
FIG. 8FIG. 8