FujiFilm SONOSITE X-PORTE User manual

1
Stand: Mobile
Printer Installation Instructions
Mobile printer installed on
the SonoSite X-Porte stand

2
Unpacking the box
Sony user documentation
Printer bracket with attached
Phillips-head screw (4)
3 mm Allen wrench (1)
#1 Phillips screwdriver (1)
Printer bracket box
Printer (1)
printer and dock cables (1)
Printer box
Printer paper (1)
Sony USB cable
(do not use)

3
Assembling the printer
Installing the printer on the stand
Slide the bracket onto the printer,
aligning the four holes.
STEP 1STEP 2
Remove the screws that
come with the printer.
STEP 3STEP 4
are attached to the bracket into the printer.
Plug the printer USB and power cables that
Screw in the four Phillips head screws.
STEP 5STEP 6
Turn off the system, and unplug it from Loosen the basket with the Allen wrench,
and lower all the way down.
the wall. Remove all USB accessories.

4
STEP 7STEP 8
Snap the printer into place
below the stand head.
Disconnect the triple transducer connector
(TTC) from the engine by pulling the
latch up and rotating it clockwise.
STEP 9STEP 10
Remove the engine by lifting
the back end out first.
To loosen the engine from the stand, raise
the control panel then release the two
latches on either side of the stand head.
STEP 12
STEP 11
Push the power and USB cables attached to the
printer bracket into the back of the stand head.
Remove the strain relief that
holds the dock cables in place.

5
STEP 14
STEP 13
Reinstall the strain relief.
Plug the cables into the dock.
STEP 16
STEP 15
Raise and tighten the basket.
Reinstall the engine by inserting the front
back end until the latches click into place.
end first. Push down on both sides of the
Reconnect the TTC to the engine.
Press the Power button on the printer,
then adjust the printer settings under
STEP 17
the system settings.
STEP 18
Plug the system AC power cord into
the wall, and turn the system back on.
Reinstall your USB devices.

6
Uninstalling the printer
STEP 1 STEP 2
Loosen and lower the basket.
Turn off the system, and unplug it from
the wall. Remove all USB accessories.
STEP 3STEP 4
Disconnect the TTC from the
engine by pulling the latch up
and rotating it clockwise.
To loosen the engine from the stand, raise
the control panel then release the two
latches on either side of the stand head.
STEP 5STEP 6
Remove the strain relief.
Remove the engine by lifting
the back end out first.

7
STEP 7STEP 8
Press the top part of the printer bracket
down, and slide the printer out.
Disconnect the printer cables. To
disengage the power cord, first
slide the jacket back from the end.
STEP 9STEP 10
Reinstall the strain relief and engine. Reconnect the TTC to the engine.
Raise and tighten the basket.
STEP 11
Reconnect the TTC to the engine, and plug
the system AC power cord into the wall.

8
X-Porte, SonoSite, and the SonoSite logo are trademarks or registered trademarks of FUJIFILM SonoSite, Inc. in
various jurisdictions.
All other trademarks are the property of their respective owners.
Patents: US 8,398,408; US 7,591,786; US D625014; and US D625015.
Published January 2017
Copyright ©2016 FUJIFILM SonoSite, Inc. All rights reserved.
P22657-01
*P22657-01*
Caution Federal (United States) law restricts this device to sale by or on the order of a
physician.
Manufacturer
FUJIFILM SonoSite, Inc.
21919 30th Drive SE
Bothell, WA 98021 USA
T: 1-888-482-9449 or 1-
425-951-1200
F: 1-425-951-1201
EC Authorized Representative
Emergo Europe
Molenstraat 15
2513 BH, The Hague
The Netherlands
Australia Sponsor
FUJIFILM SonoSite
Australasia Pty Ltd
114 Old Pittwater Road
BROOKVALE, NSW, 2100
Australia