Easydoor VM 7T BM User manual

USER MANUAL
VIDEO MONITOR VM 7T BM

CONTENTS
1.PartsandFunctions----------------------1
2.MonitorMounting------------------------1
3. Operation Instructions- - - - - - - - - - - - - - - - - - - - - 2
3.1 Answering a Door Call - - - - - - - - - - - - - - - - - - 2
3.2 DoorRelease------------------------2
3.3 Entrance Monitoring - - - - - - - - - - - - - - - - - - - 2
3.4 Intercom Function - - - - - - - - - - - - - - - - - - - - - 2
4. Basic Setup Instructions - - - - - - - - - - - - - - - - - - - 3
4.1 Ring Tone Setting - - - - - - - - - - - - - - - - - - - - - 3
4.2 Ring Volume Setting- - - - - - - - - - - - - - - - - - - - 4
4.3 Monitor Time Setting - - - - - - - - - - - - - - - - - - - 5
4.4 Unlock Parameter Setting- - - - - - - - - - - - - - - - 5
4.5ScreenSetting------------------------6
4.6 Restore to Default - - - - - - - - - - - - - - - - - - - - - 6
5. Built-in Memory and SD Card - - - - - - - - - - - - - - - 7
5.1 Picture Recording - - - - - - - - - - - - - - - - - - - - - 8
5.2 Record times Setting- - - - - - - - - - - - - - - - - - - 8
5.3 Picture Playback- - - - - - - - - - - - - - - - - - - - - - 8
5.4 PhotoFrame ------------------------9
5.4.1 Playing--------------------------9
5.4.2 Playing time setting- - - - - - - - - - - - - - - - - 9
6.Specication ----------------------------9

1. Parts and Functions
2. Monitor Mounting
145~160 cm
● Use the screws to x the Mounting Bracket on the wall.(accessories include a Bracket,
two 4X25 screws (use to fasten the Mounting Bracket), 2 wire cables (use to connect
with Monitor)).
● Connect the system correctly. then hang the Monitor on the Mounting Bracket rmly.
Home Screen
UNLOCK Button
MONITOR Button
TALK Button
CALL Button
MENU Button
Microphone
Speaker
Connection Port
Ventilation Vent
Mounting Hook
1 2 3 4 5 6
ON
DIPS
L1
BT1 BT2 EH GND VD
L2
Manual
Monitor
Monitor
Memory
Playback
Album User Setup
09/30/2010 Thu.16:41
Close
Intercom Multimedia
-1-

*Intercom Call by namelist:User in one apartment can call other apartments in the
system. Press CALL button on monitor in standby mode or touch Intercom item on
home screen page , then touch Intercom by Namelist icon (the namelist will be
created automatically by the system). Select a name on the screen then touch Dial
Number icon to call.Press icon to enter last/next name list page.
3. Operation Instructions
3.1 Answering a Door Call
3.2 Door Release
3.3 Entrance Monitoring
3.4 Intercom Function
● Press the CALL button on door station.
● The monitor rings,and the visitor's image will be seen on screen.
● Press TALK Button or touch icon, you can talk
with the visitor for 90 seconds. During talking state,
press the TALK Button again or press icon to
end the conversation. If the system connects two or
more Monitors, pick up any Monitor , the others will
be automatically shut off.
● Press MONITOR button on monitor in standby
mode,or touch Monitor icon on home
screen.the screen will display the view of the
Outdoor Station. During monitoring, touch
Manual Monitor icon to get into the camera
switching mode, (or directly touch Manual
Monitor icon on home screen), if multi Door
Stations are installed, you can press the camera
1/2/3/4 to monitor the Door Station or CCTV
camera you want.press Home icon to exit
and enter home screen page.
● During the conversation, press UNLOCK Button or touch icon to unlock the door.
(if two locks are connected to door camera,touch unlock 2nd icon to release the
second lock )
Note:the screen turns off after 30 seconds if nobody answers.
Home
Unlock
Talk
Standard
Screen
Capture
1:1
-2-
Camera 1 Camera 2 Camera 3 Camera 4
2 3 41
09/30/2010 Thu.16:41
Home
Monitor
Time

4. Basic Setup Instructions
*Inner Call: If multi Monitors are installed in one user, select and press the Inner Call
item, the other Monitors will ring at the same time, whichever Monitor answers the call,
conversation is started,and the other monitors will stop ringing at the same time.
*Direct Dial Guard unit: A Monitor can be assigned as Guard Unit Monitor; when the
Guard Unit Monitor answers the call, conversation with the guard person is started..
4.1 Ring Tone Setting
● Touch the screen anywhere (or press MENU button ) in standby mode,a full screen
calendar will be showed.
12 pieces ring tones can be selected.
1. Current date
2. Current day
3. Current time.
Intercom
by Namelist
Inner Call Direct Call
Guard Unit
09/30/2010 Thu.16:41
Home
Dial
Last
-Name List-
[0002] Calo,Liu
[0003] Jacko,Zhang
[0004] Jana,Qiao
[0005] Hebe,Zhang
[0006] Tony,Li Close
Next
09/30/2010
16:41
Thu.
*Note:1. Press "CALL" button or touch Dial Number icon again to redial. 2. Touch
icon to cancel the call.
-3-
[0001] Jim
Number

● Touch the screen again (or press MENU
button again) to enter home screen. then touch
User Setup icon to enter call tone setting
screen,touch Door station call tone/intercom
call tone/door bell call tone,12 pieces ring
tones will be displayed , Choose a ring tone
which you want, then touch icon to save
and exit, the ring tone will be performed. or
touch icon to unsave and exit.
4.2 Ring Volume Setting
You can set a ring volume for day time,6:00
AM~18:00 PM is the day time by default,enter
home screen page(refer to 4.1) then touch
User Setup icon to enter next page,and then
touch Ring Volume icon to enter Ring
Volume page,Use icon to decrease/
increase the volume. then touch icon to save
and exit,or touch icon to unsave and exit.
Ring Volume
Night Ring Volume
Ring Volume
6
7
Adjust - Adjust +
Exit&Save
Exit&Unsave
Door Station
Call Tone
Exit&Save
Carman
Ding Dong
Rhythm of the rain
For Elise
Sonatine
Edelweiss
Going Home
Congratulate
Do Re Me
Happy Birthday
Jingle Bell
Telephone Ring
Exit&Unsave
You can active a ring volume for night time,18:00 PM~6:00 AM is the night time by default,if you
don't want to be disturbed at night ,you can set the volume to 0.Enter home screen page(refer
to 4.1) touch User Setup icon to enter next page, then touch Night Ring Volume
icon to enter Night Ring Volume page,Use icon to decrease/increase the volume.After
setting a value you want,you should touch Ring Volume icon to active the setting, after
that the Ring Volume icon will change to Night Ring Volume icon. then touch
icon to save and exit,night ring volume will be performed. or touch icon to unsave and
exit.
Note:touch Night Ring Volume icon again,you can cancel the night ring volume setting.
-4-

Night Ring
Volume Night Ring
Volume
4
7
Adjust - Adjust +
Exit&Save
Exit&Unsave
Night Ring
Volume
Adjust - Adjust +
Exit&Save
Exit&Unsave
4
Ring
Volume
● Enter home screen page(refer to 4.1),thenTouch Manual Monitor icon to enter
next page.and then press Monitor Time icon to enter monitor time setting page.
● Input digitals by pressing the digital keypad, and press icon to change the setting
location,and press icon to save. Settings will be performed immediately, press
icon to return last page .
icon to enter next page.
and then touch the screen anywhere and hold for 2s to enter next menu.
4.3 Monitor Time Setting
4.4 Unlock Parameter Setting
Camera 1 Camera 2 Camera 3 Camera 4
2 3 41
09/30/2010 Thu.16:41
Home
Monitor
Time
Monitor time set
1
4
7 8
0
9
65
2 3
min:[01] sec:[30]
Cancel
H/W DT14-CT a1.3
S/W: V11.01008.00
Voltage: ---
Local addr: 01.00
Unlock timing: 5s
Video standard: NTSC
Cancel
Home
Installer
setup
Device
Property
Caliber
TouchScreen
-5-
●Enter home screen page(refer to 4.1),thenTouch easydor™

4.5 Screen Setting
4.6 Restore to Default
When the Monitor is in monitoring or talking
state, Press Adjust icon to enter
screen setting page.Touch any item you
want,then touch to decrease or
increase the value.Settings will be performed
immediately. Press icon to exit out the
page.
The restore to default function allows the
user to recover the settings to factory setting.
Note that the restore to default operation will
not change the time setting and the datas on
buit-in memory or SD card.
Enter home screen page(refer to 4.1),then
touch User Setup icon to enter the
setting page,press Restore to default item,
the default settings will be loaded. press
Home icon to return to home screen page.
5
Brightness
color
scene
Talk Volume
Adjust Return
Adjust - Adjust +
Door Station
Call tone
Intercom
Call tone
DoorBell
Call tone
Clock
Ring
Volume
Night Ring
Volume
Refault to
Default
09/30/2010 Thu.16:41
Home
● Touch Installer setup icon,a digital
keypad and installation setting will be
showed on screen.
● Input code number by touching the digital
keypad.According to the left instructions,
8010 and 8011 are used to set the unlock
mode(0 and 1). 8021~8029 are used to set
the unlock time (1s~9s) .use to cancel
the input,and use to save the setting.
Touch icon to return last page .
Code Number:[----]
[0010]#:Remove all remote control
[0011]#:Add remote control
[8000]#:Set as master unit 0
[8001]#:Set as slaver unit 1
[8002]#:Set as slaver unit 2
[8003]#:Set as slaver unit 3
[8004]#:Set as guard unit
[8005]#:Set as not guard unit
[8010]#:Set lock mode to 0
[8011]#:Set lock mode to 1
[8021]#:Set the lock time of 1s
[8022]#:Set the lock time of 2s
[8023]#:Set the lock time of 3s
[8024]#:Set the lock time of 4s
[8025]#:Set the lock time of 5s
[8026]#:Set the lock time of 6s
[8027]#:Set the lock time of 7s
[8028]#:Set the lock time of 8s
[8029]#:Set the lock time of 9s
1
4
78
0
9
6
5
23
Cancel
Installation settings:
-6-

5. Built-in Memory and SD Card
This Monitor has been equipped with a built-in memory (about 120 MB) together with a SD card
reader. Maximum 16 GB SD card can be supported.
● The monitor can play photos and pictures.
● Photo frame function, each photo playing will last 5 seconds, More pictures in the SD card,
longer time for triggering the function, 800 pictures is supported in inner memory. With 2G SD
card,more than 30000 pictures can be supported.
● Must use T-views album software tool to transform the JPG format photos took by digital
camera to TVS format photos that can be viewed on Monitor.
● The captured pictures will be saved in a folder named by date,note that the pictures recording
every day will be saved in different folders which automatically generated every day.
● The captured pictures in the built-in memory can be copied to the SD card, and you should
use T-views memo software tool to convert the pictures to JPG format that can be seen on
the computer. (select the pictures(press Ctrl+A to select all)->>click the right key of the mouse
->>choose transfer selected to JPG item->>save the pictures on computer)
● When the built-in memory is full,the oldest picture will be deleted to make room for new record .
● The built-in memory can be formatted by the Monitor,but SD card cannot,you should format the
SD card on computer.
● Avoid to plug in/out the SD card when the monitor is under operation.
● Playing will be interrupted by the calling from outdoor station.
SD card
-7-

5.1 Picture Recording
5.2 Record times Setting
5.3 Picture Playback
Both Auto-Recording and Manual-Recording
are available.and Auto-Recording is default. If
receive a Call , after 3s, the monitor will record
automatically. or you can touch Capture
icon to record the visitor's image manually.
Touch Memory Playback icon on home
screen,4 pictures will be displayed in the memo
for each page. you can touch or to
enter last or next picture memo,or touch
icon to delete all pictures. And you can zoom
the picture on full screen by touch icon , on
full screen mode, touch icon to preview
last/next picture.or you can touch icon to
delete the picture you are previewing.press
icon to return home screen page.
You can setup Memo Options to choose 1/4/8
pictures memo. If 4/8 was chosen, you will have
4/8 shots for each recording operation, and
every 1.5 seconds catch a picture.
Touch Multi Media icon on home screen
to enter next page, then touch Memory
Options icon,a digital keypad will be showed
on the screen,you can only set the record times
for 1/4/8 by touching the digital keypad.touching
other digitals are unvalid .and press icon
to save. Settings will be performed immediately,
press icon to return last page .
Record times: [ 1 ]
1
4
7 8
0
9
65
2 3
Cancel
Page Down
Home
Full Screen
Picture 4
2010-9-30 004 2010-9-30 003
2010-9-30 0012010-9-30 002
Picture 3
Picture 1Picture 2
Delete All
Page UP
Recording...
DS1 00:03 Talking
Home
Unlock
Talk
Standard
Screen
Capture
1:1
-8-

6.Specication
5.4.1 Playing
5.4.2 Playing time setting
Touch Album icon on home screen to play the photos(must plug in SD card).it can be
played both manually and automatically,use your ngers to slide right or left on screen to play
last/next photo.
Touch Multi Media icon on home screen
to enter next page, then touch Album
Options icon,a digital keypad will be showed on
the screen,then you can set the playing time by
touching the digital keypad to input digitals and
press icon to change the location,and press
icon to save. Settings will be performed
immediately, press icon to return last page .
5.4 Photo Frame
Power Consumption: Standby 15mA; Working status 400mA
Monitor Screen: 7 Inch color TFT-LCD
Display Resolution: 800*3(RGB)*480 pixels
Built-in Memory: 120 MB
Picture Memo: 800pcs(inner memory),>30000pcs(2G SD card)
Monitor Dimension: 138(H)×235(W)×24(D)mm
Album time set
1
4
7 8
0
9
65
2 3
min:[01] sec:[30]
Cancel
-9-
Power Supply : supplied by power separator