EasyWater RevitaLife User manual

Installation Manual & Owner’s Guide

Table of Contents
How RevitaLife Works................................................................................................................................................................. 2
Unpacking & Inspection............................................................................................................................................................. 3
Specifications.................................................................................................................................................................................. 3
Contents............................................................................................................................................................................................. 3
Installation ..................................................................................................................................................................................... 4-9
Start Up Instructions...................................................................................................................................................................10
Cartridge Replacement .............................................................................................................................................................10
Annual Maintenance Recommendations.........................................................................................................................11
Limited Warranty...........................................................................................................................................................................12
RevitaLife |Installation Manual & Owner’s Guide

2RevitaLife |Installation Manual & Owner’s Guide
Congratulations on the purchase of your new EasyWater RevitaLife Drinking Water System. As
with every EasyWater product, we are confident that you will be completely satisfied with your
purchase. EasyWater is dedicated to providing the healthiest and most
eco-friendly products to our customers.
A ) Sediment Filter: Removes dirt and sediment particles down to 5 microns in size.
B ) Carbon Block Cartridge: Removes chlorine and reduces many pesticides, herbicides, THMs,
VOCs and more.
E ) Reverse Osmosis Membrane: Effectively removes most remaining contaminants down to .0001
micron in size, including nitrates, arsenic, chromium 6 and many more.
C ) Remineralizing Filter: Raises pH and adds benecial minerals back to water. The water-driven
permeate pump boosts pressure and directs the water into the compact 3 gallon storage tank.
D ) Final “Polishing” Filter: High-quality activated carbon provides a nal ltration step on the way
to the faucet.
A B DC
E
Scan QR Code
to Watch Video
How RevitaLife Drinking Water System Works
Benets of EasyWater RevitaLife
9Powerful RO membrane effectively removes
contaminants down
to .0001 micron in size
9Signicantly reduces most of the 84,000+ toxins that
may be in your water
9Unique remineralizing process restores healthy minerals,
raises pH and improves taste
9Internal water-driven pump produces more water, and
reduces water usage up to 80%
9Makes great tasting coffee,
tea and ice cubes
9No need to buy and dispose
of plastic water bottles
9Choice of designer faucets

3RevitaLife |Installation Manual & Owner’s Guide
Specications
Contents
»Wall module with reverse osmosis membrane housing pre-installed
»RevitaLife face plate
»Four lter housings
»Storage Tank
»Parts Bag
»Tubing
- Red ¼” – supply line
- Black ¼” – permeate pump to drain
- Green 3∕8” – RO remineralizer cartridge to tank
- Blue 3∕8” – RO nal carbon lter to faucet
- Optional 3∕8” black – to drain if faucet is air gapped
»Top Mounting Faucet – packaged separately
*Water hardness above 10 gpg requires installation of EasyWater No-Salt Conditioner.
Model
RL5010
Min Incoming
Water Pressure
30 psi
Max Incoming
Water Pressure
100 psi
Hardness
(less than)
10 gpg*
Maximum
Iron
0.2 ppm
Maximum
H2S
0.2 ppm
Maximum
Manganese
0.05 ppm
Maximum
TDS
2000 ppm
Turbidity
(Cloudy Water)
1.0 ntu
Unpacking & Inspection
Be sure to inspect the entire shipment immediately upon receipt for any shipping damage or parts
loss. Also note any damage to the shipping carton. Contact the transportation company for all
damages and loss claims. EasyWater is not responsible for damages in transit.

4RevitaLife |Installation Manual & Owner’s Guide
Installation
RECOMMENDED TOOLS FOR INSTALLATION
»1¼” Hole saw bit for faucet opening OR 1¼” knock-out punch for stainless sinks
»Adjustable wrench
»Sharp knife or utility cutter
»½” – 13⁄16” open end wrenches
»Phillips screwdriver
»Needle nose pliers and adjustable pliers
»Electric variable speed drill
PRODUCT DIMENSIONS
DRILL OR PUNCH A FAUCET HOLE IN SINK OR COUNTERTOP
Using a 1¼” hole saw bit or knock-out punch, create a hole for the faucet in sink or countertop.
Different sink or countertop materials require different tools and methods for punching
or drilling a hole. Use proper tools and follow your sink or countertop manufacturer’s
instructions to prevent damage. EasyWater accepts no responsibility for damage resulting
from the installation of an RO faucet.
19”
Depth: 5”
9”
17½” 19”

5RevitaLife |Installation Manual & Owner’s Guide
Installation (Cont’d)
TOP MOUNT FAUCET INSTALLATION
Mounting hole size: Minimum 1” ; Maximum 1¼”
Max torque on toggle bolt: 5 lb. in.
1) Remove faucet base and faucet spout from bags. Ensure that 2 black O-rings and 3-prong
plastic spacer are attached to the base of faucet spout, as pictured above.
2) Attach blue tubing to the bottom of the toggle bolt on faucet base. Remove adhesive backing
from faucet base.
3) Feed the faucet tubing and toggle bolt down through the hole in sink. Ensure that the rubber
gasket is uniformly positioned between the base and sink.
4) Align faucet base with handle on right side and base sitting on top of sink. Turn the handle down
(towards you) to the “on” position to reveal the tightening screw (located where the spout will
be inserted). Using a Phillips head screwdriver, turn the screw clockwise until the toggle bolt
secures the faucet base snug on the sink top.
5) When faucet base is securely fastened to the sink, insert the faucet spout into the faucet base
until it is fully sealed. Do NOT remove O-rings or plastic spacer on faucet spout base. Turn the
handle to the “off” position.
6) Proceed to Adapt-A-Valve Installation.

6RevitaLife |Installation Manual & Owner’s Guide
ADAPT-A-VALVE INSTALLATION
1) Verify contents prior to installation.
• plastic Adapt-A-Valve
• brass adapter with washer
• brass adapter without washer
• white rubber washer
2) Locate and turn off the cold water supply line under the sink.
3) Attach the Adapt-A-Valve to the cold water supply line as illustrated below, choosing the
conguration that ts your plumbing. Do NOT use Teon tape to assemble Adapt-A-Valve.
4) The red ¼” tubing connecting the Adapt-A-Valve to the inlet of the reverse osmosis module will
be cut to length and attached later in the installation.
REVITALIFE MODULE MOUNTING
Determine the best location for the RO wall module to be mounted to allow for future cartridge
changes and system maintenance. If installing under a sink, be sure the mounting screws are at
least 19” from the bottom of the cabinet to allow for changing cartridges. Mount securely. System
is heavy when installed and full of water.
Note: Do NOT cut any system tubes at this time.
Installation (Cont’d)
Conguration for 3∕8” plumbing with
brass ttings and white washer
Hot Supply Cold Supply Conguration for ½” plumbing with-
out brass ttings and white washer

7RevitaLife |Installation Manual & Owner’s Guide
Installation (Cont’d)
DRAIN SADDLE INSTALLATION
Drain Saddle ts standard 1 ¼” – 1 ½” drain pipes
Important: When installing under a sink, the drain saddle will be installed on the vertical drain
pipe (tailpiece), above the p-trap. The drain line installation must be either above the disposal, or if
a second sink drain is available, install it above the cross bar on the second sink. Installation of the
drain saddle below where the outlet of a garbage disposal connects to the vertical drain pipe may
cause the drain line to plug.
»Verify contents prior to installation
(2) Screws with nuts
(1) Semicircle bracket with opening
(1) Semicircle bracket
(1) Foam gasket
1) Apply the adhesive-backed foam gasket to the inside of the semicircle bracket with opening,
aligning holes.
2) Drill a ¼” hole through the sink’s drain pipe at least 1 ½” above the connecting nut of the P-trap;
be sure to allow for future removal of the P-trap. Place the drain saddle around the drain pipe,
positioning the drain saddle over the drilled hole in the pipe. To ensure proper alignment, insert
a screwdriver through the opening of the drain saddle and the drilled hole in the drain pipe.
Tighten screws evenly and securely on both sides of the drain saddle.
Caution: Do not over tighten the screws. This may crack the drain saddle.
TANK VALVE INSTALLATION - PLASTIC TANK
1) Make sure the O-ring is located at the bottom of recess
for the tank connection.
2) Thread the plastic tank shut-off valve onto the tank tting.
Hand tighten only. Do not over tighten or the valve
could crack.
NOTE: Tank can stand vertically or lay horizontally.

8RevitaLife |Installation Manual & Owner’s Guide
Installation (Cont’d)
TUBING CONNECTIONS
1) Connect red ¼” supply line from
Adapt-A-Valve outlet to RO inlet.
3) Connect blue 3∕8” line from nal polishing lter
cartridge (D) to faucet.
2) Connect green 3∕8” line from T tting to tank.
4) Connect black ¼” line from permeate pump
output to ¼” x 3∕8” tting drain saddle.
IF FAUCET AIR GAP IS REQUIRED
1) The black ¼” line from permeate pump output will connect to faucet air gap inlet.
2) The black 3∕8” line from faucet outlet will connect to drain saddle.
If you opt to cut tubing prior to making connections, ensure tubing is cut at a 90° angle. Improper
cutting will increase risk of leaks.
Adapt-A-Valve
Faucet Connection
Final Polishing
Filter
R.O. Inlet
T-Fitting
Permeate Pump
Output
Drain Saddle
Tank

9RevitaLife |Installation Manual & Owner’s Guide
FILTER & FACE PLATE INSTALLATION
1) Remove the protective cap from cartridges A, B, C and D (cartridge E comes pre-installed).
2) Position the cartridge with the label facing left.
3) Push the cartridge onto the head and rotate to the right ¼ turn until it locks into position.
4) Follow steps 2 and 3 for each cartridge.
5) Turn on water supply line and check for leaks.
6) Attach face plate to the wall module.
OPTIONAL REFRIGERATOR KIT INSTALLATION
NOTE: A refrigerator kit can be ordered by contacting EasyWater.
1) Tee off from the line running from the RO unit to the faucet.
2) It is recommended to install a shutoff valve on the line running from the line in Step 1 to the
refrigerator.
3) Follow the manufacturer’s instructions to connect the line from Step 1 to the refrigerator.
Installation (Cont’d)

10RevitaLife |Installation Manual & Owner’s Guide
Start Up Instructions
Important: If system is connected to a refrigerator, shut off water flow to the refrigerator
until Step 5, “flushing”, is complete and the tank has been filled completely.
1) Turn off the valve connected to the tank.
2) Turn on the incoming cold water at the angle stop valve. Open the Adapt-A-Valve by turning
counter clockwise. Check the system for leaks and tighten any ttings as necessary.
3) Open the RevitaLife faucet and leave open until water begins to trickle out slowly, then close the
faucet.
4) The tank will take approximately 2-3 hours to ll completely. Check frequently over the next
24 hours to ensure no leaks are present. EasyWater accepts no responsibility for damage
resulting from leaks.
5) After the tank has filled, open the faucet and allow water to run until the tank empties
and water flow slows to a trickle. Carbon fines, or slightly grayish water, may be present.
Flush the tank in this manner 3 times. You only need to flush the tank during initial
installation or cartridge replacement.
The A, B, C and D cartridges should be changed annually. The reverse osmosis membrane (E)
should be changed every two years. Note: Although each cartridge head has a built-in automatic
shutoff, a small amount of water may be released when changing cartridges.
1) Shut off the water supply line.
2) Rotate the cartridge ¼ turn to the left.
3) Pull down on the cartridge.
4) Remove the protective cap from the new cartridge.
5) Position the new cartridge with the label facing left.
6) Push the cartridge onto the head and rotate to the right ¼ turn until it locks in position.
7) Repeat steps 4-6 for each cartridge.
Note: See Start Up Instructions for how to restart system after cartridge replacement.
Cartridge Replacement

11RevitaLife |Installation Manual & Owner’s Guide
Annual System Maintenance Recommendations
STORAGE TANK SANITIZATION
1) Turn off the incoming water supply at the Adapt-A-Valve.
2) Open the faucet, allow the tank to empty, then close the faucet.
3) Remove the tubing between the tank and the RO unit.
4) Drain the water from the tubing and inject one teaspoon of household bleach into the tubing.
5) Reinstall the tubing between the tank and the RO unit.
6) Turn on the water supply at the Adapt-A-Valve.
7) Allow the RO tank to ll, open faucet and fully drain the tank, then close the faucet. Repeat Step
7 a second time.
TANK AIR PRESSURE
1) Turn off the incoming water supply at the Adapt-A-Valve.
2) Open the faucet, allow tank to empty, then close faucet.
3) Check the pressure in the tank using a tire pressure gauge.
4) Once emptied, the tank pressure should be between 5-7 psi. Add air if necessary by using an
air compressor. Do not overll.
5) Turn on the water supply at the Adapt-A-Valve.
PROCEDURE FOR EXTENDED NON-USE
(if system is not used for more than two months)
1) Turn off the incoming water at the Adapt-A-Valve.
2) Open the faucet, allow tank to empty, then close the faucet.
3) Remove and discard all lters (A, B, C and D) and membrane (E).
4) To place system back in service, replace lters (A, B, C and D) and membrane (E), then follow
startup and tank sanitization procedures.

12RevitaLife |Installation Manual & Owner’s Guide
Limited Warranty
EasyWater, Inc., Fishers, IN warrants this EasyWater RevitaLife (referred to as System) as stated
herein:
From the date of installation, within the warranty period described below, we will repair or replace
any part which we nd defective because of faulty materials or workmanship. You pay only freight to
our factory and local labor charges.
- One year on complete unit excluding cartridges and membranes
Damage to any part of System because of misuse, misapplication, neglect, alteration, accident,
installation or operation contrary to printed instructions, or damage caused by an act of terrorism
or any unusual force of nature such as, but not limited to, freezing, ood, hurricane, tornado or
earthquake is not covered by this warranty. In all cases, regular parts and service charges will
apply.
We assume no warranty liability in connection with this System other than specied herein. This
warranty is in lieu of all other warranties, express or implied, including warranties of tness for a
particular purpose. We do not authorize any person or representative to assume for us any other
obligations on the sale of this lter.
Should a defect or malfunction occur, EasyWater, Inc., at [phone] or via email at
[e-mail]. We will repair or replace the part at no cost if our repair
department determines it to be defective under the terms of the warranty.
Feed water quality must meet the requirements for this system on an ongoing basis in order for
this warranty to be valid.
This warranty is valid for the original purchaser only and gives you specic legal rights. You may
have other rights which vary from state to state.
FREIJE Treatment Systems, Inc.
9715 Kincaid Drive Suite 1100 Fishers, IN 46140
[phone]
Lit No. RLISMOG021813