EC Pedals Superswitcher User manual

The super switcher is a professional programmable switching system for guitar and bass systems featuring:
- 8 eect loops - 7 mono and 1 stereo return for stereo pedals
- 7 X 3 presets for saving all presets easily
- 5 Amp control relay functions for controlling amp channels, FX and more
- high quality input buer selectable on\o for keeping the right tone when using long cables
- Tuner out for silent tuning and keeping the tuner out of the audio path
- Makes all your pedals true bypass
Players could turn on couple of pedals,
switch amp channels and turn on amp reverb all in one click!
Moreover the super switcher features a link option which will able the player to link 2 units for endless options:
1 - Put one backstage with all the pedals and amps and one of the stage front just as a controller to get clean stage operation
2 - Put one on the stage for your in front pedals and one back stage for your FX LOOP pedals
3 - Just to add more loops and controls
The super switcher will also be including a control output for
the relay functions - together with custom amp cables that
we make you could send only one cable to your amp - keeping
the stage even cleaner.
The super switcher is the next evolution for easy programming
your presets all can be done with your feet, the unit is built with
the highest quality parts as we never save on parts.

Bank - The SuperSwitcher has 3 banks which will give you 3X7 presets for a total of 21
presets.
Remember - when pressing the Edit button to be on the Bank you want to edit.
Bypass\Edit - On“Play”mode this button act as a bypass switch - no matter which preset is
on and which pedals are on when you press the Bypass button all Loops are disconnected from
the audio chain and the Superswitcher is canceled as once - making your guitar plugged from the
Input jack straight to the Output jack of the SuperSwitcher.
Tuner\Mute- On“Play”mode this button act as a tuner out switch.
when pressing it the guitar signal going from the input jack to theTuner jack by that
keeping your tuner out of the audio chain.
Pressing the Tuner button also cancel all loops and by that it mutes the guitar and pedals
making your amp clean and quiet while tuning your guitar.
When you press it again to go out of the tuner mode you will get instantly to your last preset
Loops jacks - Each loop has send jack which will go to your pedal input jack and return jack which will be connected
to your output jack of your pedal. Loops 1-7 are mono , loop 8 has stereo return jack (use withY cable) for stereo pedals.
S1-5 jacks - Those are your Relay switching jack for controlling amp channels , reverb and anything you want to switch
with a relay switch. all S jacks are truly isolated from each other and each have separate ground (GND not common).
CON Jack - This Jack represent S1-5 but HAS common grounds! you can use this jack to ask us for a custom cable for
your amplier instead of using PL cables for the relay switches. *depend if the amplier support common grounds*
Link Jack - This Jack uses RJ-45 connector to connect the SuperSwitcher to another SuperSwitcher for more features
which will be covered on the LINK CONNECTIONS section on the manual.
DC Jack - The Superswitcher uses a standard 9VDC - negative tip connection like most pedals on the market.
Audio Buer - If you have a long cable or alot of pedals we recommand engeging the buer
by keeping it UNPRESSED, you can adjust the level of the buer by the small trimmer pot inside
the SuperSwitcher making it even as a booster.
To cancel the Buer you need to press the switch ON.

Editing presets on the SuperSwitcher is very easy and can be done in a few seconds, the instructions
are very easy:
1 - With the BANK button - set the bank you want to edit it’s presets.
2 - Press the EDIT button for 2 sec’you will see the blue LED icks for a second and then it turned o - release press.
3- If you want to edit a manual switch instead of preset press the bank button once at this point (C LED will ash)
4 - Now press for 2 sec on the preset you want to edit 1-7
5 - You are now editing a specic preset on a specic bank - on this mode the BANK LED’s represent L mode for loops
or S mode for switchers. You can switch between the 2 modes with the BANK button.
6 - Set BANK button to L mode and press buttons 1-8 (8 is the EDIT button) to choose which loops you want to activate
on this specic preset that we are editing.
7 - Set BANK button to S mode and press buttons 1-5 to choose which relay switches you want to activate on this specic
preset that we are editing.
8 - When nished you can either save the preset and start editing another preset by pressing the SAVE(Tuner\Mute)
button once , or when you nished editing all the presets you want and go directly to“PLAY”mode press it for 2 sec’.
Those are the steps for editing a preset, you can do this in order to edit all 1-7 presets within all 3 banks.
Reset mode - if you want to reset the superswitcher from all presets (factory reset) - unplug the DC cable from the super
switcher, while the unit is o press both the BANK and BYPASS\EDIT buttons together and keep them pressed, while you
are still pressing them plug back the DC cable to the unit - LED’s will ash and tell you the factory reset is done.
Manual mode - if you dont want to use your presets at all at certain day you can set the superswitcher to act as a
normal pedal board with up to 8 pedals and 1 relay switch, to do so unplug the DC cable from the super
switcher, while the unit is o press both the TUNER\MUTE and BYPASS\EDIT buttons together and keep them pressed, while you
are still pressing them plug back the DC cable to the unit - LED’s will ash and tell you the you are in manual mode.
In this mode you can press 1-8 buttons to immediately turn on loops 1-8, you can turn on and o couple of loops together,
also you can use the BANK button in this mode to turn on S1 relay switch. keep in mind the buer and theTUNER options
can be used in manual mode.
Link connections - you can use 2 superswitchers and link them together for multiple modes:
1 - Put one backstage with all the pedals and amps and one of the stage front just as a controller to get clean stage operation
2 - Put one on the stage for your in front pedals and one back stage for your FX LOOP pedals
3 - Just to add more loops and controls
Before you plug both units you need to edit your presets:
1 - Edit your preset on the rst superswitcher with the loops and switches you want to for this unit
2 - Edit the same preset on the second superswitcher with the loops and switches you want to for this unit
3 - when the cable is connect and you press on“play”mode on the preset you will see it sets your preset on both units