Eco Tm-050b User manual

Outdoor Wi-Fi Smart Box

CAUTION!

For outdoor use. For installation, rain-tight or

wet location conduit hubs that comply with requirements of

UL 514B Conduit, Tubing, and Cable Fittings must be used.

Note:

Installation should be made by a licensed electrician.

Turn power OFF at the circuit breaker before installation.

READ ALL INSTRUCTIONSbefore using the ECO Smart Box.

Power Button

Press this

button to

manually

override the

ECO Smart

Box and turn

the unit ON/OFF.

TO CONNECT THE ECO SMART BOX TO A WI-FI ROUTER

• With the ECO Smart Box installed, if the blue light is blinking you can

proceed to the next step to begin the smart phone setup. If not blinking,

you must reset the ECO Smart Box as described in the FAQ section on

the reverse side of this sheet. Make sure the controlled device(s) are

switched ON. Note: the blue light will continue blinking until the setup

is finished via the smartphone app.

• Once you are finished connecting the ECO Smart Box to a Wi-Fi router,

the blue light will remain on continuously to indicate that Wi-Fi connection

has been established and the ECO Smart Box is accessible via the app.

Power Indicator

Select the Wi-Fi router that you want to

link to the ECO Smart Box. (Note: It may

take a few seconds for network communication).

Tap the

ECO icon

STEP 3: Fill in the information (Note: US

residents enter your five-digit ZIP code,

Canadian residents enter your three-digit

telephone number area code). When

finished filling in the information, click

the SAVE SETTINGS or JOIN button.

(In iOS: if you can't find the JOIN

button, click in the “Password” box).

STEP 2:

TO ADD ADDITIONAL ECO SMART BOXES TO THE APP: Repeat steps

1-3 for each additional ECO Smart Box. Remember to give each box a

different name (for example, Master Bedroom, Home Office, etc.).

Note: Each ECO Smart Box can be wired to control one or two circuits.

To control more than two circuits, add additional ECO Smart Boxes.

ECO Status Indicator

Blinking Light: Ready to

connect to Wi-Fi router.

Light continuously ON:

Connection to Wi-Fi

router is complete and

the ECO Smart Box is

ready for use via the app.

Light OFF: Check your

internet connection or

review the app FAQ.

Reset Button

IMPORTANT:

Please refer to INSTALLATION INSTRUCTION SHEET

before proceeding with Wi-Fi router connection. ECO Smart Box

must be installed before connecting to Wi-Fi router. Usage: Function is not available

on this device.

More: Learn more about this app,

including an FAQ section.

Settings: To set your Wi-Fi Smart Box,

transfer local Wi-Fi to cloud mode, or to

rename the ECO Smart Box.

Timer: To set ON/OFF programs (up to a

maximum of 12 Custom ON/OFF events).

Cloud Icon: Activates remote access

function of device through 3G, 4G, LTE,

public Wi-Fi network, or other Wi-Fi router.

Mailbox: To email consumer service or

share app feedback.

Programmable Timer: To set custom

ON-OFF events.

Countdown Timer: The controlled device

will turn off after selected time.

Astronomic Timer: The controlled device

will turn on or off at sunset or sunrise.

Vacation Random: The controlled device

will turn on or off randomly between one

of three time frames (night, day, all day).

Security Random: The controlled device

will turn on and off randomly between

chosen start and end times.

N.O. Contacts:

40A Resistive, 120~277VAC

1HP, 16A FLA, 96A LRA, 120VAC

2HP, 10A FLA, 60A LRA, 277VAC

30A Ballast, 120VAC

20A Ballast, 277VAC

15A Tungsten, 120VAC

30A Resistive, 28VDC

N.C. Contacts:

30A Resistive, 120~277VAC

1HP, 16A FLA, 96A LRA, 120VAC

2HP, 12A FLA, 72A LRA, 240VAC

2A Tungsten, 120VAC

10A Ballast, 120VAC

10A Ballast, 277VAC

20A Resistive, 28VDC

Tap Smartphone’s

Settings icon

Tap the

Wi-Fi icon

Select the

ECO Smart Box

STEP 1:

Choose a Network

Device [ECO-XXXXXXXX] Ver: XXX

Home Router

Other Router A

Other Router B

(such as lamp or fan)

Enter Zip Code:

Name Device:

Enter Wi-Fi Router Password:

DOWNLOAD

THE ECO APP:

(iOS 7 or higher) (Version 4 or higher)

SELECTING WHICH DEVICE TO CONTROL: If you have multiple ECO

Smart Boxes connected to the app, you can choose which device you

want to access (such as Master Bedroom, Home Office, etc.).

To select the device, slide the desired icon to the lower left position. The

ECO Smart Box name (such as “Master Bedroom,” below), will change

color from white to green. Chosen device is now able to be programmed or

edited, such as changing timer settings, updating cloud service, etc.

Note: You can connect to a maximum of twelve (12) ECO Smart Boxes via

the app. You can expand your system to include ECO surge protectors,

indoor or outdoor switches, and more!

TO RESET THE ECO SMART BOX: If you decide to connect this device to

a new router, or are having trouble setting up this device after multiple

attempts, try resetting the ECO Smart Box.

• Press and hold the Power button while atthe same time pressing the

Reset button with the tip of a toothpick or similar non-conductive item.

Continue holding the Power button for 3-5 seconds until the Wi-Fi Status

Indicator light turns off.

• When the Wi-Fi Status Indicator light turns off, release the Powerbutton

and the ECO Smart Box has been reset.

• After a few seconds the Wi-Fi StatusIndicator light will begin blinking

and the ECO Smart Box is ready to be reconnected to the Wi-Fi router via

the app.

This process removes any programmed settings, disconnects the app

connection to the Wi-Fi router, and restores the ECO Smart Box to the

factory default setting.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

INDUSTRY CANADA STATEMENT

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the remote receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.

Industry Canada Statement: This Class B digital apparatus complies with Canadian

ICES-003. This device complies with Industry Canada license exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

FCC and IC Radiation Exposure Statement: This equipment complies with FCC and

IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20cm

between the radiator and your body.

Contains FCC ID: PAGECO-PLUG

Contains IC: 4494A-ECOPLUGS

CAN ICES-3(B)/NMB-3(B)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with the instructions, may cause harmful inter-

ference to radio or television reception, which can be determined by turning the

equipment on and off. The user is encouraged to try to correct the interference by

one or more of the following measures:

Apple is a registered trademark of Apple Inc.

Android is a registered trademark ofGoogle Inc.

iOS is a trademark or registered trademark of Cisco in

the U.S.andother countries and is used under license.

Wi-Fi™ is a trademark of Wi-Fi Alliance®

Tap the More icon

FREQUENTLY ASKED QUESTIONS

Or send your

question

via email

Tap the FAQ link

TO ADD MULTIPLE USERS TO THE ECO OUTLET (Repeat steps below for

each additional user):

Link to the same home router

as used by first smartphone

or tablet

Tap the

ECO icon

Tap Settings

icon of

additional

user’s

smartphone

Tap the

Wi-Fi

icon

Choose a Network

Home Router

Other Router A

Other Router B

Add device

to the cloud

TO ACTIVATE CLOUD SERVICE

Tap

Settings

icon in the app

Cloud

status

inactive

Cloud status

activated

PROGRAMMING THE TIMER

Tap the

Timer icon

• Select the timer function from the list

• Select on/off times for desired hours,

minutes and days

• Tap the checkmark to accept

Click the arrow that appears on the

right of that setting to enter editing

mode.

EDITING THE TIMER PROGRAM

Tap the

Add icon

Tap the

Timer icon

Tap the

Edit icon

iOS:

Select the program to edit, tap and hold

until the edit pop-up window appears.

Tap the

Timer icon

Android:

Note: To remove cloud service, follow the same steps and tap Remove

device from the cloud.

Outdoor Wi-Fi Smart Box INSTALLATION INSTRUCTIONS

WARNING: This timer should be installed by a licensed electrician. Turn power off at main panel before servicing this switch or the

equipment it controls.

IMPORTANT: For outdoor use. Rain-tight or wet location conduit, hubs, tubing, and cable fitings that comply with requirements

of UL 514B must be used for installation.

Read Important Safety Information below before beginning installation.

Open outer cover by releasing the spring latch.

Remove the interior protective cover by removing the two screws holding the cover in place (Figure 1).

Select the knockouts to be used. Remove the inner 1/2” knockout by inserting a screwdriver in

the slot and carefully punching the knockout loose. Remove slug. If 3/4” knockout is required,

also remove the outer ring with pliers after removing the 1/2” knockout. Smooth any rough edges

with a file or sandpaper, if necessary.

Place the Smart Box in the desired mounting location and mark the location of the mounting

keyhole. Install a screw at mark and drive partially in place. Attach Smart Box by placing keyhole

over screw; then tighten screw firmly.

Wire in accordance with national and local codes (see wiring diagrams below). Use only copper

conductors, #8 AWG wire, suitable for at least 175° F (80° C). Tighten all connections to 12in-Ibf.

Grounding: Terminate all ground wires to grounding lug at the bottom of enclosure (Figure 2).

Replace interior protective cover.

Close outer cover. Smart Box is now ready to be connected to the WiFi router via the app.

Figure 1

Figure 2

Important Safety Information

WARNING: Risk of Fire or Electric Shock. Read instructions thoroughly before installation and preserve for future reference.

Disconnect power at circuit breaker and test that power is off before installing (or servicing) the Smart Box (more than one circuit breaker or disconnect switch may be

required to fully disconnect power).

Wiring must be in accordance with all national and local electrical code requirements. Inspect all terminals and wires with voltage meter before touching. The maximum total

load to be controlled must not exceed Smart Box capacity.