Ecoboil EBE Express Series User manual

Water boilers |Water chillers |Boil/Hot units |Boil/Hot/Chill units |Parts & Accessories
EBE Express Series
Automatic Under Bench Water Boilers
Installation and maintenance instructions
Please read prior to installation
Important
This unit must be installed by an authorised plumber
The unit to be connected in accordance with AS 3500.4.1
or AS/NZS 3500.4.2
Do not turn on power to this boiler until water is flowing
from the tap
Please leave these instructions with the owner
WHAT’S IN THE BOX:
1 x EBE Express Boiling Unit
1 x EBE 01 Express Boiling Tap
1 x EB FM 350 kPa PLV
1 x EB 316 Brass fitting kit
1 x Boiling Water Warning Label

Prior to installation
• Minimum Inlet Pressure 260 kPa
• We recommend the fitting of a water filter.
• Only teflon tape to be used where necessary. Under no
circumstances is plumbing paste to be used.
• When fitting this unit in a cupboard of small proportions, please
note that the unit does omit heat. If in doubt fit cross flow vents.
• Do not connect to the hot water line or the fire hydrant supply - to
do so will void the warranty.
Product Information
This unit is fitted with a computerised element and boil dry protection.
The computer is set at 95 Degrees C, altitude will alter the boiling
point.
• The 350 kPa Pressure Limiting Valve supplied must be fitted.
• If fitted with a filter, we recommend changing the cartridge every
12 months.
• The manufacturer recommends cleaning and servicing the unit
every 24 months, or every 12 months in hard water areas.
• If the supplied power cord is damaged, it must be replaced by an
electrician.
• The tap provided is a push through vented tap. After dispenser
water the tap will continue to dispense water until the spout is
empty. This ensure only water is dispensed each and every time.
Installation Instructions
1. Do not plug in the unit or turn on the power until the installation
process is complete.
2. Position the unit underneath the sink as close as possible to its
outlet tap location.
3. Position the tap in the desired location; drill a 40mm hole and
secure the tap firmly.
4. Observing the attached labels:
a. Measure and cut the pipes to the desired length. Do not
lengthen the copper pipes under any circumstances.
b. Connect the 1/4” pipe from the tap to the boiler inlet.

c. Connect the 5/16” pipe from the tap to the boiler outlet.
d. Connect the 1/4” pipe from the tap to the Mains water supply
using the 350 kPa PLV and brass connectors supplied.
e. Push the end of the silicon tube on to the vent pipe of the unit.
5. All pipes and tubes must not be extended and require a
continuous fall between tap and unit.
6. Open tap until water is flowing from the spout.
7. Once water flows out of the tap, plug in the unit to a standard 3
Pin 10 Amp Power Socket and switch on the power. Make sure
the unit is positively earthed.
8. After the power is turned on allow 20 minutes before testing and
using.
9. Check for leaks at all connections.
10. Position ‘Caution Boiling Water’ label close to the tap to alert
users to the water temperature.

Trouble Shooting
SYMPTOM CAUSES ACTION
Water overflowing
from tap spout
Expansion chamber
full
Low inlet pressure
Run tap for 5-10 minutes
Contact water supplier
Excessive steam
from tap
Faulty element Replace element
Water not hot No power supply
Faulty element
Check and test power supply
Replace element
No water Water has been
turned off
Blocked water filter
Check mains water supply
Replace filter cartridge
Water boilers |Water chillers |Boil/Hot units |Boil/Hot/Chill units |Parts & Accessories
For more information about Ecoboil and our products,
visit our website or contact us:
Ecoboil Appliances Limited
Phone [phone]
Fax [phone]
Mail P.O. Box 940, Pukekohe 2340
Web www.ecoboil.co.nz