VOKERA Linea User manual

Users
Instructions
THESE INSTRUCTIONS
TO BE RETAINED
BY USER
Linea ONE
High efficiency combi boiler
Vokèra is a licensed member of the Benchmark scheme
which aims to improve the standards of installation and
commissioning of domestic hot water systems in the UK.

2
Dear Customer
Your Linea One boiler has been designed to meet and exceed the very latest standards in gas central heating technology, and
if cared for, will give years of reliable use and efficiency.
Please therefore take some time to read these instructions carefully.
Do’s and Don’t’s
Do ensure that the system pressure is periodically checked
Do ensure that you know how to isolate the appliance in an emergency
Do ensure that you are familiar with the appliance controls
Do ensure that your installer has completed the appliance log book
Do not attempt to remove the appliance casing or gain internal access
Do not hang clothes etc. over the appliance
Do not forget to have the appliance serviced annually.
Contents
egaPnoitcudortnI
2remotsucraeD
2s’t’noddnas’oD
3noitamrofniyramirP
3noitamrofniyradnoceS
Things you should know Page
4secnailppasaG1.1
4ylppuslacirtcelE2.1
1.3 Guarantee registration card 4
4koobgolkramhcneB4.1
4?krowtiseodwoH5.1
4snoisnemiD6.1
4deriuqersecnaraelC7.1
4metsysnoitcetorptsorF8.1
4slortnoclanoitiddA9.1
egaPdetratsgnitteG
5nognihctiwserofeB1.2
5slortnocecnailppA2.2
5reliobehtgnithgiL3.2
2.4 Adjusting the operating temperatures 6
7sedoctluafyraropmeT5.2
7sedoctluaflaniF6.2
7edomnoitamrofnI7.2
How to...Page
3.1 Top-up the system pressure 8
8ecnailppaehtteseR2.3
3.3 Shut down the system for short periods 8
3.4 Shut down the system for long periods 8
8ecnailppaehtroferaC5.3
3.6 Regulate the hot water temperature 8
egaP...fitahW
9kaelsagatcepsusI1.4
4.2 I have to frequently to top-up the system 9
9nosithgilteserehT3.4
4.4 The appliance is due its annual service 9
9reenignenallacotdeenI5.4
INTRODUCTION

3
PRIMARY INFORMATION
CONTROLS INTERFACE
1
2
4
9
8
7
6
5
3
1 Info key
Enables the function that allows the access to some information
regarding the boiler operation.
2 Memory key
Enables the Memory function.
3 Heating temperature adjustment key
Allows the access to the adjustment of the heating water tem-
perature by using the selector.
4 ON/OFF/RESET key
Allows you to:
●switch on the boiler
●switch off the boiler
●restart the boiler after a fault stop.
5 Heating ON/OFF key
Enables/disables the heating function
6 Dedicated to the Technical Assistance Service
Enables or disables the boiler’s self-operation.
7 Encoder (adjustment selector)
Allows you to increase or decrease the preset values.
8 Comfort key
Enables Comfort function.
9 DHW temperature adjustment key
Allows the access to the adjustment of DHW temperature by
using the selector.
SECONDARY INFORMATION
DISPLAY
1 Reset symbol
Indicates when it is necessary to restart the boiler (please read
page 42 for details).
2 Key symbol
Indicates the presence of a fault (please read page 42 for
details).
3 Drop symbol
Displaying that the system pressure is under the correct level
4Displaying the operating temperature (DHW or heating).
5 Memory symbol
It is displayed when Memory function is on.
6 Heating symbol
Flashing, indicates a heating request in the room.
7 Heating layer
Indicates the position of the set heating temperature (position
relative to the maximum and minimum).
8When the heating flame is on, it indicates that the burner is on
following a heat request in the room.
9 Anti-freeze symbol
It is displayed when the anti-freeze function is on.
10 External probe symbol
It is displayed when the external probe is connected.
11 Remote control panel
It is displayed when a remote control panel is connected.
12 Service icon
Indicates the boiler is self-operating.
13 Pressure value of the heating installation.
14 Comfort symbol
It is displayed when the Comfort function is on.
15 DHW symbol
Flashing, indicates a DHW request.
16 DHW layer
Indicates the position of the DHW temperature set (position
relative to the maximum and minimum).
17 When the DHW flame is on, it indicates that the burner is on
following a DHW request.
°C
1
2
9
10
5
7
14
16
817
4
13
12
3
fig. 1
6
11
15

4
1.1 GAS APPLIANCE
Gas Safety (Installations and Use) Regulations.
In the interests of your safety and that of others it is a legal
requirement that all gas appliances are installed and correctly
maintained by a competent person and in accordance with the
latest regulations.
1.2 ELECTRICAL SUPPLY
Please ensure that this appliance has been properly connected to
the electrical supply by means of a double pole isolator or un-
switched socket, and that the correct size of fuse (3 AMP) has been
fitted.
Warning: this appliance must be earthed!
1.3 GUARANTEE REGISTRATION CARD
Please take the time to fill out your guarantee registration card. The
completed warranty card should be posted within 30 days of
installation.
1.4 BENCHMARK LOG BOOK
The Benchmark Log Book is supplied with your boiler. This
important document must be completed during the installation/
commissioning of your boiler. All GAS SAFE Registered Installers
carry a GAS SAFE ID card and have a registration number. Both
should be recorded in your
Benchmark Log Book. You can check
your installer by calling GAS SAFE direct on 08004085500. Failure
to install and commission the appliance in accordance with the
manufacturers instructions may invalidate the warranty. This does
not affect your statutory rights.
1.5 HOW DOES IT WORK?
Your Linea ONE boiler is a high efficiency combination boiler, which
supplies heated water to your radiators and hot water to your taps.
The central heating is controlled via a time clock and/or any ther-
mostats that your installer may have fitted. The boiler will light
when a hot water outlet (a tap) is opened. The boiler may also
function periodically to pre-heat the hot water heat exchanger. The
Linea ONE boiler lights electronically and does not have a pilot
light. In the unlikely event of a fault developing with your boiler, the
supply of gas to the burner will be terminated automatically.
1.8 FROST PROTECTION SYSTEM
The Linea ONE is equipped with a built-in frost protection system,
this enables the boiler to over-ride the time controls – if switched off
– and operate the burner and/or pump, should the temperature drop
below 7 °C.
Please note that the frost protection system is designed to protect
the appliance only, should frost protection be required for the central
heating system, additional controls may be required.
NOTE
The frost protection system is reliant on the appliance having a
permanent electrical supply, and being in a non-fault condition.
1.9 ADDITIONAL CONTROLS
Additional controls such as an external temperature sensor kit or
under floor heating safety thermostat are available as optional
accessories for this appliance. You should consult your installer
and/or the supplementary instructions supplied, on their use (if
installed).
THINGS YOU SHOULD KNOW
1.6 DIMENSIONS
HEIGHT
WIDTH
DEPTH
845 mm
453 mm
358 mm
1.7 CLEARANCES REQUIRED
ABOVE
BELOW
SIDES
FRONT
150 mm
120 mm
(Left =12 mm / Right = 25mm)
600 mm

5
2.1 BEFORE SWITCHING ON
Before switching the appliance on please familiarise your-
self with:
- how to isolate the appliance from the gas, water and electricity
supplies;
- how to check and top-up – if necessary – the system water
pressure;
- any external thermostats/time switches and their functions;
- the appliance controls.
2.2 APPLIANCE CONTROLS (see fig. 1)
The appliance controls are on the front cover.
The appliance is equipped with a simple control panel that can
be used to alter or control the following functions:
- ON/OFF selection;
- mode of operation;
- the outlet flow temperature to the central heating system;
- the outlet temperature for domestic hot water.
In addition, the large LCD display shows the status of the appliance:
- current mode of operation;
- current appliance temperature;
- current temperatures selected;
- current system water pressure.
The system water pressure display shows the current pressure of
the system, and when the appliance is operating the display may
rise or fall, this is quite normal. The minimum permissible level for
the safe and efficient operation of the appliance is 0.6 BAR. Should
the pressure fall below 0.6 BAR, the boiler may lockout.
Depending on the type of controls specified by your installer you
may have an external time clock or programmer fitted, please refer
to the instructions supplied with such.
2.3 LIGHTING THE BOILER
Ensure the electrical supply to the appliance is switched on. Press
the ON/OFF switch to switch the appliance ON (indicated by active
display), ensure any external controls are switched to an ‘ON’
position and are calling for heat.
After being powered, the boiler begins an automatic vent cycle
lasting approximately 2 minutes. The display indicates “sf” and the
“function selection indicators” light up in sequence. Press the
MODE button to interrupt the automatic vent cycle.
Press the heating button, the appliance will now operate in the
Heating mode.
2.3.1 MODES OF OPERATION
When the appliance is switched ON one of two modes of operation
can be selected:
- boiler “ON” (heating mode on);
- boiler “OFF” (heating mode off - domestic hot water on).
BOILER “ON” IN HEATING MODE
When boiler is in the
Heating position, the appliance is active for
both heating and DHW requests.
The booster function and pre-heat function are active.
BOILER“OFF”(heating mode off - domestic hot water on)
When the function switch is in the DHW position, the appliance is
active for DHW requests.
The TSC (Temperature Stability Control) function is active. All
heating requests will be ignored.
2.3.2 FUNCTIONS
- TSC: when the TSC function is active the appliance may over-
ride the selected DHW temperature in order to maintain
temperature stability.
- Comfort button: by pressing the button, Comfort function
enables and the correspondent symbol is displayed.
By pressing the button, domestic hot water is supplied at the
ideal temperature for shower; the
standard temperature set is actually
40 °C.
It is possible to modify Comfort tem-
perature from 35 °C to 45 °C with a
0,5 °C correction. In order to change
this temperature, after selecting the
function, press the button and turn
the selector A.
The set temperature is displayed.
Comfort function avoids searching
for the right mix between hot and
cold water in order to obtain the right
temperature for shower.
Note
The value set is memorized by the
boiler, so that, the next time you
select Comfort button, the boiler
should be ready to supply the water at the desired temperature.
-Memory key: by pressing the button, Memory function
enables and the correspondent
symbol is displayed.
Memory function simultaneously
enables a double electronic
intelligence:
• domestic hot water intelligence
• heating intelligence.
DHW Memory
By enabling Memory button, the
intelligence of the machine begins
to memorize the usage habits of
the user. After only one week,
Memory function would have
already learned the user’s habits
of using domestic hot water and
therefore should be able to pre-
heat it for each request.
The pre-heating is performed in the
half hour before the request made in the day and at the hour
memorized the week before.
Example
Thursday 15th at 7.00 a.m. a domestic hot water request is made.
Next Thursday, the 22nd, at 6.30 a.m., the boiler performs the pre-
heating of domestic hot water.
When the user makes the hot water request at 7.00 a.m., finds the
water already at the desired temperature.
If it is necessary to have pre-heated water besides the usual
habits, please use the Touch & Go function.
In case the boiler lacks power supply, the data memorized by
this function will be lost. When the boiler is power supplied again,
Memory function restarts to memorize the habits. In order to
benefit by the advantages off Memory function, you have to wait
for one week to pass.
CH Memory
By enabling Memory button, the boiler takes in consideration the
time that passes from ignition and after 10 minutes increases the
delivery temperature memorized with 5 °C.
Memory repeats the cycle until the room temperature set on the
room thermostat is reached or until the maximum temperature
allowed is reached.
Due to this automatic function, it is possible to select lower
delivery temperatures and at the same time to reduce the time for
reaching the set room temperature.
⇒ page 8
GETTING STARTED
A
Comfort button
Memory button
fig. 2
fig. 3

6
LINEA ONE is a combi boiler, fully condensing with a premix burner.
The boiler is characterized by very low emission, high modulation and top domestic hot water performance.
The above characteristics allow the boiler to maximize the end user comfort and maximize the energy saving both on the gas and the
electricity.
Button for central heating set point
Use this button to allow the encoder to set the central heating temperature set
point.
H.T.C. function: while adjusting the heating temperature, from the minimum value
40°C to the maximum value 80°C, the field where the H.T.C. system enables is
met: Heating Temperature Control (from 55°C to 65°C).
The H.T.C. system autonomously manages the delivery temperature,
adapting the boiler’s operation to meet the dwelling’s real needs.
When the heat need extends, the delivery temperature increases
allowing a faster heating of the environment.
Once the desired comfort is reached, the system restores the delivery temperature
to the value set at the beginning. All this assures minor consumptions, minor
limestone deposits in the boiler and minor thermal ranges in the radiators.
Info button
By pressing the key, the InFO word appears on display. By turning the selector
A, the display shows, one by one, the information described below.
Info list
Info 1 displays the external temperature recorded by the probe, only if an external
probe is connected
Info 2 displays the system pressure
Info 3 displays the set heating temperature
Info 4 displays the set domestic hot water temperature.
If you don’t make any selection within 10 seconds, the boiler automatically exits
the function; if you want to exit immediately, press the key.
Memory button
Memory key: by pressing the button, Memory function enables and the
correspondent symbol is displayed.
Memory function simultaneously enables a double electronic
intelligence:
- domestic hot water intelligence
- heating intelligence.
Domestic hot water Memory
By enabling Memory button, the intelligence of the boiler begins to memorize the
usage habits of the user. After only one week, Memory function would have
already learned the user’s habits of using domestic hot water and therefore
should be able to pre-heat it for each request.
The pre-heating is performed in the half hour before the request
made in the day and at the hour memorized the week before.
Central heating Memory
By enabling Memory button, the boiler takes in consideration the time that passes
from ignition and after 10 minutes increases the delivery temperature memorized
with 5 °C.
Memory repeats the cycle until the room temperature set on the
room thermostat is reached or until the maximum temperature allowed is
reached.
Due to this automatic function, it is possible to select lower delivery temperatures
and at the same time to reduce the time for reaching the set room temperature.
KNOWING THE LINEA ONE

7
°C
ON/OFF/RESET
Pressing this button the boiler:
- Switch on the boiler
- Switch off the boiler
- Reset in case of alarms
Central heating ON/OFF
Pressing this button the central heating is activated or deactivated (winter/
summer function). Domestic hot water is supplied all the time.
Service button
This button is dedicated only for servicing to adjust the boiler in local, switching
off the remote control in case it is connected.
Encoder
This knob allows you to increase or decrease the selected parameters
Comfort button: by pressing the button, Comfort function enables and the
correspondent symbol is displayed.
By pressing the button, domestic hot water is supplied at the ideal temperature
for shower; the standard temperature set is actually 40 °C. It is possible to modify
Comfort temperature from 35 °C to 45 °C with a 0,5 °C correction. In order to
change this temperature, after
selecting the function, press the button and turn the selector A. The set
temperature is displayed. Comfort function avoids searching for the right mix
between hot and cold water in order to obtain the right temperature for shower.
Note
The value set is memorized by the boiler, so that, the next time you select Comfort
button, the boiler should be ready to supply the water at the desired temperature.
Domestic hot water temperature selection
Press the key and turn the selector A to select desired domestic hot water
temperature. The big digits will light up on display, indicating the selected
temperature value. After a few seconds the display will show again the delivery
temperature, effectively recorded by the boiler’s probe.
Touch & Go Function: if you don’t wish to keep the Memory function always
enabled or if you need hot water to be ready fast besides the usual habits
memorized, it is possible to perform the domestic hot water pre-heating only a
few moments before the request.
Due to Touch & Go function, by turning on and off the tap the instantaneous pre-
heating function enables, which prepares hot water only for that request.
fig. 4

8
- H.T.C. function: while adjusting the heating temperature, from the
minimum value 40°C to the
maximum value 80°C, the field
where the H.T.C. system enables is
met: Heating Temperature Control
(from 55°C to 65°C).
The H.T.C. system autonomously
manages the delivery temperature,
adapting the boiler’s operation to
meet the dwelling’s real needs.
When the heat need extends, the
delivery temperature increases
allowing a faster heating of the
environment.
Once the desired comfort is reached,
the system restores the delivery temperature to the value set at the
beginning. All this assures minor consumptions, minor limestone
deposits in the boiler and minor thermal ranges in the radiators.
- Touch & Go Function: if you don’t wish to keep the Memory
function always enabled or if you need hot water to be ready fast
besides the usual habits memorized, it is possible to perform the
domestic hot water pre-heating only a few moments before the
request.
Due to Touch & Go function, by turning on and off the tap the
instantaneous pre-heating function enables, which prepares hot
water only for that request.
- Frost-protection: this function is only active when there are no
requests for heating or HW. Should the temperature of the pri-
mary thermistor drop below 7°C, the boiler will operate to reduce
the risk of frost damage
- ANTI-BLOCK: the anti-block function is active at all times even
when the appliance ON/OFF selector is at OFF. Should the
appliance be inactive for 24-hours, both the pump and divertor
valve actuator will be energised for a short period to reduce the
risk of component seizure.
NOTE
The frost protection and anti-block functions are reliant on the
appliance having a permanent electrical supply, and being in a
non-fault condition.
2.3.3 HEATING MODE
Press the button to select the heating mode: the display will
show boths layers.
When there is a demand for heating via the time clock etc, the boiler
will go through an ignition sequence, whereby the burner will light.
When the appliance reaches the set temperature, the burner will go
off for minimum period of approximately 5minutes.
When the programmer/time clock or external thermostats heating
request has been satisfied, the appliance will switch off automatically.
2.3.4 DHW MODE
Press the key to select the DHW mode: the display will show
only the DHW layer.
When a hot water outlet or tap is opened, the boiler senses water
flow and initiates an ignition sequence. The boiler will modulate
the output according to the temperature required, when the hot
water request has been satisfied, the boiler may continue to ope-
rate if the pre-heat function is active.
NOTE
If the appliance fails to ignite during the ignition sequence, it will
re-attempt ignition several times before going to a lockout condition.
Should this occur, please allow a period of two minutes before re-
setting.
H.T.C. function
2.4 ADJUSTINGTHEOPERATINGTEMPERATURES(seefig.1)
2.4.1 ADJUSTING HEATING TEMPERATURE
If you want to adjust the temperature value, by increasing or
decreasing, proceed as follows:
- press the heating temperature adjustment key , the number
corresponding to the heating temperature will appear on the two
digits
- turn the encoder to increase or decrease the value.
After three seconds last modified the value is automatically stored.
After a few seconds the display will show again the heating tempe-
rature, effectively recorded by the boiler’s probe
2.4.2 ADJUSTING HEATING TEMPERATURE WITH AN
EXTERNAL PROBE CONNECTED
When an external probe is connected, the value of the delivery
temperature is automatically chosen by the system which rapidly
adjusts the room temperature according to the variations in external
temperature.
The external probe symbol appears on the display and just the
central segment of the heating bar lights up.
If you want to adjust the temperature value, by increasing or
decreasing it given the value automatically calculated by the
electronic board, proceed as follows:
- press the heating temperature adjustment key , the number
corresponding to the set comfort level will appear on the two
digits (standard setting)
- turn the encoder to increase or decrease the comfort level (the
number corresponding to the selected comfort level will appear
on the two digits +1, +2 etc or -1, -2 etc).
The illuminated segment of the heating bar will increase or
decrease. Correction tolerance lies between - 5 and + 5 comfort.
These corrections are very important between seasons, when the
value calculated by the curve could result too low and therefore
the time for reaching the set room temperature could be too long.
After 3 seconds from the last adjustment, the value is automatically
memorized and the display shows again the value recorded
instantaneously by the probe.
2.4.3 ADJUSTING THE HOT WATER TEMPERATURES (see
fig.1)
Press the key and turn the selector A to select desired domestic
hot water temperature. The big digits will light up on display,
indicating the selected temperature value.
After a few seconds the display will show again the delivery tem-
perature, effectively recorded by the boiler’s probe.
fig. 5

9
2.5 TEMPORARY FAULT CODES
The built-in fault diagnostic system automatically displays a unique
fault code that can be used to determine why the boiler has
temporarily locked out. When the boiler displays a temporary fault
code, the appropriate code is shown flashing on the display,
accompanied by the symbol .
2.6 FINAL FAULT CODES
When the boiler displays a final fault code, the appropriate code is
shown flashing on the display, accompanied by the symbol
(RESET).
2.6.1 CODE ERROR + (RESET) ONLY
To reset the boiler, push button. If the boiler starts without any
problems, the lock-out is probably due to an accidental situation.
2.6.2 CODE ERROR + (RESET) +
Refer to the following section and the detailed fault finding flow-
charts overleaf.
Code Reason
11 false flame
12 restart ignition
13 check the wiring harness
23 check the wiring harness
25 high limit flow temperature probe
27 high limit return temperature probe
41 low water pressure
60 DHW NTC error
71 flow NTC error (2nd CH)
77 over heat underfloor thermostat (2nd CH)
78 flow/return ΔT error (2nd CH)
Code Reason
10 no flame detected
14 check the wiring harness
15 false flame
20 high limit thermostat/fume thermostat
21 check the wiring harness
22 check the wiring harness
24 high limit flow temperature probe
26 high limit return temperature probe
28 flow/return ΔT error
29 check the wiring harness
34 fan error (start-up)
37 fan error (high rpm)
40 low water pressure
42 pressure transducer fault
50-59 internal PCB failure
70 flow NTC error (2nd CH)
72 return NTC error (2nd CH)
79 flow/return ΔT error (2nd CH)
80-83 internal fault
91 condensing heat exchanger cleaning requirement
2.7 INFORMATION MODE
The appliance keypad can be used to display certain information
on the working status of the boiler. Push the Info button , the InFO
word appears on display. By turning the selector A, the display
shows, one by one, the information described below.
Info list (fig. 6)
Info 1 displays the external temperature recorded by the probe,
only if an external probe is connected
Info 2 displays the system pressure, accompanied by the filling
symbol
Info 3 displays the set heating temperature
Info 4 displays the set domestic hot water temperature.
If you don’t make any selection within 10 seconds, the boiler
automatically exits the function; if you want to exit immediately,
press the key.
fig. 6

10
3.1 HOW TO TOP-UP THE SYSTEM PRESSURE (fig. 7)
The system pressure must be checked periodically to ensure
the correct operation of the boiler. The display should ideally be
reading between 0.6 (minimum) and 1.5 (maximum) when the
boiler is in an off position and has cooled to room temperature.
If the pressure requires ‘topping-up’ use the following instruc-
tions as a guide.
●Locate the filling valve connections (beneath the boiler).
●Attach the filling loop to both connections.
●Open the filling valve slowly until you hear water entering the
system.
●Close the filling valve when the displayed pressure (on the
boiler) reads between 1 and 1.5.
●Remove the filling loop from the connections.
3.2 HOW TO RESET THE APPLIANCE
When the display is flashing, or when the reset icon is shown,
the appliance will require to be reset manually. Before resetting
the boiler ensure that the displayed pressure is indicating the
correct level. Allow a period of two minutes to elapse before
pressing the reset button.
IMPORTANT
If the appliance requires to be reset frequently, it may be
indicative of a fault, please contact your installer or Vokera
Customer Services for further advice.
3.3 HOW TO SHUT DOWN THE SYSTEM FOR SHORT
PERIODS
The system and boiler can be shut down for short periods by
simply turning the time clock to the off position. It is also
advisable to turn off the main water supply to the house.
3.4 HOW TO SHUT DOWN THE SYSTEM FOR LONG
PERIODS
If the house is to be left unoccupied for any length of time –
especially during the winter – the system should be thoroughly
drained of all water.
The gas, water, and electricity supply to the house should also
be turned off. For more detailed advice contact your installer.
3.5 HOW TO CARE FOR THE APPLIANCE
To clean the outer casing use only a clean damp cloth. Do not
use any scourers or abrasive cleaners.
3.6 HOW TO REGULATE THE HOT WATER TEMPERATURE
Usually your installer will have adjusted the hot water output
to suit your requirements, however if you would like to adjust
the outlet temperature, please follow the instructions in section
2.4.
NOTE
If you find that the hot water temperature is still insufficient,
try reducing the flow of water through the tap.
normal
operating
position
filling
position
closed
position
Hot water outlet
Cold water inlet
stopcock/filling
valve
Gas
cock
Filling loop
C/H flow
valve
C/H return
valve Safety
valve outlet
HOW TO...
fig. 7
fig. 8

11
4.1 WHAT IF I SUSPECT A GAS LEAK
If you suspect a gas leak, turn off the gas supply at the gas
meter, and contact your installer or local gas supplier. I you
require further advice please contact your nearest Vokera
office.
4.2 WHAT IF I HAVE FREQUENTLY TO TOP-UP THE
SYSTEM
If the system regularly requires topping-up, it may be indicative
of a leak. Please contact your installer and ask him to inspect
the system.
4.3 WHAT IF THE RESET LIGHT IS ON
If the reset icon is shown, it indicates that the boiler has failed
to ignite or has overheated, when this happens the boiler
automatically shuts down and requires to be reset manually
(see 3.2).
4.4WHAT IFTHE APPLIANCE IS DUE ITS ANNUAL SERVICE
Advice for tenants only
Your landlord should arrange for servicing.
Advice for homeowners
Please contact Vokera Customer Service (0844 391 0999 (UK)
or 05655057 (ROI) if you would prefer a Vokera service
engineer or agent to service your appliance. Alternatively your
local GAS SAFE registered engineer may be able to service the
appliance for you.
4.5 WHAT IF I NEED TO CALL AN ENGINEER
If you think your boiler may have developed a fault please
contact your installer or Vokera Customer Services (0844 391
0999 (UK) or 05655057 (ROI) have all your details to hand
including full address and postcode, relevant contact numbers,
and your completed appliance log book.
WHAT IF...

Cod. 20023653 - 07/10 - Ed. 0
Registered address:
Vokèra Ltd
Borderlake House
Unit 7 Riverside Industrial Estate
London Colney
Herts AL2 1HG
[email protected]
www.vokera.co.uk
www.vokera.ie
Sales, General Enquires
T 0844 391 0999
F 0844 391 0998
Vokèra Ireland
West Court, Callan
Co Kilkenny
T 056 7755057
F 056 7755060
Vokèra Limited reserve the right to change
specification without prior notice
Consumers statutory rights are not affected.
A Riello Group Company.
Company Reg No: 1047779