EcoxGear SOUNDEXTREME ACC-SEJV6 User manual

UNIVERSAL GOLF CAR MOUNTS
User Guide | Model: ACC-SEJV6
These Universal Golf Car Mounts allow for a secondary mounting
position for all SoundExtreme Powersports Amplified Soundbars
onto a 1” x 1” square tube. Please read all of the instructions before
you begin installing your soundbar.
Mounting
Instructions
1. In order to properly space
out the J-Hook Mounts, first
loosely attach them onto the
¼-20 mounting rail on the top
of your soundbar.
2. Next hold your soundbar
up to the horizontal, 1” x 1”
square tube that you plan on
mounting it to.

3. Once you have marked the desired mounting location, lay down
the 3” Rubber Strip. The Rubber Strip will cover the 3 flat sides that
the J-Hook makes contact with the horizontal, square tube.
4. Slide the J-Hook Mounts over each Rubber Strip on the horizontal,
square tube.
Note: The J-Hook Mounts can be positioned above or below the
square tube, based on how much clearance you have with the roof
of your golf car.
5. The Rubber Strips are designed to fit tightly between the J-Hook
Mounts and the square tube. If you having trouble sliding the
J-Hook Mounts onto the Rubber Strips while the Mounts are
attached to the soundbar, it may be easier to remove them from
the soundbar and install them one at a time.
6. Once the J-Hook Mounts are installed on the square tube,
secure each into position with the M8 1.25 x 50mm Bolt, 2
Washers, and 1 Nut.
Square Tube Rubber Strip
J-Hook Mount
Locknut and
M8 Washer
M8 Bolt and
M8 Washer

7. Next, you can mount your
soundbar to the 2 (or
more) J-Hook Mounts
that you have installed
using the supplied ¼-20
Bolt and Washer.
8. Be sure to tighten all of
your hardware securely
in order to finish your
installation.
Specifications
Dimensions
Unit Weight
0.55 lbs (each)
Mount Thickness
Approximately 0.19 in / 4.8 mm
4.75 in / 120.7 mm
1.49 in / 37.9 mm
1.48 in / 37.6 mm
¼-20 Bolt and
¼-20 Washer

What’s in the Bag
CAUTION:
This mounting bracket is designed for light-duty, on-road driving applications. If your installation is for an o-road
vehicle (UTV/ATV/4x4) used in high-impact driving conditions, please see our website for heavy-duty mounting options
recommended for your vehicle.
LIMITED MANUFACTURER’S WARRANTY:
The Universal Golf Car Mounts are covered by a 1-year limited warranty that covers defects in workmanship and / or
materials for a period of 1 year from original purchase date. This warranty does not apply to any products which have
been abused, neglected, modified or used for a purpose other than the one for which they were manufactured. The
warranty is valid only for the original owner who purchases the unit from an authorized dealer. Transfers do not qualify
for warranty protection. Grace Digital reserves the right to replace any out-of-stock or discontinued product with a
comparable product. Discontinued products may not be available for warranty replacement. Any contents are NOT
covered by the limited manufacturer’s warranty. Warranty terms may be revised without notification at the discretion of
the manufacturer. Please visit www.ecoxgear.com for additional product & warranty information.
Universal Golf Car Mounts by ECOXGEAR, a division of Grace Digital Inc., San Diego, California.
Designed in California. Made in China.
(2x) M8-1.25 Nylon
Insert Locknut
(2x) 1/16” Thick x 1”
Wide x 3” Length
EPDM Rubber Strip
(4x) M8 Flat Washer(2x) M8-1.25 x 50mm
Long BHSC Bolt
(2x) ¼-20 x 0.75”
Long SHCS Bolt
(2x) ¼-20 Washer
(2x) J-Hooks