Arjo KWIKtrak 700.11900 User manual

001-11900-EN rev 5 • 08/2019
INSTRUCTIONS FOR USE
KWIKtrak Semi-Permanent Rack
Model Nº 700.11900

Design Policy and Copyright
® and ™ are trademarks belonging to the Arjo group of companies.
© Arjo 2019.
As our policy is one of continuous improvement, we reserve the right to
modify designs without prior notice. The content of this publication may not
be copied either whole or in part without the consent of Arjo.

001-11900-EN rev. 5
Table of Contents 1
Table of Contents
Foreword ......................................................................................................................................2
Thank you for choosing Arjo products. .................................................................................................... 2
Please Read this Manual Thoroughly!..................................................................................................... 2
Service and Support ................................................................................................................................ 2
Manufacturer Information......................................................................................................................... 2
Denitions Used in this Manual ............................................................................................................... 2
Safety Instructions ......................................................................................................................3
Operational Life ....................................................................................................................................... 3
Equipment Identication .......................................................................................................................... 3
General Instructions................................................................................................................................. 3
How to Use this Manual........................................................................................................................... 3
Safe Working Load .................................................................................................................................. 4
Important Safety Instructions................................................................................................................... 4
Environmental Advice .............................................................................................................................. 4
Homecare Environment Considerations.................................................................................................. 4
Symbols Used..............................................................................................................................5
General Symbols ..................................................................................................................................... 5
Product Description ....................................................................................................................6
Semi-Permanent Rack System Requirements..........................................................................7
Floor Requirements: ................................................................................................................................ 7
Room Assessment .....................................................................................................................7
Assembling the Semi-Permanent Rack.....................................................................................8
Post - Top Assembly ............................................................................................................................... 8
Post - Base Assembly (Leg) .................................................................................................................... 8
Assembling the Track onto First Post ...................................................................................................... 9
Inserting the Lift into the Track............................................................................................................... 10
Assembling the Track onto Second Post ............................................................................................... 10
Final Adjustments .................................................................................................................................. 10
Installing the Charger Station .................................................................................................................11
Care and Maintenance .............................................................................................................12
Preventive Maintenance Schedule ........................................................................................................ 12
Annual Inspection by an Authorized Technician .................................................................................... 12
Cleaning................................................................................................................................................. 12
Troubleshooting ........................................................................................................................13
Technical Specications...........................................................................................................14
Dimensions............................................................................................................................................ 14

001-11900-EN rev. 5
Foreword2
Foreword
Thank you for choosing
Arjo products.
Your KWIKtrak™ Semi-Permanent Rack is part of
a series of quality products designed specially for
home care, nursing homes and other health care
uses.
We are dedicated to serving your needs and
providing the best products available along with
training that will bring your staff maximum benet
from every Arjo product.
If a serious incident occurs in relation to this medical
device, affecting the user, or the patient then the
user or patient should report the serious incident
to the incident to the medical device manufacturer
or the distributor. In the European Union, the
user should also report the serious incident to the
Competent Authority in the member state where
they are located.
Please Read this Manual Thoroughly!
The information in this manual is crucial to the proper
use and maintenance of the Semi-Permanent Rack.
It will help protect your product as well as ensure
that it performs to your satisfaction.
Lifting and transferring a person always presents a
potential risk. This manual contains safety related
information that must be read and understood to
help prevent injuries.
WARNING: Arjo strongly advises and warns
that to avoid injuries that can be attributed to the
use of inadequate parts, only parts designated
by Arjo should be used on product and other
appliances supplied by Arjo.
WARNING: Unauthorized modications on any
Arjo product may affect its safety. Arjo will not be
held responsible for any accidents, incidents or
lack of performance that occur as a result of any
unauthorized modication to its products.
The equipment must be installed in accordance with
these safety instructions.
Anyone installing the equipment must also have
read and understood the instructions in this manual.
If there is anything you are not sure about, contact
the local Arjo representative.
Do not attempt to service or repair the
Semi-Permanent Rack. If any item is defective,
contact your local Arjo vendor.
Service and Support
A service routine must be done on your
Semi-Permanent Rack by Arjo trained service
personnel. This will ensure it remains safe and
functional.
Please contact your local Arjo vendor for any of the
following:
• If you require further information.
• If you want to report an unexpected event,
change in the performance or a malfunction.
• If you need any help in setting up, using or
maintaining your Semi-Permanent Rack.
• If you need replacement parts.
Your Arjo vendor can offer support and service
programs to maximize the long-term safety, reliability
and value of the product.
Additional copies of this manual can be purchased
from your local Arjo agent. When ordering, include
the Instructions for Use part number (see front
page).
Manufacturer Information
This product was manufactured by:
ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
 : [phone]
: [phone]
ü: www.Arjo.com
Denitions Used in this Manual
WARNING:
Means: Failure to understand and follow this
instruction may result in injury to yourself and others.
CAUTION:
Means: Failure to follow this instruction may cause
damage to the product(s).
NOTE:
Means: Important information regarding correct use
of the product.

001-11900-EN rev. 5
Safety Instructions 3
Intended Use
The Semi-Permanent Rack is a portable track
system to be used with Arjo ceiling lift in a homecare
setting, at nursing homes and other assisted living
centres. Patient transferring is performed under
the supervision of a trained caregiver as per the
instructions outlined in this manual.
WARNING: The Semi-Permanent Rack is
for transferring patients only. Do not use the
Semi-Permanent Rack for any other purpose.
Using this Semi-Permanent Rack outside the
scope of its intended use could lead to injuries.
Operational Life
This product is designed and tested for a useful life
of seven (7) years or 10 000 transfers —whichever
comes rst—at maximum safe working load (SWL).
It is subject to preventive maintenance as specied
in the "Care and Maintenance" section.
Time equivalence between the number of transfers
versus the number of years is explained in the
following table.
Transfers per Day Years
(10 000 transfers)
47
6 4.5
8 3.5
WARNING: The manufacturer cannot ensure full
safety for a product of which the life span has
been exceeded. Wear may cause the breakage
of a part and lead to a patient fall.
The life span is the safe operating time period before
a complete overhaul is required.
The following factors have an impact on the
Semi-Permanent Rack life span:
• aging of the unit;
• transfers per day;
• weight of the patient;
• maintenance frequency.
A transfer is dened as the displacement of a patient
from one point to another. A transfer cycle includes
a lifting and a descending action.
Equipment Identication
The unit’s identication number (specication,
model, serial number) appears on a silver
nameplate attached inside the track of the KWIKtrak
Semi-Permanent Rack.
General Instructions
Keep these safety instructions with the KWIKtrak
Semi-Permanent Rack at all times. Read the
assembly instructions before installing or servicing
this equipment.
WARNING: Two persons are required to carry
out this assembly safely.
Assembling the Semi-Permanent Rack without
being assisted could lead to injuries.
How to Use this Manual
To ensure the safe operation of the
Semi-Permanent Rack, read the entire manual
carefully before operating this product.
If anything is not completely understood, please
contact your local Arjo agent for more details.
Failure to comply with warnings in this manual may
result in injuries.
Keep this manual handy and refer to it as required.
Make sure that all operators are regularly trained in
the use of the product as per the information found
therein.
The Semi-Permanent Rack must be used as per
these safety instructions.
Anyone using the Semi-Permanent Rack must also
have read and understood the instructions in this
manual.
Foreword Safety Instructions

001-11900-EN rev. 5
Safety Instructions4
Safe Working Load
CAUTION: The Safe Working Load of the
Semi-Permanent Rack is determined by the
track, style and length, mounted on the rack (see
the table below).
Maximum Track Length VS
Capacity and Track Style
Semi-
Permanent
Rack Maximum
Capacity
H90 H140 H180
Maximum Track Length
200 kg (440 lb) 3 m 4.5 m 6 m
272 kg (600 lb) 3.5 m 4.5 m
454 kg (1000 lb) 3.5 m
WARNING: The Semi-Permanent Rack is
intended to be used for residents whose weight
is within a specied safe working load (SWL). Do
not attempt to lift more than the lowest weight
limit indicated on the following:
• the Semi-Permanent Rack see table above
• the “maximum load” label on the ceiling lift
• on the spreader bar
• on the sling.
Overloading any of these elements could lead to
a patient fall.
Important Safety Instructions
Before installing or using the Semi-Permanent Rack
always ensure to comply with the following safety
instructions:
WARNING: The assembling/disassembling
procedure must be performed by two persons.
Failure to follow this instruction may result in
serious injuries to yourself and others.
• All the parts must be used. Do not
leave any out (except plastic cap ends
according to the type of track).
• Make sure the track installation
will accept the load.
• The equipment is used by trained staff.
• All labels are legible and those that
cannot be easily read are replaced.
• The daily maintenance is carried
out before using the unit.
• Never use the Semi-Permanent Rack
system as a swing.
• Always refrain from swinging
patient sideways on the track.
Environmental Advice
When disposing of any items associated with the
product, contact local authorities for information.
Homecare Environment
Considerations
WARNING: The Semi-Permanent Rack is not
intended to be operated by children. Serious
injuries could occur.
NOTE: Rigorous cleaning should be done when
the Semi-Permanent Rack is exposed to an
animal. Pet hair trapped inside the track can
reduce the product’s performance.
Symbols Used

001-11900-EN rev. 5
Symbols Used 5
General Symbols
Manufacturer’s name and
address. May also point
out manufacturing date.
CE marking indicating conformity
with European Community
harmonised legislation.
REF Points out the manufacturer’s
catalogue number.
Indicates a potential risk,
refer to Instructions for Use
(IFU) for details.
SN Points out the manufacturer’s
serial number.
SWL SWL is the maximum load the
device is rated for safe usage.
1641
Refer to the Instructions for Use.
Incorrect
Correct
Indicates the product is a
Medical Device according
to the EU Medical Device
Regulation 2017/745.
Symbols Used

001-11900-EN rev. 5
Product Description6
Product Description
Fig. 1
17
13
14
15
18
16
12
1
2
6
7
8
910
11
3, 4, 5
Item Part № Description Quantity
1 250.11060 LEG END CAP (WHITE) 4
2 000.00379 LEG SUPPORT “NON-SLIP” 3/8-16 X 1 1/4″ 4
3 000.00375 SCREW 3/8-16 X 1 1/4 ZINC 2
4 000.00425 LOCK WASHER 3/8 ZINC 2
5 225.11455 PUCK 2
6 200.11415 NEOPRENE PROTECTIVE PAD 200.10410 4
7 250.11460 LEG 2
8 225.11425 TOP STEEL PART 2
9 203.11435 PRESSURE STEEL PART 2
10 700.11005 TRACK END STOPPER 2
11 225.11405 “T” BRACKET 4
12 250.11470 POST 2
13 200.11060 RAIL END CAP (WHITE) 4
14 000.04553 M12 X 30 SOCKET LOW HEAD ZINC 4
15 000.04910 LOCK WASHER M12 ZINC 4
16 000.04295 M10 X 75 HEX ZINC 4
17 000.04350 M10 X 110 HEX ZINC 8
18 000.04410 LOCKNUT M10 ZINC 12
The track must be ordered separately:
Ordering Part № per Track Length
Track Type Track Length Part №
H90 3 m 200.12810
H140 3.5 m 200.12872
4.5 m 200.12870
H180
3.5 m 200.12882
4.5 m 200.12884
6 m 200.12880

001-11900-EN rev. 5
Semi-Permanent Rack System Requirements 7
Floor Requirements:
CAUTION: If you are unsure of the strength or stability of the oor – do not install the Semi-Permanent Rack
– consult your local Arjo agent.
• Flooring must comply to local building code standards.
WARNING: Termites or water damages may affect the structure of the oor.
• Floor must be clear of any
dust, grease, water or any
foreign substance.
• Floor must have a slope of
less than 0.5°. See "Fig. 2" to
determine the oor slope. Use
a level or contact a contractor
if unsure of oor slope.
Fig. 2
X
Y
X Y
600 mm (24”) 5.2 mm (3/16”)
900 mm (36”) 7.9 mm (5/16”)
1200 mm (48”) 10.5 mm (7/16”)
Semi-Permanent Rack System Requirements
Room Assessment
Before installing the Semi-Permanent Rack prepare the installation as follows:
1) Survey the room where you plan to install the Semi-Permanent Rack.
• Make sure the room meets all the specications outlined in
"Semi-Permanent Rack System Requirements" section.
2) Make sure the pick-up point will be inside the transfer zone:
• Over a bed :
approximately 915 - 1020 mm (36 - 40”) from the head of the bed.
• Over a tub:
approximately 400 - 460 mm (16 - 18”) from the end of the tub.
• Allow 1000 mm (39”) of the open area for transfer working space.
3) Determine the location for the two posts considering that
transfers should only take place between the posts of the
Semi-Permanent Rack system.
Fig. 3
400 - 460 mm
(16 - 18’’)
915 - 1020 mm
(36 - 40’’)
Bed
Bath
tub
Ø 1 m (39”)
Ø 1 m (39”)

001-11900-EN rev. 5
Assembling the Semi-Permanent Rack8
Post - Top Assembly
Fig. 4
000.04295
M10 X 75 HEX ZINC
000.04410
LOCKNUT M10 ZINC
000.04910
LOCKWASHER
M12 ZINC
000.04553
M12 X30 SOCKET LOW
HEAD ZINC
PRESSURE PLATE
TRACK BRACKET
Note: The pressure plates are preassembled to the
track brackets at the factory.
1) For your convenience, make sure the assembly
complies with "Fig. 4", check for the following:
• Pressure plates are attached to the
track brackets using two M12 X 30 low
head 9 mm socket (zinc) bolts.
• Both lock washers are present on each
assembly and were placed at proper location.
• Pressure plates orientation. Plates
mate with track brackets.
2) Fasten one track bracket onto top of post, using
two M10 X 75 hex zinc bolts and corresponding
locknuts.
3) Tighten using a 17 mm socket tool or hexagonal
key. Recommended torque: 20 N·m.
4) Repeat procedure for second post.
Post - Base Assembly (Leg)
Fig. 5
000.04410
LOCKNUT M10 ZINC
000.04350
M10 X110 HEX ZINC
1) Place one post perpendicular with the centre of
one leg as shown in "Fig. 5".
2) Attach one “T” plate on each side of post using
two M10 X 75 hex zinc bolts and corresponding
locknuts.
3) Tighten and secure the screws with the locknut.
Use 17 mm socket tools or hexagonal keys.
4) Tighten using a 17 mm socket tool or hexagonal
key. Recommended torque: 20 N·m.
5) Install caps on both ends of leg.
6) Repeat procedure for second post.
Assembling the Semi-Permanent Rack

001-11900-EN rev. 5
Assembling the Semi-Permanent Rack 9
Assembling the Track onto First Post
Note for H140 tracks:
Referring to "Fig. 6", taking
note of how the track
should be oriented to be
in the proper position.
Fig. 6
1) Insert one end stopper into the track lower
channel.
Fig. 7
2) Install the track between the Track bracket and
the pressure plate onto top of rst post.
Fig. 8
3) Make sure the track is ush with the back of the
bracket.
Fig. 9
12
4) Fasten the assembly by tightening the two bolts
located inside the track bracket
Fig. 10
5) Secure the end stopper in place.
Fig. 11
6) Install a cap at end of track.
Fig. 12

001-11900-EN rev. 5
Assembling the Semi-Permanent Rack10
Inserting the Lift into the Track
NOTE: Before proceeding to this step, make sure
that the second post is assembled and ready to
receive the track.
1) Insert the lift or portable trolley into the track.
2) Raise the track slightly to assure that the lift will
not roll back out of the track.
Fig. 13
3) Insert the second stopper inside the track, but
do not tighten it.
Fig. 14
Assembling the Track onto Second Post
1) Insert the track onto the second post assembly
following the same instructions as for the rst
post (see previous page).
2) Fasten the assembly by tightening the two bolts
located inside the track bracket. Use the two
M12 X 30 socket low head zinc screws with
appropriate lock washers.
Fig. 15
3) Secure the end stopper in place.
Fig. 16
4) Install a plastic cap at the of the track.
Final Adjustments
1) Reposition the end stoppers in order to prevent
the lift from hitting the posts, or to reduce the
transfer area according to your needs. (eg. if
you do not want the lift to access the left portion
of the track, secure the right stopper in the
middle of the track.
2) Stabilize the Semi-Permanent Rack by adjusting
the two legs supports. To do so, unscrew the leg
supports in order to put them in contact with the
oor.
3)
WARNING: The load must always be applied on
the large centre puck located under each leg.
The non-slip leg supports are only designed to
stabilize and balance the rack. They must not
support any direct load (see "Fig. 17").
Fig. 17
Floor level
Floor level
Weight is on
center puck
Weight is not on
center puck

001-11900-EN rev. 5
Assembling the Semi-Permanent Rack 11
Installing the Charger Station
This section does not apply for tracks using portable
lifts.
1) Determine the best suitable location for the lift
to be placed when it is not being used.
2) Align the bottom hooks of the charger station
clip to the lower groove on the track.
3) Push on the top portion of the charger station
clip to make it snap onto the track.
4) Route the charger cable onto the upper track
channel and connect it to an AC power plug.
Fig. 18
1
2
3

001-11900-EN rev. 5
Care and Maintenance12
Troubleshooting
Preventive Maintenance Schedule
The Semi-Permanent Rack is subject to wear and the following actions must be performed when specied
to ensure that the product remains within its original manufacturing specication.
WARNING: The points on this checklist are the minimum the manufacturer recommends. In some cases
more frequent inspections should be carried out. Continuing to use the Semi-Permanent Rack without
conducting regular inspections will seriously compromise the user's and patient’s safety. Preventive
maintenance specied in this manual can prevent accidents.
WARNING: Safety related maintenance and authorized service must be carried out by qualied
personnel, fully trained in servicing procedures by Arjo and equipped with correct tools and proper
documentation, including the parts list and service manual. Failure to meet these requirements could
result in personal injuries and / or unsafe equipment.
POINTS TO BE INSPECTED BY
USER / SERVICE TECHNICIAN
FREQUENCY
Annually or 1400 cycles
Monthly
Before every use   
Inspect for evidence of external damage or missing parts. 
Make sure all bolts and nuts are properly tightened.  
Make sure that bases are properly adjusted. 
Make sure track is properly assembled to the posts.
Make sure that all posts are straight. 
Clean the inside of the tracks to ensure there is no dust or grease build-up inside the tracks.  
Check to make sure that the trolleys move freely along the tracks.  
WARNING: If any of the above inspection point fails, DO NOT USE the Semi-Permanent Rack until
appropriate corrective action is taken.
Annual Inspection by an Authorized Technician
The Semi-Permanent Rack must be inspected by a qualied Arjo technician on an annual basis to ensure
the proper functioning of its components, as well as the safety of the patients and care givers that use the
Semi-Permanent Rack. Please contact your local representative to make arrangements.
NOTE: If the product does not work as intended, immediately contact your local Arjo agent for support.
Cleaning
To clean the Semi-Permanent Rack, wipe it down with a damp cloth using warm water and mild detergent.
CAUTION: Do not use phenol, chlorine or any other type of solvent that may damage the nish.
To ensure a better rolling surface for the trolley wheels, clean the inside of the track every four months. To
do so, insert a damp cloth in the opening and slide it from one end of the track to the other.
Care and Maintenance

001-11900-EN rev. 5
Troubleshooting 13
PROBLEM TO CHECK
Trolley moves substantially
on its own when the
Semi-Permanent Rack
is fully assembled.
• Is the track levelled?
• Is the oor levelled?
• Is the track secured to the posts? Press up on the track
to make sure that it is correctly xed onto posts.
Trolley does not roll
in track smoothly.
• Is track clean? Clean track with damp cloth.
• Is trolley centred in track? Re-centre trolley.
• Is the trolley damaged? Replace trolley
Posts and bases rock
back and forth
• Check integrity of the oor.
• Are the levellers properly adjusted?
• Are the posts properly assembled with the base?
Troubleshooting
Care and Maintenance

001-11900-EN rev. 5
Technical Specications14
Technical Specications
PRODUCT INFORMATION Semi-Permanent Rack № 700.11900
Weight Total: 53 kg
Post: 16.5 kg (each)
Base: 10 kg (each)
Max. safe working load
Material Tracks: Aluminium
Hardware: Steel, plastic
END OF LIFE DISPOSAL
Package Cardboard recyclable
The Product Components that are primarily be made up of different kinds of metal
(containing more than 90% metal by weight) should be recycled as metal.
Dimensions
Fig. 19
3000 mm
3500 mm
4500 mm
6000 mm
1300 mm
2331.4 mm
(90 mm track)
2388.4 mm
(140 mm track
2424.4 mm
(180 mm track)
www.arjo.com
AUSTRALIA
Arjo Australia Pty Ltd
78, Forsyth Street
O’Connor
AU-6163 Western Australia
Tel: [phone]
Free: [phone]
Fax: + 61 89337 9077
BELGIQUE / BELGIË
Arjo NV/SA
Evenbroekveld 16
BE-9420 ERPE-MERE
Tél/Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
BRASIL
Arjo Brasil Equipamentos Médicos Ltda
Rua Marina Ciufuli Zanfelice, 329 PB02 Galpão
- Lapa
São Paulo – SP – Brasil
CEP: 05040-000
Phone: [phone]
E-mail: [e-mail]
E-mail: [e-mail]
CANADA
Arjo Canada Inc.
90 Matheson Boulevard West
Suite 300
CA-MISSISSAUGA, ON, L5R 3R3
Tel/Tél: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [e-mail]
ČESKÁ REPUBLIKA
Arjo Czech Republic s.r.o.
Na Strzi 1702/65
140 00 Praha
Czech Republic
Phone No: [phone]
e-mail: [e-mail]
DANMARK
Arjo A/S
Vassingerødvej 52
DK-3540 LYNGE
Tel: [phone]
Fax: [phone]
E-mail:
[e-mail]
DEUTSCHLAND
Arjo GmbH
Peter-Sander-Strasse 10
DE-55252 MAINZ-KASTEL
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
ESPAÑA
Arjo Ibérica S.L.
Parque Empresarial Rivas Futura, C/Marie
Curie 5
Edificio Alfa Planta 6 oficina 6.1-.62
ES-28521 Rivas Vacia, MADRID
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
FRANCE
Arjo SAS
2 Avenue Alcide de Gasperi
CS 70133
FR-59436 RONCQ CEDEX
Tél: [phone]
Fax: [phone]
E-mail: [e-mail]
HONG KONG
Arjo Hong Kong Limited
Room 411-414, 4/F, Manhattan Centre,
8 Kwai Cheong Road, Kwai Chung, N.T.,
HONG KONG
Tel: [phone]
Fax: [phone]
ITALIA
Arjo Italia S.p.A.
Via Giacomo Peroni 400-402
IT-00131 ROMA
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
MIDDLE EAST
Arjo Middle East FZ-LLC
Office 908, 9th Floor,
HQ Building,North Tower,
Dubai Science Park,
Al Barsha South
P.O Box 11488, Dubai,
United Arab Emirates
Direct [phone]
Fax [phone]
Email: [e-mail]
NEDERLAND
Arjo BV
Biezenwei 21
4004 MB TIEL
Postbus 6116
4000 HC TIEL
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
NEW ZEALAND
Arjo Ltd
34 Vestey Drive
Mount Wellington
NZ-AUCKLAND 1060
Tel: [phone]
Free Call: 0800 000 151
Fax: [phone]
E-mail: [e-mail]
NORGE
Arjo Norway AS
Olaf Helsets vei 5
N-0694 OSLO
Tel: [phone]
Faks: [phone]
E-mail: [e-mail]
ÖSTERREICH
Arjo GmbH
Lemböckgasse 49 / Stiege A / 4.OG
A-1230 Wien
Tel: [phone]
Fax: [phone]
POLSKA
Arjo Polska Sp. z o.o.
ul. Ks Piotra Wawrzyniaka 2
PL-62-052 KOMORNIKI (Poznań)
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
PORTUGAL
Arjo em Portugal
MAQUET Portugal, Lda.
(Distribudor Exclusivo)
Rua Poeta Bocage n.º 2 - 2G
PT-1600-233 Lisboa
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
SUISSE / SCHWEIZ
Arjo AG
Fabrikstrasse 8
Postfach
CH-4614 HÄGENDORF
Tél/Tel: [phone]
Fax: [phone]
SUOMI
Arjo Scandinavia AB
Riihitontuntie 7 C
02200 Espoo
Finland
Puh: [phone]
E-mail: [e-mail]
SVERIGE
Arjo International HQ
Hans Michelsensgatan 10
SE-211 20 MALMÖ
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
UNITED KINGDOM
Arjo UK and Ireland
Houghton Hall Park
Houghton Regis
UK-DUNSTABLE LU5 5XF
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
USA
Arjo Inc.
2349 W Lake Street Suite 250
US-Addison, IL 60101
Tel: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [e-mail]
JAPAN
Arjo Japan K.K.
東京都港区虎ノ門三丁目 7番8号 ランディッ
ク第 2 虎ノ門ビル 9 階
電話：[phone]
Address page - REV 24: 04/2019

Technical Specications
www.arjo.com
AUSTRALIA
Arjo Australia Pty Ltd
78, Forsyth Street
O’Connor
AU-6163 Western Australia
Tel: [phone]
Free: [phone]
Fax: + 61 89337 9077
BELGIQUE / BELGIË
Arjo NV/SA
Evenbroekveld 16
BE-9420 ERPE-MERE
Tél/Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
BRASIL
Arjo Brasil Equipamentos Médicos Ltda
Rua Marina Ciufuli Zanfelice, 329 PB02 Galpão
- Lapa
São Paulo – SP – Brasil
CEP: 05040-000
Phone: [phone]
E-mail: [e-mail]
E-mail: [e-mail]
CANADA
Arjo Canada Inc.
90 Matheson Boulevard West
Suite 300
CA-MISSISSAUGA, ON, L5R 3R3
Tel/Tél: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [e-mail]
ČESKÁ REPUBLIKA
Arjo Czech Republic s.r.o.
Na Strzi 1702/65
140 00 Praha
Czech Republic
Phone No: [phone]
e-mail: [e-mail]
DANMARK
Arjo A/S
Vassingerødvej 52
DK-3540 LYNGE
Tel: [phone]
Fax: [phone]
E-mail:
[e-mail]
DEUTSCHLAND
Arjo GmbH
Peter-Sander-Strasse 10
DE-55252 MAINZ-KASTEL
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
ESPAÑA
Arjo Ibérica S.L.
Parque Empresarial Rivas Futura, C/Marie
Curie 5
Edificio Alfa Planta 6 oficina 6.1-.62
ES-28521 Rivas Vacia, MADRID
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
FRANCE
Arjo SAS
2 Avenue Alcide de Gasperi
CS 70133
FR-59436 RONCQ CEDEX
Tél: [phone]
Fax: [phone]
E-mail: [e-mail]
HONG KONG
Arjo Hong Kong Limited
Room 411-414, 4/F, Manhattan Centre,
8 Kwai Cheong Road, Kwai Chung, N.T.,
HONG KONG
Tel: [phone]
Fax: [phone]
ITALIA
Arjo Italia S.p.A.
Via Giacomo Peroni 400-402
IT-00131 ROMA
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
MIDDLE EAST
Arjo Middle East FZ-LLC
Office 908, 9th Floor,
HQ Building,North Tower,
Dubai Science Park,
Al Barsha South
P.O Box 11488, Dubai,
United Arab Emirates
Direct [phone]
Fax [phone]
Email: Info.[email protected]
NEDERLAND
Arjo BV
Biezenwei 21
4004 MB TIEL
Postbus 6116
4000 HC TIEL
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
NEW ZEALAND
Arjo Ltd
34 Vestey Drive
Mount Wellington
NZ-AUCKLAND 1060
Tel: [phone]
Free Call: 0800 000 151
Fax: [phone]
E-mail: [e-mail]
NORGE
Arjo Norway AS
Olaf Helsets vei 5
N-0694 OSLO
Tel: [phone]
Faks: [phone]
E-mail: [e-mail]
ÖSTERREICH
Arjo GmbH
Lemböckgasse 49 / Stiege A / 4.OG
A-1230 Wien
Tel: [phone]
Fax: [phone]
POLSKA
Arjo Polska Sp. z o.o.
ul. Ks Piotra Wawrzyniaka 2
PL-62-052 KOMORNIKI (Poznań)
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
PORTUGAL
Arjo em Portugal
MAQUET Portugal, Lda.
(Distribudor Exclusivo)
Rua Poeta Bocage n.º 2 - 2G
PT-1600-233 Lisboa
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
SUISSE / SCHWEIZ
Arjo AG
Fabrikstrasse 8
Postfach
CH-4614 HÄGENDORF
Tél/Tel: [phone]
Fax: [phone]
SUOMI
Arjo Scandinavia AB
Riihitontuntie 7 C
02200 Espoo
Finland
Puh: [phone]
E-mail: [e-mail]
SVERIGE
Arjo International HQ
Hans Michelsensgatan 10
SE-211 20 MALMÖ
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
UNITED KINGDOM
Arjo UK and Ireland
Houghton Hall Park
Houghton Regis
UK-DUNSTABLE LU5 5XF
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
USA
Arjo Inc.
2349 W Lake Street Suite 250
US-Addison, IL 60101
Tel: [phone]
Free: [phone] Institutional
Free: [phone] Home Care
Fax: [phone]
E-mail: [e-mail]
JAPAN
Arjo Japan K.K.
東京都港区虎ノ門三丁目 7番8号 ランディッ
ク第 2 虎ノ門ビル 9 階
電話：[phone]
Address page - REV 24: 04/2019

Page intentionally left blank

Page intentionally left blank

At Arjo, we are committed to improving the everyday lives of people affected by reduced mobility and age-related health challenges.
With products and solutions that ensure ergonomic patient handling, personal hygiene, disinfection, diagnostics, and the effective
prevention of pressure ulcers and venous thromboembolism, we help professionals across care environments to continually raise
the standard of safe and dignied care. Everything we do, we do with people in mind.
ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
www.arjo.com
Langues:
#Ref:
001-11900-ZH
001-11900-TR
001-11900-RU
001-11900-PT
001-11900-PL
001-11900-NO
001-11900-NL
001-11900-JA
001-11900-KO
001-11900-IT
001-11900-HR
001-11900-HE
001-11900-FR
001-11900-ES
001-11900-EN
001-11900-EL
001-11900-DE
001-11900-DA
001-11900-SV
001-11900-CS
001-11900-
ZH
NO PT RUPL
ES
SVKOJA
HEDE IT
FREN
NL
HRCS DA EL
TR