EcoxGear GDI-EXJMP1500 User manual

Models: GDI-EXJMP1500...1520
User Guide
EcoJump

2 3
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference
that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
reorient or relocate the receiving antenna, increase the separation between the equipment
and receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, consult the dealer or an experienced radio/TV technician for help.
RF WARNING STATEMENT:
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
IC STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1) This device may not cause interference, and
2) This device must accept any interference, including interference that may
cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and Follow all Instructions. Use only as intended.
The ECOXGEAR device is intended to be used indoors or outdoors and in land or water
environments. The device has been tested to IP67 waterproofing standards. However, the
device is not intended for constant underwater use.
Always make sure the cap(s) / covers(s) are clean, free from sand or debris and correctly
fitted. The device will only meet IP67 ratings if all rubber seals, gasket(s) and cap(s) /
covers(s) are in place. If your device is exposed to salt water clean it thoroughly after use with
fresh water.
The USB cables, connections, and the unit with an improperly fitted or closed cap are
NOT waterproof.
To prevent fire or shock, do NOT attempt to charge this unit if it is wet or you suspect
water has entered the unit. In this situation, please return the unit to Grace Digital for a free
assessment. If we have found that the unit has carried water we will repair or replace the unit
free of charge.
SAFETY ADVISORY & WARNING:
Read and Follow all Instructions. Use only as intended.
CAUTION: Do NOT open to repair. A qualified technician must carry out repair work.
ATTENTION: Do NOT charge while the unit is wet. Towel dry the unit AND make sure all
connections are dry BEFORE plugging in the charging connector. Failure to do
so may result in electrical damage to the unit and may void the warranty.
WARNING: This product may contain chemicals listed in Proposition 65
(www.oehha.ca.gov/prop65/prop65_list/Newlist.html)
WARNING: The unit has a built-in Lithium battery. The battery must NOT be used in or
near an open heat source or excessive heat.
WARNING: Danger of explosion if battery is incorrectly replaced.
ATTENTION: Do NOT dispose of in a landfill. Contact Grace Digital at
www.gracesupport.com or a certified recycling agent to dispose of the unit.
ATTENTION: AC adapter is a device forming a part of the main plug therefore the AC
adapter can always be readily disconnected from AC socket-outlet.
WARNING: When using this product, basic precautions should always be followed,
including the following:
a) To reduce the risk of injury, close supervision is necessary when the
product is used near children.
b) Use of an attachment not recommended or sold by power
pack manufacturer may result in a risk of fire, electric shock, or injury
to persons.
c) Do not operate the power pack with a damaged cord or plug, or a
damaged output cable.
SAVE THESE INSTRUCTIONS

4 5
SAFETY:
This product has a limited life span of use and should be replaced when it shows obvious
signs of wear.
Do not modify or remove any original component parts of the device. Doing so could cause
damage to the unit allowing water to ingress. A unit with water ingress should not be charged
due to potential risk of fire or shock.
Do not attempt to mount the unit except with the approved ECOXGEAR mounts. Doing so
could cause damage to the unit allowing water to ingress. A unit with water ingress should
not be charged due to potential risk of fire or shock.
You should always
1) Use the proper ECOXGEAR mounts if you intend to mount the unit.
2) Properly seal the ECOXGEAR prior and after each use when in humid or water
environments to avoid water damage to the internal components. Salt water / air is
particularly corrosive. Always make sure that the gaskets are sealed when in a salt water
environment and the unit properly rinsed off after use.
3) Properly clean the ECOXGEAR and ensure the gaskets have no sand, dirt or water on
them prior to storage or removing the cover.
4) Store your unit with all caps properly sealed to avoid long term internal moisture damage
inside your unit.
5) Completely dry and clean your ECOXGEAR prior to attempting to charge the unit.
6) Return the ECOXGEAR to Grace Digital if you suspect water ingress into the unit or if
the unit has experienced a severe impact that may have affected the integrity of the unit
to take on water.
You should never
1) Never charge your ECOXGEAR if you suspect water has entered the device. Charging a
device with water inside could be potentially hazardous and cause fire or a spark.
2) Never use your ECOXGEAR if you have dropped it or thrown it against a hard surface,
which may have destroyed the integrity of the housings, or gaskets. In the event
of a severe impact to your unit please return the unit to Grace Digital to review for
potential damage.
3) Never open the auxiliary doors in a water environment. This could cause water to ingress
into the unit, which could potentially be hazardous and cause a fire or a spark.
4) Never attempt to fix, repair your ECOXGEAR unit. Please send it back to Grace Digital for
any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
1) The unit is waterproof only when the caps are properly closed.
2) Close the caps properly before use. If the unit is placed in water without the caps properly
closed, water may enter into the unit and void your warranty.
3) Dry unit completely before opening the caps. Do NOT open the caps if wet or in a
wet environment.
4) Do NOT apply excessive force to any surfaces of the unit when wet or in a
wet environment.
5) Do NOT use or store the unit in places with high temperature.
6) AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong
magnetic fields.
7) Periodically check the rubber seal on the caps for premature wear.
8) Periodically clean the rubber with a soft moist cloth and ensure no objects such as
dirt, hair, or sand are on the rubber seal ring. Do NOT use any oily solvent or chemicals
for cleaning.
9) Rinse off the unit with tap water after use in salt water or swimming pool.
10) Power and / or charge the built-in rechargeable battery by connecting the USB cord to
a computer USB connection or to the AC outlet using the AC-to-USB cord 5V, 2A power
adapter intended for use with the unit.
11) Do NOT remove the built-in battery.

06 07
Control Buttons & Operations On/Off
Unit will arrive powered
OFF. PRESS AND HOLD
the Power Button for
approximately 2 seconds
to power ON.
When ON, SHORT PRESS to
put in Standby Mode. Short
press again to turn unit ON.
Keep in Standby Mode when
unit is not in use to enable
battery notifications.
When ON or in Standby
Mode, PRESS AND HOLD for
approximately 4 seconds to
power OFF.
NOTE: The Bluetooth battery
level and temperature
notifications do NOT work
when EcoJump is OFF. Refer
to BLE and Smartphone App
for details.
Power Indicator:
• Solid BLUE Light - ON.
• Slow BLUE Flashing -
Standby Mode.
• Rapid BLUE Flashing -
Refer to Extreme
Temperature Mode
for details.
• No Light - OFF.
LED Flashlight
Press the LED Button once
to cycle through four modes:
LOW, HIGH, SOS, OFF.
!
READY TO JUMP
DISCONNECT!
RECHARGE ECOJUMP
STATUS
JUMP START INSTRUCTIONS:
1. RED Clamp to (+) Terminal
2. BLACK Clamp to (-) Terminal
3. Insert Jump Start Cable
4.Press Power Button
5. Check Status Lights
POWER
PRESS:
FLASHLIGHT
HOLD:
HAZARD OVERRIDE
Override
Indicator
Power
Indicator Hazard Light Status Lights
Battery Level Indicator
PRESS AND HOLD to turn
the hazard light ON/OFF.
NOTE: Unit must be ON for
lights to function.
Override
Use this function with
EXTREME caution. Refer to
Low-Voltage Vehicle Batteries
& Manual Override for details.
Override Indicator:
• Rapid RED Flashing -
Override Mode.
• No Light - Normal
Operating Mode.
Status Lights
READY TO JUMP:
Solid GREEN Light -
EcoJump is ready to jump
start your battery.
DISCONNECT!:
Something is connected
incorrectly - Disconnect the
clamps immediately!
• Flashing RED Light -
EcoJump is likely shorted.
You must ensure clamps are
not touching each other.
• Solid RED Light - EcoJump
is likely connected with
reverse polarity. You must
verify that the RED
& BLACK clamps are
connected to the positive
& negative battery
terminals, respectively.
Jump Start Cables
Plug
Clamps

08 09
Jump Starting Your Vehicle
CAUTION: Do
NOT attempt
to jump start if
unit and/or
connections are
wet or damp.
To access the jump start
connection on the side of
your EcoJump, pull tab on
the rubber cap that reads,
"ENGINE START." Once the
rubber cap is removed, the
jump start connection will
be exposed.
Carefully read and understand
the vehicle owner’s manual
on specific precautions and
recommended methods for
jump starting the vehicle.
Make sure to determine the
voltage and chemistry of the
battery by referring to your
battery owner’s manual prior
to using this product. The
EcoJump is for jump starting
standard vehicle 12V
lead-acid batteries only.
Connecting to
the Battery
Prior to connecting to your
battery, verify that it is a
12V lead-acid battery. The
EcoJump is not suitable for
any other type of battery.
Identify the correct polarity
of the battery terminals on
the battery. The positive and
negative battery terminals
are typically marked by the
following letters or symbols,
respectively: (POS, P, +),
(NEG, N, -). Do NOT make
any connections to the
carburetor, fuel lines, or thin,
sheet metal parts. The
instructions below are for a
negative ground system.
If your vehicle is a positive
ground system (very
uncommon), follow Steps 1
and 2 in reverse order.
Connect the positive,
RED, clamp to the
positive (POS, P, +)
battery terminal.
Connect the negative,
BLACK, clamp to the
negative (NEG, N, -)
battery terminal or
vehicle chassis.
PUSH TO SEAL
About EcoJump
The EcoJump is a portable & waterproof lithium jump
starter for vehicles with 12V lead-acid batteries (cars, trucks,
boats, ATVs, motorcycles, etc.). It is designed for easy & safe
use, with built-in reverse polarity & short circuit protection.
The EcoJump has clearly labeled & easy to understand
buttons, indicator lights, and connection ports. The EcoJump
also provides live updates to your phone, via Bluetooth
Low Energy, on the charge & temperature status of your
EcoJump, ensuring the unit is ready for use when needed
most! The EcoJump can be used up to 20 times on a single
charge to jump start most 12V battery vehicles. It also has
the convenience of two 5V USB ports for charging your
smartphone and other devices, a 200 Lumen flashlight, and
an emergency warning light.
NOTE: The EcoJump comes partially charged out of the box
but needs to be fully charged prior to use.
1
2
RECHARGE ECOJUMP:
Solid YELLOW Light - Your
EcoJump battery level is
too low to use the jump
start function. You must
recharge before attempting
to use as a jump starter.
NOTE: The EcoJump
can connect to your
smartphone using BLE
(Bluetooth Low Energy)
to inform you when your
battery is running low.
Extreme Temperature Mode:
DISCONNECT! Solid RED AND
RECHARGE ECOJUMP Solid
YELLOW - Refer to Extreme
Temperature Mode for details.
Battery Level Indicator
Each BLUE LED bar represents
20% of a charge. Five full LEDs
indicate a full charge. When
the EcoJump battery level is
below 15%, the first LED bar
will flash slowly.

10 11
The EcoJump is designed
to jump start 12V lead-acid
batteries with voltage
readings down to 3.2V. If
your vehicle battery is below
3.2V, the READY TO JUMP
LED will be OFF (even after
connecting correctly to
the POS and NEG battery
terminals). This is an
indication that the EcoJump
cannot detect a battery.
If you need to jump start a
battery below 3.2V, there is
a Manual Override feature,
which allows you to force ON
the jump start function.
CAUTION: Use this mode
with EXTREME CARE. This
mode is for 12V lead-acid
batteries only.
Both the spark proof and
reverse polarity protection
features are disabled in
Override Mode.
Pay very close attention to
the polarity of the battery
before using this mode. Do
NOT allow the positive and
negative jump start clamps
to touch or connect to each
other as the product will
generate sparks. This mode
uses very high current (up
to 600 Amps) that can
cause sparks and high heat
if not used properly. If you
are unsure about using this
mode, do NOT attempt and
seek professional help.
Low-Voltage Vehicle Batteries &
Manual Override - Use With Caution
period. Allow the EcoJump
to rest for ten minutes
before attempting to jump
start the vehicle again.
Once you have started
your vehicle, press the
Power Button on the
EcoJump to put it in
Standby Mode, unplug
the Jump Start Cables
7
NOTE: When disconnecting,
disconnect in the reverse
sequence, removing the
negative clamp first.
Jump Start
Connect the Jump Start
Cables to the EcoJump.
Press the Power Button
to turn ON EcoJump unit,
when in Standby Mode
(if the EcoJump is OFF,
PRESS AND HOLD the
Power Button to turn ON).
The Battery Level
Indicator lights and Power
Indicator light will
illuminate to show the
unit is on and ready for
use. If you are connected
to a 12V battery, one of
the Status Lights will
also illuminate:
• READY TO JUMP:
GREEN light ON means
EcoJump is ready to
jump start your battery.
• DISCONNECT!:
Something is connected
incorrectly - Disconnect
the clamps immediately!
RED light flashing
means EcoJump is
likely short circuited. RED
light ON means EcoJump
is likely connected with
reverse polarity.
• RECHARGE ECOJUMP:
YELLOW light ON means
your EcoJump battery
level is too low to use the
jump start function.
You must recharge before
attempting to use as a
jump starter.
If the (GREEN) READY TO
JUMP LED is lit, you are
ready to proceed.
Make sure all of the
vehicle’s power loads
(headlights, radio, air
conditioning, etc.) are
turned off before
attempting to jump start
the vehicle.
Try starting the vehicle.
Most vehicles will start
immediately; however,
some vehicles may
require the EcoJump to
be connected for up to
30 seconds before
starting. If the vehicle does
not start right away, wait
20-30 seconds before
trying again. Do NOT
attempt more than three
consecutive jump starts
within a ten-minute
3
4
from the EcoJump
unit, and disconnect the
jump start clamps from
your vehicle (removing
the negative, BLACK,
clamp first). Remove the
EcoJump from the vehicle
engine compartment and
store in a safe place in your
vehicle, home, or office.
6
5

12 13
Before using the Manual
Override feature, make sure
the Jump Start Cable plug is
connected to the EcoJump
and the jump start clamps
are connected to the correct
polarity battery terminals.
To use the Manual Override
feature, PRESS AND HOLD
the Override Button . The
READY TO JUMP LED and
Override Indicator LED will
flash, indicating you have
successfully entered into
Manual Override Mode and
it is ready to jump start
your vehicle.
Most vehicles will start
immediately; however, some
vehicles may require the
EcoJump to be connected
for up to 30 seconds before
starting. If the vehicle does
not start right away, wait
20-30 seconds before trying
again. Do NOT attempt more
than three consecutive jump
starts within a ten-minute
period. Allow the EcoJump
to rest for ten minutes before
attempting to jump start the
vehicle again.
Press the Power Button
to exit Override Mode and
enter Standby Mode.
CAUTION: Place your
EcoJump in Standby Mode
before disconnecting the
jump start clamps. This
will ensure your safety.
Remember, both the spark
proof and reverse polarity
protection features are
disabled in Override Mode.
CAUTION: Do NOT attempt
to jump start if unit and/or
connections are wet or damp.
Important: Maintaining Waterproofness
If the caps are not properly closed, your EcoJump is NOT
watertight. To ensure the unit is watertight & waterproof,
ALWAYS CLOSE THE CAPS PROPERLY.
In order to ensure the unit is watertight, close rubber caps
& PUSH along the EDGE of the RUBBER so that the caps
are flush with the surface of the unit.
USB Charging Connections
To access the charge
connections on the EcoJump,
pull tab on the rubber cap.
Input
Connect the USB cable to the
USB micro Input to charge
your EcoJump.
RECOMMENDATION: Use
the USB cable and power
adapter included in the box.
NOTE: Charge time from low
to full charge is approx. 7 hrs.
CAUTION: Do NOT charge if
unit and/or connections are
wet or damp.
Output
Connect to one of the USB
Output (5V, 2.1A & 5V, 2.1A)
ports to charge your
personal device. Use the
USB cable included with
your personal device.
NOTE: Charging rates are
similar to the charging rate
when connected to the USB
of a desktop PC.
Charge time is approx. 1.5 hrs.
from low to full for most
smartphones; however, charge
times will vary depending on
the device being charged, the
device’s battery specifications,
and the device features. In
some instances, your personal
device may not indicate if a
charge is in process.
CAUTION: Do NOT charge if
unit and/or connections are
wet or damp.
OUTPUTS
INPUT

14 15
BLE and Smartphone App
Extreme Temperature Mode
Bluetooth Low Energy
While your EcoJump is ON
or in Standby Mode, it will
communicate its battery
level and temperature via
Bluetooth Low Energy (BLE)
to nearby smartphones.
Download the EcoJump
App to your smartphone.
The App is available on the
Apple App Store and the
Google Play Store.
NOTE: The Bluetooth battery
notifications do NOT work
when EcoJump is OFF.
EcoJump App
The EcoJump is App
connected and provides live
updates on the EcoJump
battery charge level and
temperature to your
smartphone. The EcoJump
uses Bluetooth Low Energy
Environmental
As an added safety
precaution, in situations
where the EcoJump battery
is exposed to extreme
temperatures (above 122°F
or below 0°F), the EcoJump
will turn off all charge out
and charge in functions
until the battery returns to
a temperature within its
safe operating range. The
EcoJump Power Indicator
will flash rapidly when in this
Extreme Temperature Mode.
Extensive Use
If the EcoJump has been
used extensively for multiple
jump start attempts (10+)
within a short period of
time, the unit may start to
get hot. If the EcoJump ever
exceeds a safe operating
temperature range, built-in
safety protection circuitry
will automatically turn the
jump start function off,
the DISCONNECT! and
RECHARGE ECOJUMP
Status Lights will illuminate
(solid RED and YELLOW),
and the jump start
connection port will become
inactive. After a period of
time has passed to allow the
EcoJump to cool down, the
Status Lights will turn off and
the jump start connection will
automatically re-activate.
to send data to the EcoJump
App on your smartphone
whenever your smartphone
is within range - typically
about 30-60ft. You can
configure the App to display
pop-up warnings on your
smartphone whenever the
battery charge level has
dropped below a given level
or if the EcoJump unit is
outside the recommended
storage temperature range.
These warnings sent to your
smartphone help to ensure
the EcoJump will be fully
charged and ready for use
when needed most.
NOTE: On iOS devices,
the EcoJump App
must be running in the
background for the pop-
up warnings to display on
your smartphone.
When the unit is in Standby
Mode, the battery will stay
over 50% charged for up to 6
months. To optimize charge
level while in storage, PRESS
AND HOLD the Power
Button for approximately
4 seconds to power OFF. In
OFF mode, the EcoJump
will stay over 50% charged
for up to one year in a cool
storage location, but your
smartphone will NOT receive
BLE battery notifications.
Temperature and other
environmental conditions
affect how long the EcoJump
will stay charged while in
storage. If you choose to
not use the EcoJump App
to receive BLE battery
notifications, we recommend
that you check your EcoJump
charge status every 3 months
and re-charge it as needed.

16 17
Unit Weight
27.3 ounces
Jump Start Output Power
600A Peak
Power Source
11.1V, 5000mAh, 55.5Wh
Lithium Battery
USB Input
5V, 2A
USB Output
5V, 2.1A / 5V, 2.1A
Bluetooth Low Energy (BLE)
Communicates the battery
level and temperature to
your smartphone
LED Flashlight
200 Lumens
Unit Dimensions
8"
4.1"
1.8"
Specifications
Mount Attachment Point
¼" diameter
Charging Options
USB to 5V AC adapter
or Computer
Charging Time
Approximately 7 hours
Recommended Max Storage
(Battery) Temperature
77°F / 25°C
Recommended Min Storage
(Battery) Temperature
-4°F / -20°C
Operating Temperature
32°F to 113°F / 0°C to 45°C
Waterproof/Dustproof Rating
IP67
!
JUMP START INSTRUCTIONS:
1. RED Clamp to (+) Terminal
2. BLACK Clamp to (-) Terminal
3. Insert Jump Start Cable
4.Press Power Button
5. Check Status Lights
READY TO JUMP
DISCONNECT!
RECHARGE ECOJUMP
STATUS
POWER
PRESS:
FLASHLIGHT
HOLD:
HAZARD OVERRIDE
PUSH TO SEAL
Mount Attachment Point Flashlight
For Charging (Sold Separately)
USB Car Power Adapter (2A)
User Guide
Optional Accessories
What’s in the Box
EcoJump
Models: GDI-EXJMP1500...1520
User Guide
EcoJump
USB Cable
Carry Bag
AC Power Adapter
Jump Start Cables

18
LIMITED MANUFACTURER’S WARRANTY:
The EcoJump is covered by a 3 year limited warranty that covers defects in workmanship
and / or materials for a period of 3 years from original purchase date. This warranty does
not apply to any products which have been abused, neglected, modified or used for a
purpose other than the one for which they were manufactured. Please refer to the above
care and maintenance instructions for suggested care details. The warranty is valid only
for the original owner who purchases the unit from an authorized dealer. Transfers do not
qualify for warranty protection. Grace Digital reserves the right to replace any out-of-
stock or discontinued product with a comparable product. Discontinued products may
not be available for warranty replacement. Any contents are NOT covered by the limited
manufacturer’s warranty. Warranty terms may be revised without notification at the
discretion of the manufacturer. Please visit www.ecoxgear.com for additional product &
warranty information.
EcoJump by ECOXGEAR, a division of Grace Digital Inc., San Diego, California.
Designed and Engineered in the USA. Made in China.
Patent Pending.
Ambient Storage Temperature Range
-4°F to 77°F
Jump Start Output Power
Peak Current
12Vdc, 600A (continuous 0.3S,
interrupted 15S)
Start Current
12Vdc, 200A (continuous 3S,
interrupted 15S)