Edge Wireless BTR-12 User manual

7TH BUILDING, NO.59 CHUANG FU ROAD,XIAO GANG
INDUSTRIAL ZONE, NINGBO 315800, CHINA
Tel [phone]Fax [phone]www.edgeholdings.com
Bluetooth®Audio Receiver BTR-12
Design Features And Functions
Rear Flush Mount Instructions
Note
Important
Drilla 1 1/8" (30mm) diameter hole.
There are two grommets remove one and leave one in place.
Feed the wires and the threaded protion throuth the hole,place on the second grommet and screw the
nut back into place until tightly installed
The orientation of the unit can be adjusted in either of the mounting positions simply by loosening the unit
at the back and rotating the device.
Never attempt to open, repair, or modify any part of the unit doing So will void all warranty.
You should open, remove the fuse, and leave the cap open on the fuse holder to feed it through the
hole.
Check local laws regarding the use of a mobile phone and a handsfree kit while
driving. If you use the Bluetooth® unit while driving, ensure your attention and focus remains on your
responsibility of driving safely.
Turning Unit - ON / OFF
Connect Yellow Wire (B+) 12V Battery and Black Wire (B-) 12V Ground securely,
Press button and hold it for over 3 seconds until you see the blue LED light goes out (OFF) or stays lit for
(ON).
Previous
Play/Pause
Next
Blue LED Blinking - Pairing Mode
Blue LED Solid - Paired
VOL -
Power on/o
VOL +
Red -(B+)- 12V Ignition/Accessory Power
Black -(B-) 12V Ground
Blue/White Stripe - Amplifier Remote Turn on
Yellow - (B+) - 12V Battery/Constant/Fused Power
AUX Audio Input - Red 3.5mm Connector
RCA Audio Output(to Amp)

Function Guide ( BTR-12)
Instruction
Tap
Press and Hold
Duration
Press once briefly
Press the button and hold it for 3 seconds
Pairing Bluetooth" Device
Go to settings on your phone and place Bluetoothsetting into "discoverable " mode.
Search for (BTR-12) device.
On phone select (BTR-12) to pair device.
Once a device is paired each time this device is seen by the BTR-12 it will automatically reconnect to the
device. If no device is present the BTR-12 automatically goes intopairing mode and will present itself as
discoverable for the next device present.
Ignition / Accessory / Remote Amp Trigger
Connect the Red to the lgnition/Accessory wire from the head unit ar other Power ON/OFF switching.
When BTR-12 is used in this method the ON/OFF switching built into the device is by-passed and will not
function. Unit will be turned ON/OFF via the head unit ar other controller.
Connect the Blue/White Stripe (Remate out trigger) to the amplifier remote trigger to turn the amplifter
ON/OFF via the BTR-12. When you press PAK button and hold it for longer than 3 seconds the BTR-12 will
turn ON or OFF and will also turn the amplifier ON or OFF.
AUX Input/ Output
Connect AUX Input with any media player.
Connect RCA output to amplifier .
Double tap button rapidly to switch between Bluetooth®source and AUX input source.
When using the AUX Input source the volume control in the BTR-12 is by-passed and you wlll use the
volume control on the alternate source.
When in AUX mode the AUX button will illuminate.
Troudle Shooting Guide
Make sure volume is up on bluetooth sources.
Confirm Pairing if no sound.
Power ON/OFF will only work when the Yellow Power Wire is connected. If you connect theRed Power
Wire it by-passes the Power ON/OFF function. If you want to manua lly turn the power ON/OFF you need
to only connect the Yellow Power Wi re.
If you want the device to power up and power down automatically (and by-pass theON/OFF switching)
you will need to connect the Red Power Wire to the ignition or to a switched power source.
7TH BUILDING, NO.59 CHUANG FU ROAD,XIAO GANG
INDUSTRIAL ZONE, NINGBO 315800, CHINA
Tel [phone]Fax [phone]www.edgeholdings.com
Bluetooth®Audio Receiver BTR-12
Gromment
Gromment
Nut