EDIFIER T5 User manual

T5
Powered Subwoofer
User manual | Manuel d’utilisateur |Manual de usuario | Bedienungsanleitung |Manuale dell’utente | Manual do utilizador

1
English
Important safety instruction
Excessively loud music may lead to hearing loss. Please keep the volume in a safe range.
Correct Disposal of this product. This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased. They can take this product for
environmental safe recycling.
Use only with the cart,stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
1. Please read the instructions carefully. Keep it in safe place for future reference.
2. Use only accessories approved by the manufacturer.
3. Install the instrument properly by following the instructions in the device connection section.
4. Using the product in a 0-35ºC environment is recommended.
5. To reduce the risk of fire and electric shock, do not expose the product to rain or moisture.
6. Do not use this product near water.Do not immerge the product into any liquid or have it exposed to dripping or splashing.
7. Do not install or use this product near any heat source (e.g. radiator,heater,stove,or other devices that generate heat).
8. Do not place any object filled with liquids,such as vases on the product;neither should any open fire,such as lighted candles
be placed on the product.
9. Do not block any ventilation openings.Do not insert any object into ventilation openings or slots. It may cause fire or electric
shock.
10. Keep sufficient clearance around the product to maintain good ventilation (minimum 5cm is recommended).
11. Do not force a plug into the jack.Before connection, check for blockage in the jack and whether the plug matches the jack and
is oriented to the right direction.
12. Keep the provided accessories and parts (such as screws) away from children to prevent from being swallowed by mistake.
13. Do not open or remove the housing yourself. It may expose you to dangerous voltage or other hazardous risks. Regardless
the cause of damage (such as damaged wire or plug, exposure to liquid splash or foreign object falling in,exposure to rain or
moisture,product not working or being dropped, etc.),the repair has to be performed by an authorized service professional
immediately.
14. Before cleaning the product with dry cloth, always turn off the product and disconnect the power plug first.
15. Never use strong acid, alkali, gasoline, alcohol, or other chemical solvents to clean the product surface. Use only neutral
solvent or clear water for cleaning.

2
English
Important safety instruction
This symbol is to alert the user to the presence of un-insulated dangerous voltage within the product's enclosure
that may be ofsufficient magnitude to constitute a risk ofelectric shock to persons.
This symbol is to warn the user not to disassemble the enclosure of the product and there is no user-replaceable
part inside. Take the product to an authorized service center for repair.
This symbol indicates that the product is for indoor use only.
This symbol indicates that the product is a CLASS II or double insulated electrical device with no earth requirement.
Power warning:
1. Place the product near the power outlet for easy use.
2. Before use, make sure that the operating voltage is the same as your local power supply. Correct operating voltage can
be found on the product plate.
3. For safety purpose, unplug the product during lightning storms or when unused for extended periods of time.
4. Under normal conditions,the power supply may get hot.Please keep good ventilation in the area and exercise caution.
5. Safety warning labels on the housing or bottom ofthe product or power adaptor.
The MAINS plug is used as the disconnect device,the disconnect device shall remain readily operable.

3
English
Unpack the box
Box Contents
User manual
RCA to RCA audio cable
3.5mm - RCA audio cable
Power cable
Subwoofer

4
English
Illustration
1. Power indicator
Power on:green
Standby:red (unit will enter standby mode following 5 minutes sans signal)
2. Power switch
3. Power cable connector
4. Volume adjustment
5. Low frequency bandwidth
6. Phase selection
7. Signal input
8. Signal output
①
②
③ ④ ⑤ ⑥ ⑦ ⑧

5
English
Operational Guide
Note:
1. Be sure to unplug the power cables of subwoofer and audio source device from the wall outlet prior to any
connections.
2. This product is a powered subwoofer that can be connected to audio source devices with low levels or pre-stage
signal output (such as powered amplifier, DVD, Blu-ray player, TV, PC,mobile phone, Pad, set top box,TVbox
and game console etc.), but CANNOT BE CONNECTED to rear power output terminal ofpowered amplifier device.
Audio source device
Connection 1
Connection 2
SUB OUT
LINE OUT
R
L

6
English
Operational Guide
Connections:
Connection 1:
“Subwoofer Output” connection:
If audio source device has the port like “Sub Out”, “Woofer Out”, “SW Out” or “LFE Out”,namely the line output port
specialized for connecting subwoofer,please connect this output port to “Signal In” port on the subwoofer using
audio cable.
Connection 2:
“Left and Right Sound Channel Output” connection:
If audio source device has no dedicated subwoofer output port but has left and right sound channel line output
port (LINE OUT) (or FL/FRoutput port on the devices supporting 5.1/7.1 channels),please connect this left and right
sound channel line’s output port to “Signal In” port on the subwoofer using audio cable, then connect “Signal Out”
port on the subwoofer to audio input port on the powered main speaker.
Volume Adjustment:
To achieve optimum listening effect, ensure the subwoofer’s volume is reasonably matched with that ofthe main speaker.
Please set the subwoofer’s volume to the minimum level prior to adjustment.
If connected by connection 1:
1) Set Bass Adjustment ofaudio source device to the “middle” or “0 dB” position (if have).
2) Play audio source containing low frequency components and adjust the main speaker’s volume to an appropriate
level &
3) Gradually increase the subwoofer’s volume until it can be matched with that ofthe main speaker;
After adjustment is finished,adjusting the audio source device’s master volume can control the subwoofer and other
speaker’s volume simultaneously.

Operational Guide
If connected by connection 2:
1) On the audio source device play audio source containing low frequency components and adjust the audio source’s
volume to 50%level;
2) Adjust the main speaker’s volume to an appropriate level; &
3) Gradually increase the subwoofer’s volume until it can be matched with that ofthe main speaker;
After the adjustment is finished, adjusting the audio source device’s master volume can control the subwoofer and other
speaker’s volume simultaneously.
Low FrequencyBandwidth Adjustment:
This adjustment determines the crossover point inputting to the subwoofer. Bass signal below the crossover point will
be “handed over” to the subwoofer for playing. Ifaudio source device can set the crossover point, please rotate the
“low frequency bandwidth” knob on the subwoofer to the rightmost,and the crossover point is determined by the audio
source device;Ifaudio source device cannot set the crossover point,please adjust the “low frequency bandwidth” knob
to select an appropriate crossover point.
Generally,ifthe main speaker connected to the subwoofer is a larger speaker (such as above 4 inches), setting the
crossover point to 50-90Hz is more reasonable; if the main speaker is a smaller one (such as below 4inches),setting
the crossover point to 90-150Hz is more appropriate.The smaller the speaker,the higher the crossover frequency
should be.
After the entire audio system is connected properly, please adjust the low frequency bandwidth and the subwoofer’s
volume until the subwoofer and other speaker achieve smooth bass combination.
Phase selection:
Acoustically match the subwoofer’s output with that of the main speaker. Please select the “0” or “180” degree phase
and observe which phase can obtain much subwoofer output at the listening position.
7
English

8
English
Specifications / Troubleshooting
Power output:70W
Frequency response:38Hz-200Hz
There is no restriction of use.
Troubleshooting
To learn more about EDIFIER, please visit www.edifier.com
For Edifier warranty queries, please visit the relevant country page on www.edifier.com and review the section titled
Warranty Terms.
USA and Canada: [email protected]a
South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact
information.
No sound
1. Ensure audio source is playing and all cables are firmly connected.
2. Ensure signal output of audio source is set correctly.
3. Check the volume levels on speakers and audio source player.
4. Please turn speakers off and restart them.
Noise comingfrom speakers
Edifier speakers generate little noise, while the background noise of some audio devices are too high. Please unplug
audio cables and turn the volume up, if no sound can be heard at 1meter away from the speaker, then there is no
problem with this product.

Manual Edition 1.1,May 2019
IB-200-T00050-02
NOTICE:
For the need oftechnical improvement and system upgrade, information contained herein may be subject to change from
time to time without prior notice.
Products ofEDIFIERwill be customized for different applications. Pictures and illustrations shown on this manual may be
slightly different from actual product. Picture for reference only,actual product prevails.
Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong
Tel: [phone]
Fax: [phone]
www.edifier.com
© 2019Edifier International Limited. All rights reserved.
Printed in China