EGO 360 i7w User manual

Quick Set-up Guide
EGO-360 i7w Speaker with
MicroSD Card *Read/Write
360º Omni-Directional Sound
Please read your manual carefully to familarise yourself with your EGO-360 i7w prior to
setup & initial operation.
How to charge your EGO-360 i7w speaker
Before using your EGO-360 i7w speaker
PRECAUTIONS
1. Care should be taken to avoid placing your EGO-360 i7w in the following locations:
(a) Near heat sources or direct sunlight
(b) Wet or humid locations
2. EGO-360 i7w is not waterproof. Do not allow water to enter your EGO-360 i7w.
Caring for your EGO-360 i7w
3. To clean the black Viscous Gel-Pad, use a clean, lint-free damp cloth to remove excessive
build up of dirt or dust.
4. Only place your EGO-360 i7w Vibration Speaker on flat surfaces.
5. Only use our dedicated glass Suction Cup (accessory) for vertical windows/glass & utilise the
Gel-Pad Protection Disc (9). Apply slight moisture to suction-cup surface & engage the
‘Swivel-Lock’.
6. Our Hard-Surface Mount (accessory) is for materials of non-glass both vertical & above.
Handy Tips
7. For best result, select surfaces that resonate well (i.e. pine, melamine, polystyrene, cardboard,
plastic, domestic glass).
8. Your EGO-360 i7w will not work well on concrete, laminated glass, stone bench tops, or other
thick/solid objects or extremely soft objects like material or skin.
WARNING
Never use with a damaged or defective power supply cord.
To reduce the risk of electric shock, do not attempt to open the casing of your EGO-360 i7w speaker.
Please visit our website for a full instruction manual,
accessories, spare parts, FAQ’s, support & more:
www.ego-360.com Designed in Australia & Manufactured in China
ROHS
CONGRATULATIONS
on the purchase of your EGO-360 i7w Intelligent Speaker!
1. Remove the white plastic Gel-Pad Protection Disc (9) to expose the black Viscous Gel-Pad (8)
before use.
2. Your EGO-360 i7w speaker will work on any flat, clean, solid and smooth surface e.g. table
(glass or wood), cardboard, plastic, window (with optional glass suction cup).
3. Lightly press the top of your EGO-360 i7w to create a good connection between the
Gel-Pad and the surface used.
Note:
Please ensure to remove the MicroSD card when charging from a non-Plug & Play device
(i.e. AC USB charger, car USB charger etc.)
1. Insert the Mini-USB Connector from the Data/Charge Cable (11) into the Mini-USB Port (5)
located on the side of your EGO-360 i7w.
2. Plug the Type A USB connector on the other end into an external USB power source (i.e. phone
charger, PC/Laptop, car charger).
3. The LED Indicator Light (2) will glow red when charging from a power source and turn bright
green when fully charged.
Charge Time = 1-2 hours Playback Time = 8-10 hours (playback time may vary as to volume level used)

10
11
9
GETTING TO KNOW PLAYING MUSIC
your EGO-360 i7w Vibration Speaker
3 Individual Ways
Visit ego-360.com for accessories & spare parts360º Omni-Directional Sound Visit ego-360.com for support, store locations & more
1. All Aluminium ‘Uni-Body’ Design
2. LED Indicator Light
3. Toggle/Wheel Control
4. 3-Way On/Off/MicroSD Switch
5. Mini-USB Port
6. MicroSD Slot
7. Speaker Foot with screw thread
8. Viscous Gel-Pad
9. Gel-Pad Protection Disc
10. Audio Cable
11. Data/Charge Cable
How to use Cable Connection (Audio 3.5mm Jack)
1. Connect the Mini USB Cable to your EGO-360 i7w, then connect
the 3.5mm Audio Cable (10) (headphone jack) to the external sound
source e.g. MP3, Laptop, PC, Mobile Phone etc.
2. Turn the 3-Way Switch (4) to ‘Speaker’ position (the LED Indicator Light (2)
will glow green after 3 seconds) to listen to your music and control your
music from the external sound source.
How to use your EGO-360 i7w as a Plug & Play Speaker
1. Insert the Mini-USB Connector (11) into the Mini-USB port located on
the side of your EGO-360 i7w.
2. Plug the Type A USB (11) into a Plug & Play compatible PC/Laptop/Mac
3. Ensure the 3-Way Switch (4) located on the side of your EGO-360 i7w is
in the central off position.
4. The LED Indicator Light (2) will glow red and turn green depending
on battery level/charge.
5. Open your music file e.g. iTunes, Windows Media, select a track/
playlist and press play.
How to use the MicroSD card (TF)
1. Insert the Memory Card MicroSD in the MicroSD Slot (6) of your EGO-360 i7w (1) and turn the
switch to ‘MicroSD’.
2. The LED Indicator Light (2) will turn green after 3 seconds, this will indicate your EGO-360 i7w is
actively playing the inserted MicroSD card (accessory) audio files.
3. With the Toggle/Wheel Control (3), slide and hold the control V+ / V- for volume up/down.
4. A quick flick of the Toggle/Wheel Control (3) to next/or previous music tracks.
Press button briefly for Pause/Play function.
& Read/Write files to your MicroSD card
1. First you will need to add audio files to your MicroSD card via the Data/Charge Cable (11). Ensure the
3-Way Switch (4) is in the central off position.
2. Insert your MicroSD card into the MicroSD Slot (6) located on the side of your EGO-360 i7w.
3. Plug the Type A USB Connector on the Data/Charge Cable (11) into the USB port of your Windows/Mac
compatible computer.
4. Your MicroSD card will show up on your Windows/Mac compatible computer as an external
mapped drive.
5. Simply drop and drag your .mp3, .m4a (iTunes), .WMA and .WAV audio files onto your MicroSD
mapped drive.
6. Select MicroSD by sliding the 3-Way Switch (4) located on the side of your EGO-360 i7w to the
right. The LED Indicator Light (2) will turn green after 3 seconds. This indicates your EGO-360 i7w is
actively playing the inserted MicroSD card.
Note:
Default volume is set at 45% please use the Toggle/Wheel Control (3) to
adjust master volume up or down, slide and hold the control V+ / V-
& press button briefly for mute/on/off function.
Note:
Your EGO-360 i7w ‘Intelligent Edition’ can act as a portable storage device,
because many files can be copied to MicroSD card (up to 256GB capacity)
& those files can be shared with other computer via the data cable connection.
1
2
34
5
6
7
8