EINHELL ERGO TOOLS E-AS 18-evo User manual

E-AS 18-evo
Operating Instructions
Battery-powered Drill/Screwdriver
with Adjustable Torque
Art.-No.: 44.720.83 I.-No.: 01016

Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 1


Important: Read and note the operating
instructions and safety regulations before
using!
2
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 2

3








Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 3

1. Layout:
1: Torque adjustment facility
2: Bit holder
3: Forward / Reverse selector switch
4: On/Off switch
5: Battery pack
6: Battery charger
7: Selector switch for 1st/2nd gear
8: Pushlock button
2. Safety information
Please refer to the booklet included in delivery for
the safety instructions.
3. Important information
Be sure to read the following information before you
use your cordless screwdriver for the first time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 1 hour.
2. Only ever use sharp drill bits and screwdriver bits
which are suitable for the purpose intended.
3. Always check for concealed electric cables, gas
and water pipes BEFORE drilling and screwing
into walls.
4. Starting up
Charging the NC battery pack
1. Take the rechargeable battery pack out of the
handle, pressing the pushlock buttons at the side
to do so.
2. Check that your mains voltage is the same as that
marked on the rating plate of the battery charger.
Plug the battery charger in the socket.
3. The green LED will come on. Insert the battery
pack in the battery charger. Now the red LED will
come on to indicate that the battery pack is being
charged. When the charging period is completed
after approx. 1 hour, the green LED will come on
again. The temperature of the battery pack may
rise during the charging operation. This is normal.
If the battery pack fails to become charged, please
check
앬whether there is voltage at the socket-outlet
앬whether there is proper contact at the charging
contacts on the charger.
If the battery still fails to become charged, please
return
앬the charger
앬the battery pack
to our Customer Service Department.
Timely recharging of the Ni-Cd battery pack is
recommended in the interest of long battery life.
Recharging is always necessary when you notice
that the power of the battery-powered
drill/screwdriver is decreasing.
Never allow the battery pack to discharge
completely. This will result in damage to the Ni-Cd
battery pack!
Adjusting the torque (1)
The battery-powered drill/screwdriver is equipped
with a 16-step mechanical torque adjustment facility.
The torque for a specific size of screw is selected
with the set-collar (Figure 1). The correct torque
depends on several factors:
앬on the type and hardness of material in question
앬on the type and length screws used
앬on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
Drilling
For drilling purposes, move the set-collar to the last
step „Drill“ (Figure 1). In this setting the slip clutch is
inactive. The maximum torque is available in drilling
mode.
Forward/Reverse switch (3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against being
switched on accidentally. You can choose between
clockwise and anticlockwise rotation. To avoid
causing damage to the gearing it is advisable to
change the direction of rotation only when the tool is
4
GB
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 4

at a standstill. The On/Off switch is blocked when
the slide switch is in centre position.
On/Off switch (4)
Infinitely variable speed control is possible with the
On/Off switch. The further you press the switch, the
higher the speed of the battery-powered
drill/screwdriver.
Changing over from 1st gear to 2nd
gear (7)
You can work at a higher or lower speed depending
on the position of the selector switch. To avoid
damaging the gear unit you should only change over
gears when the tool has stopped.
Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described elsewhere in these operating instructions,
to suit the size of screw.
Technical data
Voltage supply 18 V =
Speed 0-350/0-900 rpm
Torque 16 levels
Forward and reverse rotation yes
Chuck clamping width 1 - 10 mm
Battery charging voltage 18 V =
Battery charging current 2.5 A
Mains voltage for charger 230 V ~ 50 Hz
Sound pressure level LPA: 69 dB(A)
Sound power level LWA: 80 dB(A)
Vibration a
– w< 2.5 m/s2
Weight 1.75 kg
Ordering replacement parts
Please quote the following data when ordering
replacement parts:
앬Type of machine
앬Article number of the machine
앬Identification number of the machine
앬Replacement part number of the part required
5
GB
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 5

6
Landau/Isar, den 28.03.2006
Vogelmann
Product-Management
Akkuschrauber E-AS 18-evo
Weichselgartner
Leiter QS Konzern
ISC GmbH
Eschenstraße 6
D-94405 Landau/Isar Konformitätserklärung
Art.-Nr.: 44.720.83 I.-Nr.: 01016 Archivierung: 4472080-14-4155050
Subject to change without notice
EN 60745-1; EN 60745-2-1; EN 60745-2-2; EN 60335-1; EN 60335-2-29;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
98/37/EG
73/23/EWG_93/68/EEC
97/23/EG
89/336/EWG_93/68/EEC
90/396/EWG
89/686/EWG
87/404/EWG
R&TTED 1999/5/EG
2000/14/EG:
95/54/EG:
97/68/EG:
x
x
x
Derklärt folgende Konformität gemäß EU-Richtlinie
und Normen für Artikel
declares conformity with the EU Directive
and standards marked below for the article
Fdéclare la conformité suivante selon la
directive CE et les normes concernant l’article
verklaart de volgende conformiteit in overeen-
stemming met de EU-richtlijn en normen voor
het artikel
Edeclara la siguiente conformidad a tenor de la
directiva y normas de la UE para el artículo
Pdeclara a seguinte conformidade de acordo
com a directiva CE e normas para o artigo
Sförklarar följande överensstämmelse enl. EU-
direktiv och standarder för artikeln
ilmoittaa seuraavaa Euroopan unionin direkti-
ivien ja normien mukaista yhdenmukaisuutta
tuotteelle
erklærer herved følgende samsvar med EU-
direktiv og standarder for artikkel
заявляет о соответствии товара
следующим директивам и нормам EC
izjavljuje sljedeću uskladjenost s odredbama i
normama EU za artikl.
declarå urmåtoarea conformitate cu linia direc-
toare CE μi normele valabile pentru articolul.
ürün ile ilgili olarak AB Yönetmelikleri ve
Normlar∂ gere©ince aμa©∂daki uygunluk aç∂kla
mas∂n∂ sunar.
‰ËÏÒÓÂÈ ÙËÓ ·ÎfiÏÔ˘ıË Û˘Ìʈӛ· Û‡Ìʈӷ ÌÂ
ÙËÓ √‰ËÁ›· ∂∂ Î·È Ù· ÚfiÙ˘Ô ÁÈ· ÙÔ ÚÔ˚fiÓ
Idichiara la seguente conformità secondo la
direttiva UE e le norme per l’articolo
attesterer følgende overensstemmelse i
henhold til EU-direktiv og standarder for
produkt
prohlašuje následující shodu podle směrnice
EU a norem pro výrobek.
Ha következő konformitást jelenti ki a termékek-
re vonatkozó EU-irányvonalak és normák
szerint
pojasnjuje sledečo skladnost po smernici EU
in normah za artikel.
deklaruje zgodność wymienionego poniżej
artykułu z następującymi normami na
podstawie dyrektywy WE.
vydáva nasledujúce prehlásenie o zhode podľa
smernice EÚ a noriem pre výrobok.
деклаpиpа следното съответствие съгласно
диpективите и ноpмите на ЕС за пpодукта.
заявляє про відповідність згідно з Директивою
ЄС та стандартами, чинними для даного товару
deklareerib vastavuse järgnevatele EL direktiivi
dele ja normidele
deklaruoja atitikti pagal ES direktyvas ir normas
straipsniui
izjavljuje sledeçi konformitet u skladu s odred
bom EZ i normama za artikl
Atbilstības sertifikāts apliecina zemāk minēto preču
atbilstību ES direktīvām un standartiem
EE
SCG
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 6

7
 Technical changes subject to change
 WARRANTY CERTIFICATE
The product described in these instructions comes with a 2 year warranty
covering defects. This 2-year warranty period begins with the passing of risk or
when the customer receives the product.
For warranty claims to be accepted, the product has to receive the correct
maintenance and be put to the proper use as described in the operating
instructions.
Your statutory rights of warranty are naturally unaffected during these 2
years.
This warranty applies in Germany, or in the respective country of the
manufacturer’s main regional sales partner, as a supplement to local
regulations. Please note the details for contacting the customer service center
responsible for your region or the service address listed below.
Einhell UK Ltd
Unit 5 Morpeth Wharf
Twelve Quays
Birkenhead, Wirral
CH 41 1NG
Tel. [phone], Fax [phone]
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 7

For EU countries only
Never place any electric tools in your household refuse.
To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its
implementation in national laws, old electric tools have to be separated from other waste and disposed of
in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the demand to return electrical devices:
As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the
device is properly recycled if ownership is relinquished. This can also be done by handing over the used
device to a returns center, which will dispose of it in accordance with national commercial and industrial
waste management legislation. This does not apply to the accessories and auxiliary equipment without
any electrical components which are included with the used device.

The reprinting or reproduction by any other means, in whole or in part,
of documentation and papers accompanying products is permitted only
with the express consent of ISC GmbH.
EH 04/2006
Anleitung E-As 18 evo SPK7 03.04.2006 6:39 Uhr Seite 8