Eizo ET Arm Series User manual

Dimensions and color of the product are subjec to change.
Please, read this manual before using this product.
Please, put the manual at the place within your sight after reading the manual.
The guarantee is included at the back side.
Please, definitely observe the items with the following
instructions because they are for preventing unexpected
danger or losses in advance by using the product safely and
accurately.
※ In case a user fails to keep warnings for safety, our after-sale service is not available.
Please, use the product properly according to the
contents of the manual.
Cautions

4mm (1pcs)

4 x12mm (4pcs)
4 x16mm (4pcs)




(4pcs)
  2pcs)
Please, be sure to follow the contents of this
manual.
if not , it may be the cause of injuries or breakdowns.
In case screw-loosening or looseness come
upon arm while using, tighten the screw again.
If used in a state where screws are loose, it could be a
cause of injuries or breakdowns by the fall of the
monitor.
Don't disassemble or make over arm. 
At a time when repairs are needed, please contact
EIZO SUPPORT.
Don't give any strength or impact to the
product after installing it.
It could cause the damage to the product and impair
its smooth running. 
Install the product at a stable wallside which
can stand up under the weight of the product
and monitor.
Please, be cautious because there is a risk of being
damaged.
Don't cling to or lean on the arm or monitor.
It could be the cause of injuries or breakdowns by the
fall of the monitor.
Be careful not to drop the product. 
There could be a problem in its motion, so be careful.
Please, definitely use the designated bolts and
tools when installing the product.  
In case of using the undesignated bolts or tools, there
might be a fear of a failure in the product or safety
problems.
Please, be careful not to give a shock to the
product when moving it.

※ In case a user fails to keep warnings for safety, our after-sale service is not available.
Please, use the product properly according to the
contents of the manual.
Cautions
Product Manual Product Composition & Specications
Cautions for Safety Cautions for Safety

Modulating Method consequent
on the weight of the monitor
After attaching a drawing
to the spot where the
product is installed, please
mark the four spots of
anchor bolts.
Using the drill bit of 6-mm
diameter at the spot marked
on the wall where anchor
bolts are, drill a hole within
the length of 55 mm.
Please, detach the attached
drawing, and clean the
drilled hole.
After inserting the anchor
bolts for xing into four
spots t in with the hole as
specied in the picuture,
please press the product to
the hole which is inserted
by the anchor bolts for
xing.
Please tighten the xing bolts
to the hole using a philips
screwdriver. The installation
job is nished with the
tightening the xing bolts at
four spots so that the bolts can
be completely pressed to the
wall.
Fixing Bracket on the wall
after complete
At the time of installing the product, rst , conrm
whether the wall materials meet the condition after
denitely
Don't install this product at glass, thin wood or the
wall thinner than 60mm.
Cautions
The xing bolts to the
monitor have two sizes ; one
is 4x12mm, and the other is
4x16mm. Use the size to the
monitor.
Putting the monitor at the bottom with its
back side up and tighten the xing bolts to
the VESA hole like the <Fig. 1>. Completely
tighten the four pieces of xing bolts.
Insert the ARM HINGE into the gap of the
xing bracket on the wall . At the time of
inserting it, be careful about the
direction of ARM HINGE.
With the tightening of the knob bolts
to the hole like the <Fig>, the
installaton job is done.
The span between holes for installing this product is 100x100, or 75x 75mm
based on the size standard. Completely tighten the VESA Assembly of the
monitor using 4 xing bolts to the size 100x100 or 75x75 for the assembly
job.
This product is applicable to the monitor with the weight from
3kg to the maximum 7kg.

4mm


You can use 4-mm-wrench for
modulation as showing in <Fig. 1>
by modulating "+" or "
- " like
<Fig.2>.
When changing the monitor from
19 inches to 22 inches, you can
modulate it like the drawing beside.
You can use it in accord with the
weight of the monitor.
Method of Installing the product Method of Assembling a Monitor
Guarantee & After-sale Service

壁面固定用図面
The wall for attachment drawing
壁面固定ブラケットの設置の前、ネジ穴を正確な位置に合わせなければなりません
ので、 設置する場所にこの図面を貼り付けて下さい。貼り付けた後、図面の4箇所
の黒い円型に穴を開けてください。
Attach exact location you want before installing the xing bracket wall.
Drill holes in the four black circle after completed.