Sim-Lab FREESTANDING VARIO SINGLE User manual

FREESTANDING VARIO™ MONITOR MOUNT
SINGLE/TRIPLE
VERSION 2.0
Last updated: 11-09-2023
INSTRUCTION MANUAL

2|2 15
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 14) and make sure all the parts are delivered.
We have combined the assembly instructions for the single and triple versions of this product into one
manual. If you have purchased the triple version and build from scratch, you can skip some pages which
involve assembly and installation of the Vario VESA mounts and do those last.
This product furthermore combines products we normally offer separately. We encourage you to read the
product manuals for included products if this one doesn’t answer all of your questions. Please refer to the
following if needed:
www.sim-lab.eu/xero-play-pivots-manual
www.sim-lab.eu/vario-vesa-manual
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
5/6MM

3|3 15
76MM
or
3”
25MM
or
1”
BUILD 2X
M8 X 20
2X
Slot-Nut M8
4X
A4
1X
Profile 40X40
End-Cap
2X
Rubber
Foot
2X
A4
A5
A15
A10
A13

4|4 15
Instructions for the right side (A3)
are similar. See page 7 for the
orientation of the profile.
BUILD 2X
Profile 80X40
End-Cap
1X
M8 X 16
2X
Slot-Nut M8
4X
A2
(LEFT)
1X
Corner
Bracket
2X
Washer M8
2X
A2
A9
A15
A7
A14
A12

5|5 15
BUILD 2X
M8 X 16
2X
Washer M8
2X
A14
A12

6|6 15
Profile 80X40
End-Cap
2X
Slot-Nut M8
8X
A1
1X
M8 X 20
8X
Sandwhich
Plate 80
2X
Washer M8
6X
A6
A1
A9
A15
A11
A14

7|7 15
M8 X 20
4X
Washer M8
4X
A3
A11 A14

8|8 15
If you purchased the
‘Triple Upgrade’, please
continue on page 10.
M8 X 16
2X
Washer M8
2X
Vario VESA
Holder
1X 4X
Corner Bracket
Cap
Slot-Nut M8
2X
A8
D1
D12
D8
D11

9|9 15
When parts D9 and D10 are installed like above,
monitors are easy to install in a neutral
position. Parts D9 can be adjusted to change
the tilt and/or height.
Parts D10 can be adjusted to adjust the monitor
sideways if needed, and fix it in place.
Vario VESA
Plate
1X
Vario VESA
Pin Holder
2X
M8 X 40
(Set Screw)
2X
M5 X 20
(Set Screw)
2X
M5 X 20
4X
Vario VESA
Pin
1X
D3
D2
D9
D5
D10
D10
D9
D4

10 |10 15
M8 X 25
8X
Slot-Nut M8
8X
Pivot
Adapter
4X
C5
C5
C5
C1
C5
C3

11 |11 15
Instructions for the right side (B2)
are similar. See the next page for
the orientation of the profile.
* Mind the orientation of the Slot-Nuts.
BUILD 2X
Profile 80X40
End-Cap
2X
M8 X 25
4X
Slot-Nut M8
4X
B1
(LEFT)
1X
Pivot
Adapter
2X
C5
C5
C5
C1
C5
C3
C5
B3
B1

12 |12 15
Adjust arm angles to your preference.
We included markings in the pivots.
Markings are placed in 10° increments.
120°
M8 X 40
4X
Nut M8
4X
C4
C2

13 |13 15
M8 X 16
4X
Washer M8
4X
Vario VESA
Holder
2X
Slot-Nut M8
4X
D1
D12
D8
D11

14 |14 15
BOX A - VARIO SINGLE MONITOR MOUNT
PROFILE KIT
#Part QTY Note
A1 80X40 Length=1195mm 1
A2 80X40 3N Length=1195mm 1 Left upright, engraved.
A3 80X40 3N Length=1195mm 1 Right upright, engraved.
A4 40X40 Length=580mm 2
HARDWARE KIT
A5 Rubber foot 4
A6 Triple sandwich plate 80 2
A7 Corner bracket 40x40 4
A8 Corner bracket 40x40 cap 4
A9 Profile 80x40 end-cap 4
A10 Profile 40x40 end-cap 4
A11 Bolt M8 X 20 DIN 912 8
A12 Bolt M8 X 16 DIN 912 8
A13 Bolt M8 X 20 DIN 7380 4 Buttonhead.
A14 Washer M8 DIN 125-A 8
A15 Slot-Nut M8 24
BOX B - TRIPLE MONITOR MOUNT
PROFILE KIT
#Part QTY Note
B1 80X40 3N Length=580mm 1 Left arm, engraved.
B2 80X40 3N Length=580mm 1 Right arm, engraved.
HARDWARE KIT
B3 Profile 80x40 end-cap 4
BOX C - Xero-Play triple pivot set
HARDWARE KIT
#Part QTY Note
C1 Xero-Play triple pivot adapter 8
C2 Bolt M8 X 40 DIN 912 4
C3 Bolt M8 X 25 DIN 912 16
C4 Nut M8 4
C5 Slot-Nut M8 16
BOX D - Vario VESA adapter set (x1 or x3 depending on purchase)
HARDWARE KIT
#Part QTY Note
D1 Vario VESA holder 1
D2 Vario VESA plate 1
D3 Vario VESA pin holder 2
D4 Vario VESA pin 1
D5 Bolt M5 X 20 DIN 7991 4
D6 Screw M4 X 16 DIN 7985 4 Philips head.
D7 Screw M4 X 10 DIN 7985 4 Philips head.
D8 Bolt M8 X 16 DIN 912 2
D9 Set screw M8 X 40 DIN 916 3
D10 Set screw M5 X 20 DIN 916 2
D11 Washer M8 DIN 125-A 2
D12 Slot-Nut M8 2
D13 Standoff M4 x 10 4
Disclaimer: for some entries on this page, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

15 |15 15
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: