ELAP HPS-M-05 User manual

INSTRUCTION MANUAL
SPECIFICATIONS
Stroke: 250 ÷ 8000 mm
Resistance 5 KOhm ±10%
Linearity ±0,25% (±0,3% for analogue output types)
Speed: 0.5/1 m/sec. (see the table)
Spring max torque: strokes ≤1250 mm = 600 g
Strokes from 1.5 to 4 m = 1000 g - Over: 2200 g
SUS304 stainless steel wire covered with nylon 0,6/1 mm –
max load 16/60 Kg. (see the table)
Operating temperature -20 ÷ 70°C (0 ÷ 70°C for analogue output
types) - Relative moisture 35%-90%
Connections: cable 1 m long (HPS-S 0.5 m)
Protection degree IP64 (HPS-S: IP50)
Type
Stroke
mm
Power
Speed
Wire Ø
/Max load
Type
Stroke
mm
Power
Speed
Wire Ø
/Max load
HPS-M-05
500
1W
1 m/sec
0.7 mm/ 23 Kg.
HPS-S-025
250
1W
0.5 m/sec
0.6 mm/ 16 Kg.
HPS-M-075
750
1W
1 m/sec
0.7 mm/ 23 Kg.
HPS-S-05
500
1W
0.5 m/sec
0.6 mm/ 16 Kg.
HPS-M-10
1000
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-S-10
1000
2W
0.5 m/sec
0.6 mm/ 16 Kg.
HPS-M-125
1250
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-L-30
3000
2W
0.6 m/sec
1 mm/ 60 Kg.
HPS-M-15
1500
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-L-40
4000
2W
0.6 m/sec
1 mm/ 60 Kg.
HPS-M-20
2000
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-L-50
5000
2W
0.6 m/sec
1 mm/ 60 Kg.
HPS-M-30
3000
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-L-60
6000
2W
0.6 m/sec
1 mm/ 60 Kg.
HPS-M-40
4000
2W
1 m/sec
0.7 mm/ 23 Kg.
HPS-L-80
8000
2W
0.6 m/sec
1 mm/ 60 Kg.
INSTALLATION
Make sure that the distance to be run by the wire does not exceed the transducer nominal stroke; stretching the wire over its
nominal stroke damages the transducer seriously, and causes the decay of the garantee right.
Use 4 M3 screws with the following specifications to fix the potentiometer: HPS-M screws M3x8 - HLS-S screws M3x6
–HLS-L screws M4x10
The wire must run out of the bushing without angle to obtain the best tolerance in measurements.
It is possible to hook the fixing end of the wire at a steady point and move the transducer body instead of the wire.
If the application is not a linear one, use a pulley with a proper diameter to smooth the rotation and avoid damaging the wire.
If the product works in a severe environment, such as in presence of oil, water, heavy dust, iron chipping or any powder which can
damage the wire, apply a protective cover.
CONNECTIONS
Carry out the connections as shown in the diagram hereunder. The cable shield is not connected inside the transducer.
HPS-M, HPS-S, HPS-L
HPS-M 10V, HPS-L 10V
HPS-M 420, HPS-L 420
The red and black
wires are connected
to the resistance
ends, while the
white wire is
connected to the
cursor
LINEAR WIRE
POTENTIOMETER
HPS-M ●HPS-S ●HPS-L
HPS

DIMENSIONS
Transducer HPS-M Dis.M2121
Transducer HPS-S Dis.M1302
Transducer HPS-L Dis.M1301
Further information at URL: https://www.elap.it/wire-transducers/wire-potentiometer-hps/