Emerson DIXELL XWEB1000D PRO Wiring diagram

XWEB1000D PRO

TABLE OF CONTENTS
1. PRODUCT DISPOSAL (WEEE)................................................................................................5
2. THE RECIPIENTS OF THIS MANUAL .......................................................................................5
3. PACKAGE.............................................................................................................................5
4. TECHNICAL DATA.................................................................................................................6
5. INSTALLATION......................................................................................................................7
5.1 XWEB WIRING DIAGRAMs ...................................................................................................7
5.2 CONTROLLERS................................................................................................................... 9
5.3 CONFIGURATION FOR XC400/600/800/900 and XH200/300/400 SERIES .................................. 11
5.4 CONFIGURATION FOR XJA/XJP/XJM MODELS ....................................................................... 11
5.5 USING A DC VOLT METER TOCHECK XWEB TERMINATION AND BIAS....................................... 11
6. REMOTE CONNECTIVITY ..................................................................................................... 12
6.1 DESKTOP SOFTWARE REQUIREMENTS (PC).......................................................................... 12
6.2 SOFTWARE MOBILE REQUIREMENTS (SMARTPHONE/TABLET)................................................ 12
6.3 CROSSOVER CABLE INSTRUCTIONS ..................................................................................... 13
6.4 INTRANET CONNECTIVITY (“OR LAN CONNECTION”) AND VPN................................................ 14
6.5 INTERNET CONNECTIVITY ON PUBLIC IP .............................................................................. 15
6.6 WIFI CONNECTIVITY ......................................................................................................... 16
7. CLEANOUT.......................................................................................................................... 17
8. OPERATIVE PROCEDURES.................................................................................................. 17
9. SYSTEM IDENTIFICATION.................................................................................................... 18
10. TRADEMARKS..................................................................................................................... 18
11. NOTES................................................................................................................................ 19

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 3/19
CAUTION: TO PREVENT FLAMES FROM DEVELOPING OR ELECTRIC SHOCK,
AVOID ANY CONTACT BETWEEN THISDEVICEAND RAIN OR WATER
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER IT DOES NOT
CONTAIN ANY PARTS THAT REQUIRE SERVICING BY
THE USER ALWAYS HAVE QUALIFIED STAFF
PERFORM THE PROCEDURES.
THE SYMBOL OF THE LIGHTNING BOLT INSIDE AN
EQUILATERAL TRIANGLE IS USED TO ALERT THE
USER OF THE POTENTIALLY DANGEROUS NON-
INSULATED ELECTRICAL VOLTAGES
THE SYMBOL OF THE EXCLAMATION MARK INSIDE
AN EQUILATERAL TRIANGLE IS USED TO WARN THE
USER THAT HE/SHE MUST PAY CLOSE ATTENTION
TO THE TOPIC COVERED IN THIS MANUAL
CAUTION
This device must be installed exclusively by service staff with suitable technical
training and experience,who are aware of the dangersthat they are exposed to.
The operations described herein are set forth exclusivelyfor the service staff. The
user is not enabled to open the device.
CAUTION
Use only modems and usb-donglesofficially supported by this monitoring unit. Dixell
srl. cannot be held responsible for any type of damage resulting from the use of
unsupported devices.
CAUTION
Dixell srl reserves therightto amend thismanual withoutprior notice. The latest
available version can be downloaded fromthe internetsite.
CAUTION
Immediately after the power failure,no new data is recorded; all recorded data is
kept in non-volatile memory. The memory is electronic and no data is kept or
conveyed to other media such aspaper.When the memory isexhausted,the oldest
data is lost to store the most recent data. The product provides memory
consumption indicationson the user interface.The device does not have its own
power supply. The recording interval can be configured from a minimum of 30
seconds to a maximum of1 day. The duration ofthe recordings depends on the
interval and the number of points configured for each device in configuration. One
yearof data logging is guaranteed for 2 analog resources with an interval of 15
minutes, per configured device. Selecting other resources can affect storage
performance.
CAUTION
This is a Class A product. In adomestic environment,thisproductmaycauseradio
interference in which case the user maybe required to take adequate measures
CAUTION
Dixell srl reserves therightto vary the composition of its products without prior
notice to the customer, ensuring the identical and unchanged features of the same

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 4/19
CAUTION
The product is not suitable for environments subjectto mechanical vibrations and
does not withstand shocks. It must be installed in a dryand clean environment.
CAUTION
The customer shall bear full responsibility and risk for product configuration in order
to achieve the results pertaining to installation and/or final equipment/system. Upon
the customer's request and following a specific agreement, Dixell s.r.l. maybe
present during the start-up of the final machine/application,as a consultant,
however, under no circumstancescan the company be held responsible for the
correct operation of the final equipment/system.
CAUTION
Since Dixellproducts form partof a very high level of technology, a
qualification/configuration/programming/commissioning stage is required to use
them as best as possible.Otherwise,these products may malfunction and Dixell
cannot be held responsible. The product must notbe used in any way thatdiffers
from thatstipulated in the documentation

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 5/19
1. PRODUCT DISPOSAL (WEEE)
With reference to the DIRECTIVE 2012/19 / UE OFTHE EUROPEAN PARLIAMENTAND OF THE
COUNCIL of 4 July 2012 on Waste Electrical and Electronic Equipment (WEEE), and to the relevant national
implementation regulations, we inform you thatusers of EEEin households:
➢There is an obligation not to dispose of WEEE as mixed urban waste and to separate waste collection of
WEEE;
➢Public orprivate collection systems required by local laws must be used for disposal. It is also possible,
at the end of its life,to return the equipment to the distributor in case of purchase of a new one.
➢This equipment may contain hazardoussubstances; improper use or incorrect disposal could have
negative effects on human health and the environment.
➢The symbol shown on the product or on the packaging indicatesthatthe productmustbe treated
with separate waste.
➢In case of incorrect disposal, sanctions can be applied as established by the local laws on waste
disposal.
2. THE RECIPIENTS OF THIS MANUAL
The contentsof thismanual are intended for professionalusers, such as XWEB installers.It may also be of
use to the administrator of the network that it is connected to.
The mechanical product drawings required for any form of intervention and the possible network
configurationsare all an integral part of this manual.
3. PACKAGE
Before opening the package make sure that the packaging is intact and thatthere is no sign of impact or
tampering. Before starting any operation, itis necessaryto checkthat the XWEB box contains:
•1 XWEB Unit
•1 Installation Manual
•1 Cross Cable 1mt
•Removable female connector
1x2 ways,
5x3 ways
1x4 ways
1x6 ways
•jumpers
If one of the following parts is damaged, promptly contact yourdealer.
You may also receive a modem or a wifi dongle- which will not be included in the same package - as a
package option.When working with a modemconnection, alwayscheck that the type of modem you are
about to install is a Dixell approved model;as it cannot be held responsible for the malfunctioning of devices
not expressly approved by it.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 6/19
4. TECHNICAL DATA
XWEB is DIN Rail mounting compatible. Snap the orange tabs on the back of theunit to the down position to
fasten. If not using the DIN Rail mounting option, fasten to the mounting surface using the openings in the
mounting tabs.
Dimensions
183 x 110 x 59.1 mm
Weight (without
accessories)
436g
Mounting
DINrail mounting device
Degree of Protection
Indoor use, Open Type (NEMA - UL 50e)
Enclosure Rating
UL 94 V-0
Power
24Vac, 20VA
Overvoltage Category
II
Rated Impulse Voltage
2500V
Type of Action
1.B of N.O.;1.Cof N.C. (Relay1-4)
PollutionDegree
2
Ambient Operating
Temperature
-40 to 140 °F (-40°Cto 65°C)
Shippingand storage
temperature
-40÷85 °C
Relative Humidity
20-85% RHnoncondensing
Digital Inputs
2, Dry contacts
Relay Outputs
3
Digital Output Ratings
Relay 1 (N.O. & N.C.) 5A, 125/240 VAC, General Purpose, 100K
cycles; 4FLA/4LRA, 250VAC,MotorLoad,100K cycles;
Relay 2 (N.O. & N.C.) 5A, 125/240 VAC, General Purpose, 100K
cycles; 4FLA/4LRA,250VAC, Motor Load, 100K cycles;
Relay 3 (N.O. & N.C.) 5A, 125/240VAC, General Purpose, 100K
cycles; 4FLA/4LRA,250VAC, MotorLoad, 100K cycles;
RS485 ports
MODBUS Com Ports1, 2, 3, 4
Ethernet ports
Ports ETH1, ETH1, ETH0 (ETH1 has no IP)
USB Ports
1
MicroSD
1
Purpose of control
Operating control
Construction of control
Incorporated control, intended to be used in Class Ior Class II
equipment
Approvals
CE

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 7/19
5. INSTALLATION
5.1 XWEB WIRING DIAGRAMS
For installation, the XWEB systemmust notbe opened in any way. If the boxis opened, the warranty will
lapse. XWEB-EVO can be installed in various ways based on the model and type of user interface access
that you wish to provide for the final user. The features ofthesetypes of connectivity are described herein.
CAUTION: in order to protect yourself and the XWEB, turn on the unit only after connecting all the electrical
devices. In order to avoid accidentaloperation,connect the power cord only after connecting all the other
external units.
1-2
Powersupply24Vac
USB ext. peripherals
ETH0, ETH1
RJ45 LAN connector
-
+
Cmn
61
62
63
64
65
66
67
68
69
31
32
33
RS485
COM1, COM2, COM3,
COM4
Relay 1
(System alarm relay)
Relay 2
(AUX1)
Relay 3
(AUX2)
Digital Input1
Digital Input2

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 8/19
LEDS
•“Rectangle LED”: Poweron / Cleanout
•“Triangle LED”: Alarm / Cleanout
Micro SD
Removable storage media currently used for Backup / Restore functions.
Note: The media must alreadybe inserted at the XWEBEVO poweron. It is notmounted "on the fly"
Reset Button
As long asit is pressed, the deviceis off. Verysimilar to the reset button on PC
On release, the system restarts asper power on.
•Avoid direct passage between operators as much as possible (to avoid electrostatic
induction and subsequent discharges);
•If the electrical voltage supply differs from the required rating, this could seriously damage
the system;
•Connection errors (and connections that differ from the prescribed ones) can pose a danger
to operator safety and cause faults in the system and to the instruments that are connected
to it;
•Insert one or more easily accessible disconnecting devices to the exterior of the device to
separate the device from the power mains;
•Do not use the device in environments with flammable gases.
•Do not modify the device in any way.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 9/19
5.2 CONTROLLERS
XWEB has at least one RS485 serial port, on which the line of the controllerdevicescan be connected. If
there are more serials,more device lines can be served.
Most Dixell controller devices are equipped with an RS485 serialoutput and can be connected without the
need for any additional module or connection cable. To make sure of this possibility, check the
characteristics of the controller in its manual.
Some Dixell devices however, may not be direct, but it can be obtained via the small external Dixell
XJRS485 or DixellXJ485 converter. It converts the controller outputfrom"TTL" (five wires) to "485" (two
wires). If you need to use the TTL / 485 converter, please pay attention in:
•Keep the TTL cable away from any source of electromagnetic disturbance
•Connect each XJ485 module to the instrumentwith the TTL cable supplied with the module itself
•Mark the polarity of output 485 which must be respected when connecting the instruments to the
network
Below is a list of operating tips to obtain the best result in termsof instrument network reliability, RS485
serial connection:
•The serial line cable can be of the two-wire type plusthe shield, with a minimumsection of 0.5mm2
(eg BELDEN 8772).This cable is recommended for its technical characteristics and for maintaining
the quality of the electrical signal;
•The serial line cable must reachall the instrument stations: check the plant layout and the various
distances thatthe cable will have to travel;
•The serial line cable can reach a maximum length of 1 km
•Respect the polaritiesindicated on the instrument withthose of the cablesleading to the serial
•Keep the serial cable away from power cables and any possible source of electromagnetic
disturbance
•Do not connect the shield of the serial cable to the earth of the electrical system
•Do not connect the “Gnd” terminal.
•Drawa map of the installation you are performing: it will beusefulboth in case of problems and in
case of future changes; the serial line must reach all the stations where the instruments must be
controlled.

1592010930 XWEB1000D PRO STP GB r1.0 25.11.2020.doc XWEB1000DPRO 10/19
•Do not branch into the line:
Correctconnection
Incorrectconnection
On the same line, each controller is normally programmed with its own unique serialaddress, through the
Adr parameter. Refer to the installation manual of the instrument itself for the access and modification
procedure. To obtain a simple description of the categoriesto which they belong,divide the programming of
the addresses progressively.Some special cases are listed on the following pages.
To keep the RS485 line balanced,the ends must be terminated with a 1500Ω resistor. If the XWEBis at one
end of the RS485 line, it is advisable to insert the 120Ω termination resistor on the last instrument and on the
XWEB. To activate the EOL resistor,insert enable TERM. DO NOTenable it if the XWEBis in the middle of
the RS485 line.
SW
On/Off
Pos1
Term
Pos2
Bias