Elechomes CHS2003 User manual

Model: CHS2003
H i g h S p e e d
Blender
User Manual

This kitchen high-speed blender uses high-speed motor to provide power for
rotating stainless steel blade assembly to achieve the purpose of chopping
ingredients. Featuring refined motor with adjustable rotating speed as well as
unique blade and PC jar structure, it can achieve a variety of blending effect.
Product Introduction Product Illustration
Bearing imported from Japan, the rotating speed of this motor reaches
up to 30000r/min with little noise. With fan cooling device, the blender
can run for a long time to meet the commercial premises requirements.
Motor has designed with overheat protection device to prevent burning.
The machine is equipped with circuit system to control the rotating speed,
stabilize current, protect the motor and reduce external interference.
The machine is equipped with over-current protector which can protect
the device when current or voltage fluctuates.
The machine has a speed tuning switch and momentary switch, hence
can provide a variety of mixing effects.
The rotating connector of the machine is a pair of upper and lower
stainless steel parts, so it will not be damaged.
The waterproof glue on the bearing is made of special wear resistant
material which is hard to wear for a long time.
The specially processed blade assembly is hard enough to chop or grind
herbs, beans and other ingredients.
Its PC jar is made of imported PC material and undergone high temperature
processing, wear resistant and crash resistant.
If the power cord is damaged, it can only be replaced or repaired by
manufacturer's service department staff or equivalent personnel in order
to avoid danger.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Stir Bar
Speed Tuning Knob
Power Switch
Motor
Refill Cover
Jar Lid
Tritan Jar
Blade Assembly
Securing Plate
Instantaneous
Rotation Switch
Body Cover
Stand Base

Place the high-speed blender on a flat platform due to its high power
motor.
Make sure the jar is completely attached to the stand base before power
the device on.
Please be careful not to touch the power switch before or after startup.
Please hold the device during working time so as to avoid the dumping
caused by vibration.
Do not use the stir bar in the rotation of motor to avoid danger.
Make sure to cover the jar with refill cover to avoid food spillage when
using the stir bar.
Keep your kids away from the running device to avoid accidental danger.
Pour the ingredients out of jar after shutting the device down and its blade
assembly stops working.
Do not insert your hands into the jar unless the blade assembly has been
removed.
Be sure to unplug the plug after each use.
1.
Operation Instruction
Do not put metal objects into the jar such as knives, forks, spoons etc.
Using the Stir Bar
Blade Category
Professional combo cutter for smoothie / fruit and vegetable juice
Crush ice blocks and stir smoothie
For Dry or Wet Use
Dry use --- Chinese herbal medicines, coffee beans, cereals, stone fruit
and so on
Wet use --- fruits and vegetables, wheatgrass, pasture, fruit juice and so on
Adjustable Rotating Speed
Use as a mixer in slow rotating state
User as a crusher in high rotating state
Stop use the device for 1 min after continuous 3 min working in high-
speed state. It can be operated continuously for over 10 times.
Note:
Note:
Place the jar firmly on the stand base.
Check that the power switch is pushed down to the "OFF" position.
Pour ingredients into the jar. Inject some fluid(water, milk, honey, fruit
juice etc.) into jar too if you want to crush solid ingredients.
Cover the rubber jar lid and/or place in the stir bar, and last place back
refill cover.
Plug the power plug to power socket, hold the jar and then push the
power switch to “ON” position.
Set the rotating speed by rotating the speed tuning knob according to
ingredients as below.
Push the power switch to the "OFF" position to turn off the device.
How to Use
Place into ice blocks, fruits and water. All of them are indispensable.
After pouring the ingredients into the jar, cover the jar lid and refill
cover. If you want to make thick drink, insert the stir bar into refill cover.
Tune the rotating speed into a higher or the maximum speed.
Push the power switch to ON position to start crush ingredients. Please
stir the ingredients via stir bar if you injected a small amount of water.
When the collision sound of ice blocks is reduced suddenly, all the
ingredients have been crushed. Immediately shut down the device to
prevent ice blocks from becoming water due to excessive mixing.
Make Icy Fruit Juice
Place in clean fruits or vegetables and inject a small amount of water.
Set the rotating speed to a medium or high speed position.
Push the power switch to ON position to start crush ingredients. About
4-6s later, the ingredients in the jar are rolling up and down, indicating
that all ingredients have been chopped. Stop use at once to prevent over
chopping from damaging their vitamins.
Make Fruit/Vegetable Juice
Safety Precautions
2.
3.
4.
5.
6.
7.
10.
1.
2.
1.
2.
First remove the refill cover and then insert the stir bar into its hole
1.
2.
3.
4.
5.
1.
2.
3.
4.

Please stir the ingredients via stir bar or inject some water if there is a
small amount of water in the jar.
High-speed rotation is used to test machine performance and crush
special ingredients, but do not use this mode frequently.
Do not let the blade assembly rotate without liquid for more than 2 minutes,
because it generates ultra-high temperature to burn bearings.
Note:
Clean and Maintenance
Add 750ml water and 1-2 slices of lemon into the jar, then switch on the
device to run for 2 minutes.
Drain the water and repeat step 1 again.
Drain the water and lemon, and use a sponge or dry cloth to carefully
clean the jar and jar lid.
Horizontally place the jar or place it upside down after clean and let it air
dry.
If the jar has been put upside down for air dry, please wipe the bottom of
the jar and keep it away from stand base to prevent accidental drip back
to its bottom, resulting in bearing rust or damaging the jar.
Use a dry cloth to wipe the rotating shaft and the motor base (remember
do not rinse them with water). If it's hard to wipe clean somewhere, do it
with neutral detergent first and then wipe clean with a dry cloth.
Be sure to disconnect the power and the power switch must be in the
OFF position before cleaning and maintenance.
Be sure to wait until the blade assembly stops rotating completely before
opening the lid.
Do not put the jar into dishwasher for cleaning, and do not soak it in water.
Do not insert your hands into the jar for cleaning unless the blade
assembly has been removed.
Be sure to separately dealing with base and jar cleaning. Wipe the stand
base with a clean soft cloth instead of rinsing it under water. Use a soft
cloth or sponge to gently wipe the surface of the jar, however the
measuring cup on the jar lid and seal ring can be rinsed under water.
FAQ and Solution
There is no reaction after powering on.
Check if the over-current protection is off(control button locates at the
bottom of base). Try to press the button again.
Check if the plug is connected.
Check whether the fuse or automatic switch is in closed circuit.
Please check whether there is power failure.
If there is no problem about above conditions, please contact our
customer service team or send it for professional repair.
Specifications
Input: 110~125V 60Hz
Power: 1200W
Max. Rotating Speed: 28000 r/min
4.
1.
2.
3.
4.
5.
Note:
1.
2.
3.
4.