Element 8085 User manual

HI-DEFINITION A/V ROUTING SYSTEM
Version 1.0
Please read this user manual carefully before using this product.
Failure to understand operation procedures may result in injury.

C O N TE N TS
01
Brief Introduction
Product Features
Technical Specications
Packing List
Installation and Use
Meanings Of Indicator Statuses
Specications
FCC Information
Contents
Structure
FAQs
Back cover
2
2
4
3
4
7
10
11
12

02
Brief Introduction
Product Features
Thank you for choosing our ELEMENT8085 high-denition
(HD) wireless audio/video (AV) transmission system devices. The
device can be wirelessly connected from an HD source device to
an HD display device such as TV, projector, HD disc player, game
machine, recorder, and set-top-box at home. With the device, you
can enjoy HD video anywhere at home. In addition, you are
relieved from the cost and hassle of running cables to complete
your installation.
Instant wireless HD AV transmission;
Transmission range indoors 30m;
Supports video HDMI interface at a maximum of 1080P 60 Hz;
Supports HDMI1.3 and HDCP1.2 protocols;
Supports EDID function;
Supports CEC function (for the receiving and display devices);
Supports IR extension transmission function;
Transmission power 12 dBm;
Supports point-to-point transmission function which can currently be
expanded to point to multi-point or multi-point to multi-point
transmission function;
Supports AES128-bit image encryption function;
Supports reverse back-transmission channel at the maximum
rate of 100 kbs;
Supports OSD display;
Supports WHDI 1.0 specication.

03
RF communication system
Modulation mode
Maximumtransmission power
MIMO
OFDM
12dBm
Technical Specications
* The working frequency band may vary with the relevant laws in
dierent countries or regions.
Video formats supported
TV 1080p, 1080i, 720p, 576p,480p
PC: VGA(640X480), SVGA(800X600),
XGA(1024X768), SXGA(1280X1024)
PCM,DTS, DOCBY DIGITAL
<1 ms
Built-in
5.1~5.9GHz
38KHz
100-240V AC mains, 5V 2A DC power
O
-10~50 C
Audio formats supported
Imagetransmissiondistance
Image delay
Transmission/receiving
antenna mode
Operating frequency
IR carrier modulation
frequency supported
Operating power supply
Storage temperature
30m
O
-20~80 C
Storage temperature

04
HD wireless video
transmitter x 1 HD wireless video
receiver x 1 Base x 2
IR remote extension
connector x 1 Power supply x 2
Packing List
Structure
Transmitter
2
3
1
6
4
5
1Power Input Port
This port is connected to the 5V/2A power adapter which is
5.5mm in diameter and positive outside and nega tive inside.

05
4
5
6
3
2
Connector
HDMI Input Port
This port is connected to a video cable supporting the HDMI1.3
protocol.
Output Interface for IR Remote Signals
This interface is connected to an IR extension cable for extending
the IR remote receiving function.
Wireless Network Status Indicator
If this indicator turns green after the power supply is connected,
it indicates that wireless network connection is made successfully;
if this indicator is not ON, it indicates that wireless network
connection fails to be made; if this indicator ashes, it indicates
that the device is faulty.
Video Status Indicator
If this indicator turns green after an HDMI cable is connected,
it indicates that video connection is made successfully; if this
indicator is not ON, it indicates that video connection fails to
be made.
Code Key
This key functions to: 1. Enhance transmission distance: When
the distance between a transmitter and a receiver exceeds the
transmission distance, press this key on the transmitter or
receiver to enhance the transmission distance. The picture
quality, however, deteriorates; 2. Enable the code matching
function: Press this key on the transmitter and the receiver for
3 seconds at the same time, the codes of the machines will be
matched again automatically.
2
3
1
4
5
6

06
2
1
3
4
5
6
Power Input Port
This port is connected to the 5V/2A power adapter which is
5.5mm in diameter and positive outside and negative inside.
HDMI input port
This port is connected to a video cable supporting the HDMI1.3
protocol.
Output Interface for IR Remote Signals
This interface is connected to an IR extension cable for extending
the IR remote receiving function.
Wireless Network Status Indicator
If this indicator turns green after the power supply is connected,
it indicates that wireless network connection is made successfully;
if this indicator is not ON, it indicates that wireless network
connection fails to be made; if this indicator ashes, it indicates
that the device is faulty.
Video Status Indicator
If this indicator turns green after an HDMI cable is connected,
it indicates that video connection is made successfully; if this
indicator is not ON, it indicates that video connection fails to
be made.
Code Key
This key functions to: 1. Enhance transmission distance: When
the distance between a transmitter and a receiver exceeds the
transmission distance, press this key on the transmitter or
receiver to enhance the transmission distance. The picture
quality, however, deteriorates; 2. Enable the code matching
function: Press this key on the transmitter and the receiver for
3 seconds at the same time, the codes of the machines will be
matched again automatically.
IR Remote Receiving Window
Its function is the same as that of the remote receiving window
on a set-top-box. The video source can be controlled remotely
by pointing at this window.

07
Installation and Use
* It is recommended to place a transmitter and a receiver verticall
or horizontally at the same time during installation.
If the transmitter and the receiver are placed across each other, for
example the transmitter is put vertically and the receiver is
placed horizontally, the image transmission distance may be aected.
Installation for Transmitter
1. Install the transmitter on a base and then place the transmitter
in a suitable position beside an HD video source.
Note:
* Put the antenna end upward.
* Do not place any article on the transmitter or beside it to avoid
aecting the transmission distance and image eect.
2. The wireless network status indicator is ON after the transmitter
power supply is connected and wireless network connection i
made successfully.
3. The videostatusindicatoris ON afterthe transmitterisconnected
tothe video output socket of the HD source with an HD AV cable.

08
* Any video source with the HDMI video output interface can be connected.
4. Connect the IR remote extension connector to the IR remote
signal output hole of the transmitter.
Installation and Use for Receiver
1. Install the receiver on another base and place the receiver
beside an HD display device in another room.
Note:
* Put the antenna end upward.
* It is not recommended that you place any article on the receiver
or beside it to avoid aecting the receiving distance and image
eect.
HD MI OUT
DVD player
Set-top-box
Game machine
POO3

09
* The transmission distance between the transmitter and the
receiver is 30 meters at most. If signals are obtained by
penetrating a wall, the transmission distance and may be aected.
2. The wireless network status indicator is ON after the receiver
power supply is connected and wireless network connection is made successfully.
3.3. Connect the receiver to the HD display device with a standard
HD AV cable. The video status indicator on the receiver is ON after
video connection is made successfully. Images appear on the display device.
4. The video source can be controlled remotely by pointing the
remote control at the IR receiving window on the receiver.
* Any display device with the HDMI video input Interface can be connected.
Note: This product matches only with
an IR remote control in the 38 KHz carrier modulation mode.
HD MI IN
HD projector
HD TV