eletab ELTGM03-2 User manual

PRODUCT LINE GRAPH
CAUTION:
IMPORTANT:
Read the entire instrution manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, Please
contact at [email protected] for assistance.
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
Ensure that you have received all parts according to the component checklist prior to
installation. If any parts are received damaged or defective, please contact us at
[email protected]. We are happy to replace parts to ensure you have a fully
functioning product.
• Mounts must be attached as specified in assembly instructions. Improper installation
may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by
professionals.
• Make sure that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep
these items away from children.
• This procuct is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
270
360
180
180
100mm
min10mm-
max85mm
75mm
100mm
115mm
75mm
100mm
115mm
min170mm-max505mm
-90
+90
210mm min255mm-max315mm 80mm
50mm
1

Tools required
Components
Hardware
Parts
B (x2)
VESA Plate
I(x1)
Support Plate
J(x1)
Knob
G (x5)
Bolt
M4x12mm (x4)
M-A
Screw
M5x12mm (x4)
M-B
Screw
D5 (x4)
M-C
Washer
C (x1)
Clamp Base
Support
D (x1)
Clamp
E (x1)
Decorative
Cover
F (x1)
Long Screw
H(x1)
Base Support
A (x1)
Arm
X2
L(x1)
4mm Allen
Wrench (not included)
Phillips
Screwdriver
M(x1)
6mm Allen
Wrench
K(x4)
Pad
2

Attach the Arm to the Desk
For the Desktop with Thickness of
10-55mm
For the Desktop with Thickness of
50-85mm
of the arm
to the base.
3

Attach the decorative cover (E) to the clamp base support. Fit clamp to the desk and turn the
plastic knob counter-clockwise to tighten the connection.
Assemble the base support (H) to the base with long screw (F) and bolts (G)using 4mm Allen wrench (L).
the base.
4

Attach the Monitors to the Arm
Insert the long screw through the hole on the desk and attach the base to the desk using the support plate (I)
and the knob (J). Turn the knob counterclockwise to tighten the connection.
Attach VESA plate (B) to the monitor with washers
(M-C) and screws (M-A) or (M-B)
Pull the tab on the arm (A) ①and attach the monitor
to the arm. ②
5

Case 1: Monitor/Arm Falls Down (After Install Your Monitor)
When the monitor is too heavy, turn the 6mm Allen wrench counter-clockwise to increase
tension till it can hold the weight of your monitor.
fall down
Adjust the Gas Spring Tension
Be sure to keep the arm in horizontal
position during adjustment. 0r else it
would be difficult to adjust the mount or
damage the mount.
Once the monitor is attached to the arm, use the 6mm Allen wrench(M)and turn in the
appropriate direction to increase or decrease tension as necessary. Heavier monitor turns
counter-clockwise. Lighter monitor turns clockwise. Adjust the tension of the gas spring
until the monitor holds its position when you let it go.
(Note: DO NOT overtighten screw.)
6

Case 2: Monitor/Arm Pops Up (After Install Your Monitor)
When the monitor is too light, turn the 6mm Allen wrench clockwise to decrease tension
till the monitor can stay at the desired position.
pop up
Case 3: Monitor Tilts Forward
If needed, tilt the monitor using the 6mm Allen wrench to your desired angle.
7

Remove the upper and bottom cable covers as shown.
Route cable along the arm as shown and reattach the upper and bottom cable covers.
Cable Management
8

L M
Wrenches
9