StarTech.com SHELF-2U-14-CENTER-V User manual

Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: April 27, 2022 3:01 PM
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Product IDs
SHELF-2U-14-CENTER-V
SHELF-2U-20-CENTER-V
Product Diagram
Front - Angled View
Component Function
1Shelf Lip
• Mount the 2U Vented Center-Mount Shelf with the
Shelf Lip oriented upwards to prevent Equipment
from slipping o
2Mounting Holes (x 8) • Mount the 2U Vented Center-Mount Shelf into a
Rack.
Product Information
For the latest manuals, product information, technical specications, and declarations
of conformance, please visit:
www.StarTech.com/SHELF-2U-14-CENTER-V
www.StarTech.com/SHELF-2U-20-CENTER-V
Requirements
• 2U Available Rack Space
• Phillips Head Screwdriver
• (Optional) Cage Nut Tool
2U Vented Center-Mount Shelf - 14/20 in. Depth
Warnings
• Read the entire manual and ensure the instructions are fully understood before
assembling and/or using this product.
• Before adding equipment to this product, ensure this product has been properly
mounted.
• Ensure the weight of the equipment does not exceed the weight capacity of this
product. If the weight capacity is exceeded, personal injury or damage to the
equipment are possibilities. This product can support the following weight: up to
200.6 lb. (91 kg). This product can only support the maximum weight capacity if 8
M6 Screws / Cage Nuts / Plastic Washers are used to ax this product to a rack.
Package Contents
• 2U Vented Center-Mount Shelf x 1
• M6 Cage Nuts x 10
• M6 Screws x 10
• M6 Plastic Washers x 10
• Quick-Start Guide x 1
Installation
Mount the 2U Vented Center-Mount Shelf into a Rack
Use the included M6 Cage Nuts, M6 Screws, and M6 Plastic Washers to install the 2U
Vented Center-Mount Shelf.
Notes: This product can support the following weight: 200.6 lb. (91 kg).
The following installation instructions are for square mounting holes.
1. Locate a suitable location in a Rack to mount the 2U Vented Center-Mount Shelf.
Note: The 2U Vented Center-Mount Shelf itself requires 2U of space within a Rack.
2. Insert the Wing (side) of an M6 Cage Nut into the back of the a Cage Nut Hole.
3. Insert the second Wing of the M6 Cage Nut into the selected Cage Nut Hole, using
pressure by hand, or with a Cage Nut Tool.
4. Repeat steps 2 and 3 to insert a total of 8 Cage Nuts.
5. Thread an M6 Plastic Washer over an M6 Screw. Repeat until 8 M6 Screw
Assemblies have been prepared.
1
*Product may vary from image
2

6. Align the Mounting Holes in the 2U Vented Center-Mount Shelf with the M6 Cage
Nuts installed in steps 2-4.
7. Insert the M6 ScrewAssemblies through the Mounting Holes in the 2U Vented
Center-Mount Shelf and into the M6 Cage Nuts and tighten, using a Phillips Head
Screwdriver.
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands