Eliminator BUBBLE STORM LED User manual

ENGLISH
Congratulations to the purchase of this sinfen bubblemachine. Please read this manual thoroughly prior to using the unit in
order to benefit fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to
avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock.
Keep the manual for future reference.
- Prior to using the unit, please ask advice from a
specialist. When the unit is switched on for the first time,
some smell may occur. This is normal and will disappear
after a while.
- The unit contains voltage carrying parts. Therefore do
NOT open the housing.
- Do not place metal objects or pour liquids into the unit
This may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as
radiators, etc. Do not place the unit on a vibrating
surface. Do not cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical shock
and malfunction.
- When unplugging the unit from a mains outlet, always
pull the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
-If the plug and/or the mains lead are damaged, they
need to be replaced by a qualified technician.
-If the unit is damaged to such an extent that internal
parts are visible, do NOT plug the unit into a mains outlet
and DO NOT switch the unit on. Contact your dealer. Do
NOT connect the unit to a rheostat or dimmer.
- To avoid fire and shock hazard, do not expose the unit to
rain and moisture.
- All repairs should be carried out by a qualified technician
only.
- Connect the unit to an earthed mains outlet (220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used for a
longer period of time, unplug it from the mains. The rule
is: Unplug it from the mains when not in use.
-If the unit has not been used for a longer period of time,
condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the unit in
humid rooms or outdoors.
- During operation, the housing becomes very hot. Do not
touch it during operation and immediately after.
- To prevent accidents in companies, you must follow the
applicable guide lines and followthe instructions.
- Secure the unit with an extra safety chain if the unit is
ceiling mount. Use a truss system with clamps. Make
sure nobody stands in the mounting area. Mount the
effect at least 50cm away from inflammable material and
leave at least 1 meter space on every side to ensure
sufficient cooling.
- This unit contains high intensity LEDs. Do not look into
the LED light to prevent damage to your eyes.
- Do not repeatedly switch the fixture on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not leave
the unit unattended.
- Do not use cleaning sprays to clean switches. The
residues of these sprays cause deposits of dust and
grease. In case of malfunction, always seek advice from
a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
-If the unit has fallen, always have it checked by a
qualified technician before you switch the unit on again.
- Do not use chemicals to clean the unit. They damage the
varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the unit off prior to unplugging it from the mains
and/or other equipment. Unplug all leads and cables
prior to moving the unit.
- Make sure that the mains lead cannot be damaged when
people walk on it. Check the mains lead before every use
for damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if power
outlet match. If you travel, make sure that the mains
voltage of the country is suitable for this unit.
- Keep the original packing material so that you can
transport the unit in safe conditions
This mark attracts the attention of the user to high voltages that are present inside the housing andthat are of sufficient
magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructionsthat are contained in the manual andthat he should
read and adhere to.
DO NOT LOOK DIRECTLYINTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks
should be aware of the effects that this light effect may have on them.
The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and
their guarantee!
NOTE: To make sure thatthe unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and
35°C/95°F.
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your
dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other.
Specifications can be changed without prior notice.

UNPACKING INSTRUCTION
CAUTION! Immediately upon receiving, carefully unpack the carton, check the contents to ensure that all parts are present, and
have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts
appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In
the event that a bubble machine must be returned to the factory, it is important that the bubble machine be returned in the
original factory box and packing.
If the bubble machine has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached
room temperature.
POWERSUPPLY
On the label on the backside of the bubble machine is indicated on this type of power supply must be connected. Check that the
mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The bubble
machine must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.
Always connect the bubble machine to a protected circuit (circuit breaker or fuse). Make sure the bubble machine has
an appropriate electrical ground to avoid the risk of electrocution or fire.
INSTALLATION
Attention:
• Be sure that the bubble machine is positioned on a stable, non-slip surface.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Don’t put any objects on the bubble machine.
• Never connect the bubble machine to a dimmer or rheostat.
• Keep the housing of this bubble machine dry at all times.
• Do not spill water or other liquids into reservoir.
• Drain the reservoir before transporting or storing the product.
• Never drink bubble liquid or use it on the inside or outside of a human body. If fluid gets in contact with skin or eyes,
rinse thoroughly with water and call a doctor immediately!
• Keep out of the reach of children.
• For indoor use only.
CAUTION: Please consider the respective national norms during the
installation! The installation must only be carried out by an
authorized employee or dealers!
CAUTION:
When installing the fixture, make sure there is no highly in
inflammable material (decoration articles, etc.) in between a
distance of min. 20in or 0.5 meter.

FILLING RESERVOIR
Before filling unplug from mains!
•Place the unit on a at, stable surface which must not be tilted more than 10° (see drawing)
•Fill the tank up to the marking with a good quality bubble uid .
•Switch the unit on via the On/O switch on the rear side.
•Switch the unit o after use and unplug it from the mains if it will notbe used for a long period of time.
•Rinse the unit regularly with clean water.
OPERATION
Once the reservoir has been filled Connect the power lead into smoke machine and earthed mains outlet . Then you can switch
the power on. By pressing the switch on the remote control, the machine start producing bubble .
Switch o when machine not used and unplug from mains if not use for long periods.
0 = OFF
I = ON
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuse holder on the rear panel with a tting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the newfuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
ACCESSORIES
High quality bubble uid, specially designed for bubble machines guarantees a trouble -free use with a lot of bubbles.
10
10
10
10
PLEASE DON'T FILL OVER THE LINE!
1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our
1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.
WARRANTY