Elinz BCSMART20 User manual

www.elinz.com.au / [e-mail] / 1300 881 773
BCSMART20 8-Stage Automatic Battery
Charger Instruction Manual
WARNING
Risk of chemical burns!
Batteries contain acid, which could damage the eyes and skin.
Charging batteries further generates gasses and vapors hazardous to
the health.
Avoid any contact with caustic battery acid, immediately thoroughly
flush skin and any objects which have come into contact with acid. If
eyes have come into contact with battery acid flush eyes with running
water at least 5 minutes. Contact your physician.
Use safely googles and acid-proof safety gloves. Protective clothing,
e.g. with an apron.
Never tip the battery, as acid may leak.
Always ensure adequate ventilation.
Do not inhale emerging gasses and vapors.

www.elinz.com.au / [e-mail] / 1300 881 773
Explosion and fire hazard!
Gaseous hydrogen (detonating gas) may form when charging the
battery. Contact with open fire (flame, embers, sparks) may result in
explosions.
Never charge the battery close to an open fire or in places where
sparks may occur.
Always ensure sufficient ventilation.
Be sure the power supply voltage matches the input voltage specifies
on the device (220-240V AC) to prevent damage to the device.
Only connect and disconnect the battery connecting cables when the
charger is disconnected from the mains.
Do not cover the device while charging, as it may be damaged from
extreme heating. Immediately stop using the device if you notice
smoke or an unusual odor.
Do not use the device in rooms where explosive or flammable
substances are stored (e.g. petrol or solvents).
Risk of Electrical Shock!
Charges may interfere with the operation of active electronic
implants, e.g. pacemakers
Avoid pouring or dripping water or other liquids over it. If water
penetrates electrical devices, the risk of electric shock increases.
Ensure that all plugs and cables are free of moisture. Never connect
the device to the mains with wet or moist hands.
Never touch both connections at once when the device is in use.
Unplug from mains before connecting or disconnecting the charging
cable with the battery, or when the device is no longer being used.
Remove all the device cables from the battery before attempting to
drive your vehicle.

www.elinz.com.au / [e-mail] / 1300 881 773
Always unplug device by the plug. The cable may be damaged.
Do not use device if damaged. Damage to the power cable, the device
or the charging cable increase the risk of electrical shock.
Do not attempt to disassemble or repair the device. Immediately
have a defective device or damaged power cable repaired or replaced
by a specialty shop.
Risk of short circuits! Do not allow the two connectors from the
charging cable to touch if the power plug is plugged into the power
outlet. Be sure not to connect the connectors or the battery poles
through conductive objects (e.g. tools).
Never use the cable to carry or pull the device.
Risk of Injury!
Never attempt to charge non-rechargeable, damaged or frozen
batteries.
Do not use this device to charge dry cell batteries. These could burst,
resulting in personal injury and property damage.
Please read and follow the operating manual and all safety
instructions for the batteries to be charged and the vehicle before
using this device.
Risk of damage!
Never place the device over or near the battery to be charged. Gasses
from the battery could damage the unit. Place the device as far from
the battery as the connecting cable will allow.
Never operate the device if it has been dropped or damaged in any
other way. For inspection and repair, take it to a qualified electrician.

www.elinz.com.au / [e-mail] / 1300 881 773
Safety Functions
The charger features the following safety features to prevent damage
to the charger and the battery or the vehicle:
Short circuit protection
Reversed polarity protection
Overheating Protection
Excess current
Overcharge protection
LCD Display

www.elinz.com.au / [e-mail] / 1300 881 773
Operation
Before use
Before connecting the charger, the operating instructions must be
observed. Furthermore, the instructions of the vehicle manufacturer
regarding a permanently connected car battery must be observed.
Secure the car, switch off the ignition. Clean the battery poles. Take
care that while doing so, your eyes do not come into contact with the
dirt.
Ensure sufficient ventilation.
Connecting
Connect the "+" pole clamp (red) of the charger to the "+" pole of the
battery.
Connect the "-" pole clamp (black) of the charger to the "-" pole of
the battery.
Connect the main cable with AC 230V VDE plug of the charger to the
main socket.
Before start charging, please press the Button to select with
mode you want.
Then press the Button . The charger to start to work.
If you want to stop charging, please press the Button .
The battery voltage display shows the current battery voltage after
connecting.
If the connecting is "Reverse" or "Short Circuit", "Err" will be displayed
on the screen.
The charger can automatically recognize and choose 12V or 24V after
connecting.
LCD display can automatically show the percent of voltage.

www.elinz.com.au / [e-mail] / 1300 881 773
Disconnecting
Disconnect the appliance from the main supply.
Remove the "-" pole clamp (black) from the "-" pole of the battery
Remove the "+" pole clamp (red) from the "+" pole of the battery.
Specifications:
Charging type
8-Stage Automatic
Input voltage
220-240V AC/50Hz
Input power
350W
Output voltage
12V DC and 24V DC
Max output current
Max 20A for 12V and Max 10A for 24V
Minimum Start voltage
4.2V
Back Drain
0mA
Current fuse rating
UL 250V/10A(PCBA)
Efficiency
85%
Thermal Protect
≥80℃±5℃), the charging currents drops to 2A, and
≤70℃±5℃recover normal currents
Battery types
Lead-Acid, Wet, MF, AGM Calcium, Gel
Cooling fan
Automatic temperature controlled
Ambient temperature
-20℃to +40℃
Over voltage protection
Please see details below
Battery range
12V 50-400Ah, 24V 25-200Ah
DC charge cable Length
DC cable to Anderson connector 1.5M / Clamp cable
with Anderson connector 0.3M
Normal (12V Mode) - When the battery voltage more than
14.3V±0.3V, the charger stops working
Low temperature (12V Mode) - When the battery voltage more
than 14.7V±0.3V, the charger stops working
Normal (24V Mode) - When the battery voltage more than
28.6V±0.3V, the charger stops working
Low temperature (24V Mode) - When the battery voltage more
than 29.4V±0.3V, the charger stops working

www.elinz.com.au / [e-mail] / 1300 881 773
8-STAGE AUTOMATIC CHARGING
This is a fully automatic battery charger featuring 8 charging stages
Stage 1 &2 Test and Diagnostics
Checks the battery’s initial condition, including voltage, state-of-charge
and health, to make sure battery connections are good & battery is in a
stable condition
Stage 3 Soft Start
Starts the charging process gently to ensure an even flow across each
cell before increase the charging rate
Stage 4 Bulk Charge
Allows the full voltage/current output of the charger required by the
battery (depending on the chemistry mode selected)
Stage 5 Absorption
Automatically reduces the current output whilst maintaining the
required voltage.

www.elinz.com.au / [e-mail] / 1300 881 773
Stage 6 Trickle
Battery is fully charged and ready to use, in this step, the battery charger
will only deliver enough current to keep the battery full. If the battery
tells the charger that more current is needed, the battery charger will
switch to Maintenance.
Stage 7 Maintenance
Continuously monitors the battery to determine when a maintenance
charge should be initiated. If the battery voltage falls below its target
threshold, the charger will restart the Maintenance cycle until voltage
reaches its optimal state and then discontinues the charge cycle.
Stage 8 Silent Night Mode
The Silent Night Mode is used to provide quiet operation by reducing
the charge current to 2A and disabling the internal cooling fan.
For any inquires, issue or comments concerning our products, please send us
an email to the address below and we will respond as soon as possible.
Feel free to contact us at 1300 881 773, send us an email at
[email protected] or chat with us.