Elite Acoustics Engineering StompMIX X6 User manual

WHAT IS IN THE BOX
Your X6 package contains the following:
Elite Acoustics Engineering
StompMIX X6 - 6 Channels Digital Mixer
with Lithium Battery and Bluetooth®
Quick Guide Handbook
(1) StompMix X6 unit
(1) AC to 12VDC Power Supply Adapter
(1) Quick Start Guide & Registration Card
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Ing. and any use of such marks
by Elite Acoustics Designs, Inc is under license
NOTE: Due to continuous development and improvements of our products, features and specications are subject to
change without notice. All weights and measures are approximate.
For a copy of the complete User’s Manual, please visit: www.eliteacoustics.com

Aux Mix Level control Knob.
Main Mix Output Controls
Main Mix Volume Knob:
Mono: Changes Mix Main output to
Mono sound
Peak LED: RED indicate Signal Clip
Signal LED: GREEN indicate Signal
Present
Main Mix MUTE LED
Footswitch to MUTE MAIN MIX
output.
Foot Switch “A” “B” “MAIN MUTE”

Main
Pan
Ch1
Ch2 Ch3 Ch4
Ch56
Chorus
Reverb
Delay
System
Aux
Main
LCD FUNCTIONS
Menu Buttons with LCD:
Press any of the 6 menu buttons(black button located to the
left and right of LCD) or 5 encoders(blue knobs located around
LCD) to access and adjust features and settings. Most menus
have several pages of options, which are adjusted by turning the
corresponding encoder.
Main
Main
Mix
Ch1
Ch2 Ch3 Ch4
Ch56
Main
Pan
Ch1
Ch2 Ch3 Ch4
Ch56
“Main” Page 1: “Main Mix”
Adjust the level of each of the
5 channels.
“Main” Page 2: “Main Pan”
Adjust the stereo panning for each of
the 5 channels.
Aux
Mix
Ch1
Ch2 Ch3 Ch4
Ch56
Aux
Pan
Ch1
Ch2 Ch3 Ch4
Ch56
“Aux” : “Aux Mix” Adjust the level of each of the 5
channels sent to the Aux Outputs.
“Aux” : “Aux Pan” Adjust the panning between
“Aux Send 1” and “Aux Send 2” for each of the 5
channels.
Aux

System
“System” : “Input Levels”
Displays a bar graph for each
channel’s input level. Adjust the
channel’s “Gain” pot to set desired
level.
It is best to set your input signal level
to be under -12db to avoid clipping
the input circuit.
“System” : “Routing”
Assign “Pre” or “Post” fader i.e.,
“Main Mix” Channel 1 through
Channel 6, signals to the Aux Sends.
You can also select either “Main” mix
or “Aux” mix as the source for the
XLR outputs.
“System” : “Scenes”
Save and Recall up to 10 mixes i.e.,
scenes.
“Encoder Select” (press to enable):
“Ch 1 EQ”
Adjust the EQ settings for which ever
channel is selected.
“Encoder Select” (press to enable):
“Ch 1 Insert”
Adjust the Insert settings for the
selected channel (Ch.1-4). Note: this
includes Notch Filter and Frequency,
Gain and Threshold settings as well
as an independent Noise Gate.
“Encoder Select” (press to enable):
“Ch 5/6 Insert”
Adjust the Insert settings for Channel
5/6. Note: this includes Gain and
Threshold settings as well as an
independent Noise Gate.
Xlr Out
Eq Hi
LowM idF
Mid
LCut
“System” : “XLR out EQ”
Setting for EQ for the XLR outputs
when it is SET on “MAIN outputs”
Encoder Select
(Channel 1 to Channel 5/6)

“Reverb” : “Reverb Sends”
Adjust the Reverb level of each
of the 5 channels.
“Delay” : “Delay Param”
Adjust “Modulation,” “Feedback,”
“Time Offset,” “BPM” Delay Time, and
“Level” of the delay.
“Chorus” : “Chorus Sends”
Adjust the Chorus level of each of
the 5 channels.
“Chorus” : “Chorus Param”
Adjust the Depth of the Chorus for
each of the 5 channels.
“Reverb” : “Reverb Param”
Adjust the Decay and Tone of the
Reverb.
“Reverb” : “Delay Routes”
Assign a channel to the delay. Note
that this is an “insert” type effect and
is intended for a selectable single
channel. It precedes the Reverb and
Chorus effects.
Reverb
Reverb
Sends
Ch1
Ch2 Ch3 Ch4
Ch56
Delay
Delay
Param
Mod
Fbck TimX BPM
Lvl
1 120
Delay
Route
Chan
1
Chorus
Chorus
Sends
Ch1
Ch2 Ch3 Ch4
Ch56
BLUETOOTH® FUNCTION
• To turn ON/OFF Bluetooth® function
PRESS/HOLD down Bluetooth® button for approximately 5 seconds
Both LEDs will ash at the same time
• To pair device to the speaker system
Bluetooth® needs to be turned ON
QUICK TAP the Bluetooth® button once
Both Flashing LED: indicate Bluetooth®is ready to be paired
Flashing Blue LED only: indicate Bluetooth®is connected
BLUETOOTH® INPUTS CAN BE BE MIXED INTO MAIN AND AUX MIX BY PRESS-
ING THE SEND TO 5//6 SWITCH.

+48V LED: Indicates
Phantom Power is on
Midi IN and MIDI out
DC input Jack and Power Switch
“A” “B”
Footswithes
A and B are used to change Sences.
“MAIN MIX MUTE”
“FOOTSWITCHES”

Channel 3 and Channel 4
Gain: Gain level control
PAD: Fixed attenuation to reduce
input level
Line In: 1/4” TRS inputs
Mic In: XLR for Microphone Input
Gain: Gain level
control
PAD: Fixed
attenuation to reduce
input level
Line In: 1/4” TRS
input
Mic In: XLR for
Microphone Input
Source: Select Mic/
Line or Instrument
input
Instrument In [13]:
Channel 1 and 2

Main MIX Output:
XLR Left/Right
Output
Connect to Active
Speakers or
House PA system.
AUX MIX Output:
1/4” TS Left/Right
Output
Connect to an
Active Speaker for
stage Monitoring or
use these to send
to EFX unit. *use
Channel 5/6 as
Returns*
Channel 5/6
1/8” TRS jack input
Left (Mono): 1/4” balance TRS input
Right: 1/4” balance TRS input
Bluetooth® Signal can also be mixed into
Channel 5/6

SYSTEM SPECIFICATIONS
• System Architecture : Ultra high-speed high-capacity DSP with lossless A/D and D/A
conversion. Integrated Digital Mixer supports routing and seamless signal-level management
for ve fully congurable audio channels. Color Graphic LCD presents a highly intuitive GUI for
settings, save & recall, and MIDI functionality.
• Digital Effects and Controls: Channel Parametric EQ, Notch Filter, Compressor, Noise Gate,
Main and Aux panning, Reverb, Chorus, Delay, Real-Time Chan-Level Bar Graphs, Save & Recall
Programs.
• Analog Master controls: Master Volume, Mono Switch,
• Nominal output levels (1 kHz): Aux out: -10 dBu Main Output: +4dBu
• Stereo Inputs: 1/4” Left/Right input jacks
• Phantom Power: +48V
•
• Displays: Color Graphic LCD; signal, peak, sys power, phantom power, and batter level LEDs
• Connectors: CH1 & 2: Input jacks (mic XLR, 1/4” Line, 1/4” Instrument ), CH3/4: (mic XLR, 1/4”
Line), CH5/6: Left/Right stereo input (1/4” TRS) and 1/8” TRS jack, Aux Mix output (1/4” TS jack),
XLR Main Mix outputs, DC in jack
• Power Switch
• Power Supply: DC 12V 3A
• Built-in rechargeable Lithium Iron Phosphate battery with battery meter: approximately 6 to
6 hrs play timewith full charge
• Current Draw: 3000 mA
• Other features:
Playback from Bluetooth device.
Rechargeable Battery can be recharged from Car battery when using DC car
adaptor cord that is included
• Accessories: AC cord, AC adaptor, Owner’s manual
• Dimensions: 7.8”L x 9.8”W x 4.5”H
• Weight: 6 lbs
For more details, please visit: www.eliteacoustics.com or contract us via email.

WARRANTY (USA ONLY)
Contact the Distributor in your area for service and warranty info.
Elite Acoustics Engineering Inc. warrants this product to be free of defects in material and workmanship (excluding
battery) for a period of 1 year from the date of original retail purchase. Elite Acoustics Engineering Inc. warrants
the Speaker’s Battery for 90 days from the date of original retail purchase. This warranty is enforceable only by the
original retail purchaser. To be protected by this warranty, the purchaser must complete and return the enclosed
warranty card within 14 days of purchase. During the warranty period EAE shall, as its sole and absolute option,
either repair or replace, free of charge, any product that proves to be defective on inspection by EAE or its authorized
service representative. To obtain warranty service, contact Elite Acoustics Engineering Technical Support via email:
[email protected]. PRE-AUTHORIZATION MUST BE OBTAINED BEFORE SENDING ANY PRODUCT
TO AN ELITE ACOUSTIC ENGINEERING SERVICE CENTER. All inquires must be accompanied by a description
of the problem. All authorized returns must be sent to the EAE repair facility postage prepaid, insured and properly
packaged. EAE reserves the right to update any unit returned for repair. EAE reserves the right to change or
improve the design of the product at any time without prior notice. This warranty does not cover claims for damage
due to abuse, neglect, alteration, or attempted repair by unauthorized personnel and is limited to failures arising
during normal use that are due to defects in material or workmanship in the product. Any implied warranties,
including implied warranties of merchantability and tness for a particular purpose, are limited in duration to the
length of this limited warranty. Some states do not allow limitations on how long an implied warranty lasts, therefore
above limitation may not apply to you. In no event will EAE be liable for incidental, consequential, or other damages
resulting from the breach of any express or implied warranty, including among other things, damage to property,
damage based on inconvenience or on loss of use of the product, and, to the extent permitted by law, damages
for personal injury. Some states do not allow the exclusion of limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specic legal rights, and you
may also have other rights, which vary from state to state. This warranty only applies to products sold and used in
the United States of America. For warranty information in all other countries please refer to your local distributor.
©Elite Acoustics Engineering Inc.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS.
1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.