Elite Screens Tripod Tab-Tension CLR 2 Series User manual

Rev.083023JA wwww.elitescreens.com U00262 1
Tripod Tab-Tension CLR® 2 Series
Portable Ceiling Ambient Light Rejecting Projector Screen
For Ultra-short and Short-throw Projectors Only
USER’S GUIDE – M Type
V1.0
Thank you for choosing the Tripod Tab-Tension CLR® 2 projection screen! This tab-tensioned tripod pull-up
screen is best for rooms with minimal control of overhead room lighting. It utilizes our ISF Certified CLR® 2 front
projection ceiling ambient light rejecting material. It is precisely formulated to increase brightness, produce accurate
colors, and improve contrast. The CLR® 2 is best for family rooms, educational facilities, conference rooms, house
of worship or any applications in which incident light is a factor.
Compatible only with ultra-short and short-throw projectors.
In order for the CLR® 2 to maintain its projection qualities and optimum performance please refer to the list below
for proper maintenance and cleaning.
• Use a dry microfiber cloth to remove dust from the screen’s surface.
• When cleaning, use a damp microfiber cloth with warm water to remove any marks.
• Never rub or apply pressure when cleaning the surface.
• Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface.
• To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other
sharp or abrasive objects.
Please be sure to read the precautions and operating instructions carefully before operating the screen. Proper
maintenance and handling will ensure a longer lifespan for the product.
Tripod Screen Parts Identification
Vertical
Extension Bar
Support beam
Screen Material
End cap
Screen case
Top hook and
Screen Handle
Vertical locking
Carrying handle & Screen height
adjustment lock/release tab
Tripod junction
Tripod Support leg
Tripod drape skirt

Rev.083023JA wwww.elitescreens.com U00262 2
A. Tripod Screen Housing Installation and Setup:
Follow the steps below and Fig.1.
1. Place the tripod screen in an upright positionwith the legs toward the ground.
2. Deploy the tripod support legs by pushing down on the tripod junction.
3. Extend the legs as much as possible so they are stable and position them away from objects that may interfere
with their balance. DO NOT stand on unstable platforms to avoid an injury should the tripod screen collapse or
tip over.
4. Attach the screen housing to the tripod stand by inserting the back peg on the locking latch.
B. Preparing the tripod screen forprojection:
Follow the steps below and Fig. 2.
1. Pull the screen handle up vertically and hook the screen handle on the Top Hook.
2. Push/press the Vertical Locking Tab to unlock the current position of the Vertical Extension Bar and raise
it with another hand. Remain pushing on the button until you reach the desired height and let go until you hear
a click sound which indicates it is locked in place.
3. Push/press the Screen Height Adjustment Lock/Release located just above the Carrying Handle to raise
or lower the bottom of the screen. Once the desired height has been set, let goof the tab to lock the position in
place.
1
2
3
Fig.2
Press down the lock/release
tab on the locking latch.
Fig.1

Rev.083023JA wwww.elitescreens.com U00262 3
Tripod Skirt Installation
4. Unfold the tripod skirt in a clean area. Use the hook and loop fastener to attach it to the tripod case.
C. Collapsing thescreen:
Follow the steps below and Fig. 3.
1. Push/press the Screen Height Adjustment Lock/Release Tab to unlock and slowly
slide the handle up (NOT all the way) to slowly retract the screen into its case.
2. Press the Vertical Adjustment Lock/Release Tab to unlock and slowly bring the
extension bar down to lower the position of the screen’s tophook.
3. Unhook the screen material from the Top Hook and slowly retract the screen back
into the case.
4. Hold the Extension Bar and Push/press the Vertical Locking tab to unlock and
releasethe position of the extension bar. Bring the extension bar all the way down.
5. Close the tripod legs by pushing themin.
6. Pack the tripod screen in the carry bag included for protection and storage.
Note:
•To ensure the screen is stable, extend the tripod’s legs as muchas possible.
•Do not fold the screen or allow any sharp objects to touch the screen’s surface.
•Clean the screen surface often whenneeded.
•Careful use will extend the lifetime of thisproduct.
Note: It is very important to rememberto hold the extension bar first andthen
unlock the adjustment tab to prevent the extension bar from slamming and
causing injury or damaging the screen.
1
2
Fig.3

Rev.083023JA wwww.elitescreens.com U00262 4
Notice to Installer:
Material Tip: Proper Projector Placement for CLR®2
CORRECT
The CLR®2 is exclusively for tabletop/bottom mounted ultra and short throw projectors.
INCORRECT
Overhead placement or a standard projector will make the image very dark, on account of the screen’s absorbent layer
deflecting light that is not aligned with its reflective angle.
For more information, technical support or your local Elite Screens
contact, please visit www.elitescreens.com
2. Lens Throw Ratio 0.16 –1.2 X IMAGE WIDTH
1. Tabletop mounted UST and Short-throw projectors