Oben MBH-11 User manual

MBH-11
Dual-Action Mini Ballhead
You’reonsteadyground®

Thank you for choosing Oben
The Oben Dual Action Mini Ballhead is an ideal
accessory for most tabletop and mini tripods.
Lightweight yet strong and durable, this all-metal
ballhead boasts professional features that are more
often found in full-sized ballheads.
The MBH-11 is outfitted with an Arca-compatible
quick-release plate for rapid camera mounting and
swapping. Independent locking knobs oer 360°
panning and 90° tilt, making camera positioning
eortless and providing a secure platform for
cameras and lenses weighing up to 11 pounds.
INTRODUCTION

Visit our website at ObenSupports.com
for more Oben products.
!• Do not exceed the ballhead’s maximum
load capacity (see Specifications).
• Ensure that all appropriate locks are
engaged when necessary.
• This ballhead should be used only in
temperatures between -22°F and 140°F
(-30°C and 60°C).
• Remove the camera from the ballhead
during transport.
• To avoid damage, always support your
device or camera with one hand while
adjusting tilt and pan settings.
• All images are for illustrative purposes
only.
Maximum Load 11 lb. (5 kg)
Base Diameter 1.2 in. (30 mm)
Height 2.9 in. (7.4 cm)
Weight 5.35 oz. (152 g)
SPECIFICATIONS /WARNINGS
Warnings:

A
BC
F
D
H
G
E
J
I
01515 3030 4545 60
AQuick-releaseplate
B1/4-20mounting screw
CQuick-releaseknob
DVertical bubble level
EMainlocking knob
FReducerbushing
G3/8-16threadedsocket
HPanoramicbasewith 360° markings
IPanlocking knob
J90°notch
OVERVIEW

Screw the ballhead onto the
tripod’s mounting post.
Note: If the tripod has a 3/8-16
mounting post, remove the reducer
bushing from the ballhead’s
mounting socket.
Mountingthe Ballhead
OPERATION

The quick-release plate has a 1/4-
20 screw that fits most cameras.
1. Loosen the quick-release knob
by turning it counterclockwise,
and remove the quick-release
plate from the ballhead.
2. Screw the plate onto the bottom
of the camera.
3. Use the D-ring, a slotted
screwdriver, or a coin to tighten
the screw into the camera’s
socket.
Warning: Some manufacturers’
plates do not meet our specifications
and may not lock your equipment
securely in the Oben quick-release
clamp. Test any camera and lens
plates made by manufacturers other
than Oben to ensure compatibility
before use.
Mountingthe Quick-ReleasePlate
OPERATION

Make sure all knobs on the
ballhead are tightened, except for
the quick-release knob.
1. Turn the quick-release knob
counterclockwise until it stops.
2. Mount the camera to the
ballhead by sliding one edge
of the quick-release plate into
the clamp. Then lower the other
side until the quick-release
plate is lying flat in the quick-
release clamp.
Note: Make sure the mounting
screw’s D-ring is flush with the
bottom of the plate.
3. Turn the quick-release knob
clockwise to lock the plate.
Mountingthe Camera
OPERATION

The main locking knob locks
and unlocks the ballhead,
which allows you to change the
position of the camera.
Always use one hand to secure
the camera while adjusting the
ballhead, and make sure the lock
is engaged before letting go of
the camera.
Note: To adjust the tension in
a tight space, or if something
is blocking you from turning
the knob, pull the knob out,
reposition it so it can turn
without interference, and
release it. The knob will engage
and can be turned.
Use the 90° notch to quickly
switch between landscape and
portrait orientations.
MainLocking KnobOperation
OPERATION

The base of the ballhead can be
independently rotated 360°. Use
the degree markings on the base
of the ballhead to accurately set
up panoramic shots.
1. Twist the pan knob
counterclockwise to unlock the
base.
2. Rotate the base to the desired
position, and then lock the base
by turning the knob clockwise.
PanoramicBase
OPERATION

www.obensupports.com
Obenis a registeredtrademark ofthe GradusGroup.
©2020 GradusGroup LLC.All RightsReserved.
GG1