Emulex NJ01B-NT+ User manual

User Guide for
Emulex Printer Servers
Version 5.0
ER2054618-00A

Information contained in this document is believed to be accurate and reliable. However,
Emulex Corporation assumes no responsibility for its use nor for any infringements of patents
or other rights of third parties which may result from its use. Emulex Corporation reserves the
right to change product specifications at any time without notice.
The following trademarks of Emulex Corporation are used in this document:
Emulex
NETQue
NETQue Mate
NETQue Pro2
NETQue Token Ring
NETJet
rprint
enstall
The following are trademark acknowledgments:
UNIX is a trademark of AT&T Bell Laboratories
Novell and NetWare are trademarks of Novell Corporation
AppleTalk is a trademark of Apple Computer
Other brands and product names are trademarks of their respective companies.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense. Shielded cables must be used between this equipment and
attached peripheral devices. The reader is cautioned that changes or modifications made to
the equipment not expressly approved by Emulex could void the user’s authority to operate
this equipment.
The above statement applies to products marketed in the U.S.A.
This class A digital apparatus meets all requirements of the Canadian Interference - Causing
Equipment Regulations. Cet Appareil numerique de la classe A respecte toutes les exigences
du reglement sur le material brouilleur du Canada.
The above statement applies to products marketed in Canada.
Emulex Corporation
3535 Harbor Boulevard
Costa Mesa, CA 92626
Copyright © 1995 Emulex Corporation. All rights reserved worldwide. No part of this
document may be reproduced by any means nor translated to any electronic medium without
the written consent of Emulex Corporation.

Table of Contents
CHAPTER 1 INTRODUCTION
DOCUMENTATION .......................................................................................1-1
CHECK CONTENTS ......................................................................................1-2
CHECK MEDIA ............................................................................................1-3
CD-ROM ............................................................................................1-3
3.5 INCH DISKETTE..............................................................................1-3
HOW TO USE THIS GUIDE ...........................................................................1-4
USER GUIDE CONVENTIONS.................................................................1-4
WHAT IS A COMMAND? .......................................................................1-4
PROMPTS .............................................................................................1-4
Keywords ......................................................................................1-4
Variables .......................................................................................1-5
Options..........................................................................................1-5
Quotation Marks............................................................................1-5
NOS &PROTOCOL SUPPORT ...............................................................1-6
CHAPTER 2 PRINTER SERVER INSTALLATION
NETJET ......................................................................................................2-1
REFERENCE NUMBERS.........................................................................2-1
INSTALLATION.....................................................................................2-2
LAN CONNECTIONS &CABLING .........................................................2-3
Unshielded Twisted-Pair Connection............................................2-3
Thinwire BNC Connection............................................................2-4
PERIPHERAL CONNECTION...................................................................2-5
Serial Port......................................................................................2-5
POWER UP...........................................................................................2-6
DISPLAY LIGHTS (LEDS).....................................................................2-6
PRINT TEST PAGE ................................................................................2-7
PRINT CONFIGURATION PARAMETERS .................................................2-7
RESET TO FACTORY DEFAULTS............................................................2-8
FACTORY DEFAULT CONFIGURATION..................................................2-9
PRINTER SERVER SPECIFICATIONS.....................................................2-10
DECLARATION OF CONFORMITY ........................................................2-11
WHAT’S NEXT? .................................................................................2-12
Configure NOS............................................................................2-12

Table of Contents
ii
NETQUE PRO2 ........................................................................................ 2-13
REFERENCE NUMBERS ...................................................................... 2-13
LAN CONNECTIONS &CABLING ...................................................... 2-14
Unshielded Twisted-Pair Connection......................................... 2-14
Thinwire BNC Connection......................................................... 2-18
PERIPHERAL CONNECTIONS .............................................................. 2-16
Parallel Ports .............................................................................. 2-16
Serial Port................................................................................... 2-16
POWER UP......................................................................................... 2-17
DISPLAY LIGHTS (LEDS).................................................................. 2-18
PRINT TEST PAGE.............................................................................. 2-19
PRINT CONFIGURATION PARAMETERS .............................................. 2-20
Using Status Button.................................................................... 2-20
Using Software Command ......................................................... 2-20
RESET TO FACTORY DEFAULTS......................................................... 2-21
Reset Using Status Button.......................................................... 2-21
Reset Using Software Commands.............................................. 2-21
FACTORY DEFAULT CONFIGURATION ............................................... 2-22
PRINTER SERVER SPECIFICATIONS .................................................... 2-23
DECLARATION OF CONFORMITY ....................................................... 2-24
WHAT’S NEXT? ................................................................................ 2-25
Configure NOS........................................................................... 2-25
NETQUE.................................................................................................. 2-26
REFERENCE NUMBERS ...................................................................... 2-26
LAN CONNECTIONS &CABLING ...................................................... 2-27
Unshielded Twisted-Pair UTP Connection................................ 2-27
Thinwire BNC Connection......................................................... 2-28
PERIPHERAL CONNECTIONS .............................................................. 2-29
Parallel Port................................................................................ 2-29
Serial Port................................................................................... 2-29
POWER UP......................................................................................... 2-30
DISPLAY LIGHTS (LEDS).................................................................. 2-31
PRINT TEST PAGE.............................................................................. 2-32
PRINT CONFIGURATION PARAMETERS .............................................. 2-32
RESET TO FACTORY DEFAULTS......................................................... 2-33
FACTORY DEFAULT CONFIGURATION ............................................... 2-34
PRINTER SERVER SPECIFICATIONS .................................................... 2-35
OPTIONAL POWER SUPPLY SPECIFICATIONS ..................................... 2-36
DECLARATION OF CONFORMITY ....................................................... 2-37
WHAT’S NEXT? ................................................................................ 2-38
Configure NOS........................................................................... 2-38

Table of Contents
iii
NETQUE TOKEN RING..............................................................................2-39
REFERENCE NUMBERS.......................................................................2-39
SWITCH SETTINGS..............................................................................2-40
LAN CONNECTIONS &CABLING .......................................................2-41
Unshielded Twisted-Pair UTP Connection.................................2-41
Shielded Twisted-Pair STP Connection......................................2-42
PERIPHERAL CONNECTIONS ...............................................................2-42
Parallel Port.................................................................................2-42
Serial Port....................................................................................2-43
POWER UP.........................................................................................2-43
DISPLAY LIGHTS (LEDS)...................................................................2-45
PRINT TEST PAGE ..............................................................................2-46
PRINT CONFIGURATION PARAMETERS ...............................................2-46
RESET TO FACTORY DEFAULTS..........................................................2-47
Reset Using Switch Settings .......................................................2-47
Reset Using Software Command ................................................2-48
FACTORY DEFAULT CONFIGURATION................................................2-49
PRINTER SERVER SPECIFICATIONS.....................................................2-50
OPTIONAL POWER SUPPLY SPECIFICATIONS ......................................2-51
DECLARATION OF CONFORMITY ........................................................2-52
WHAT’S NEXT? .................................................................................2-53
Configure NOS............................................................................2-53
CHAPTER 3 NOVELL NETWARE
REQUIREMENTS...........................................................................................3-1
BINDERY MODE...................................................................................3-1
NDS MODE..........................................................................................3-1
BEFORE INSTALLATION...............................................................................3-2
CHOOSE PSERVER OR RPRINTER...........................................................3-2
CONFIGURE AS PSERVER -NETWARE 1.2 TO 3.12 ...................................3-3
CREATE THE PRINT QUEUE ..................................................................3-3
ADD THE PRINTER SERVER ..................................................................3-4
ADD THE PRINTER................................................................................3-4
SELECT THE PRINT QUEUE...................................................................3-4
RESTART THE PRINTER SERVER...........................................................3-5
CONFIGURE AS PSERVER -NETWARE 4.XX..............................................3-5
NDS MODE REQUIREMENTS................................................................3-6
Create the Print Queue ..................................................................3-6
Add the Printer Server...................................................................3-7
Add the Printer..............................................................................3-7
Select the Print Queue...................................................................3-7
Link Printer Server to Printer........................................................3-8
Restart the Printer Server ..............................................................3-8

Table of Contents
iv
BINDERY EMULATION MODE.............................................................. 3-9
Create the Print Queue ................................................................. 3-9
Add the Printer Server.................................................................. 3-9
Add the Printer........................................................................... 3-10
Select the Print Queue................................................................ 3-10
Restart the Printer Server ........................................................... 3-10
CONFIGURE AS RPRINTER..................................................................... 3-11
CREATE THE PRINT QUEUE ............................................................... 3-11
ADD THE REMOTE PRINTER .............................................................. 3-11
SELECT THE PRINT QUEUE................................................................ 3-12
RESTART THE PRINTER SERVER ........................................................ 3-13
286 Non-Dedicated Servers - VAP............................................ 3-13
386 Dedicated Servers - NLM.................................................... 3-13
Dedicated Printer Servers - 286 or 386...................................... 3-13
LOGGING INTO THE PRINTER SERVER....................................................... 3-14
REMOTE LOGIN................................................................................. 3-14
LOCAL LOGIN ................................................................................... 3-16
CONFIGURE SPECIFIC NETWARE PARAMETERS ....................................... 3-17
ADD NETWARE PASSWORD TO PRINTER SERVER ............................. 3-17
DEFINE THE PREFERRED NOVELL NETWARE FILE SERVER............... 3-18
DEFINE THE METHOD OF DISCOVERY (NETWARE 4.XX)................... 3-18
DEFINE THE NDS TREE ..................................................................... 3-19
DEFINE THE POSITION OF THE PSERVER -NDS MODE ....................... 3-19
WHAT’S NEXT?........................................................................................ 3-20
CONFIGURE NOS.............................................................................. 3-20
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .................................................... 3-20
CHAPTER 4 UNIX
REQUIREMENTS.......................................................................................... 4-1
BEFORE INSTALLATION.............................................................................. 4-2
AUTOMATIC INSTALLATION....................................................................... 4-2
CD ROM............................................................................................ 4-2
DISKETTE............................................................................................ 4-3
MANUAL INSTALLATION............................................................................ 4-4
ARP.................................................................................................... 4-4
Change IP Address....................................................................... 4-4
Assign IP Address........................................................................ 4-5
Assign Symbolic Name................................................................ 4-6
BOOTP................................................................................................ 4-7
DHCP................................................................................................. 4-8
RARP................................................................................................. 4-9

Table of Contents
v
CONFIGURE THE PRINT QUEUE ..........................................................4-10
Configure for BSD Hosts............................................................4-10
Configure a System V Host.........................................................4-13
LPD...................................................................................................4-16
Configure LPD on a BSD UNIX Host........................................4-16
Configure LPD for Non-UNIX Hosts.........................................4-18
LPSTAT............................................................................................4-19
CONFIGURE FOR SYSLOG SUPPORT ...........................................................4-19
LOGGING INTO THE PRINTER SERVER........................................................4-21
REMOTE LOGIN..................................................................................4-21
LOCAL LOGIN ....................................................................................4-23
WHAT’S NEXT? ........................................................................................4-24
CONFIGURE NOS...............................................................................4-24
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .....................................................4-24
CHAPTER 5 VAX/VMS DECNET
REQUIREMENTS...........................................................................................5-1
BEFORE INSTALLATION...............................................................................5-1
PRINTER QUEUES........................................................................................5-1
LOGGING INTO THE PRINTER SERVER..........................................................5-3
REMOTE LOGIN....................................................................................5-3
LOCAL LOGIN ......................................................................................5-4
WHAT’S NEXT? ..........................................................................................5-6
CONFIGURE NOS.................................................................................5-6
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .......................................................5-6
CHAPTER 6 APPLETALK
REQUIREMENTS...........................................................................................6-1
BEFORE INSTALLATION...............................................................................6-1
SELECT PRINTER.........................................................................................6-1
LOGGING INTO THE PRINTER SERVER..........................................................6-2
LOCAL LOGIN ......................................................................................6-3
ADVANCED APPLETALK PARAMETERS.......................................................6-4
NON BI-DIRECTIONAL PRINTERS.........................................................6-4
View Printer Fonts ........................................................................6-4
View Printer Server Fonts.............................................................6-5
Add Printer Server Fonts...............................................................6-5
Remove Printer Server Fonts ........................................................6-5
TAGGED BINARY COMMUNICATION PROTOCOL...................................6-6

Table of Contents
vi
WHAT’S NEXT?.......................................................................................... 6-7
CONFIGURE NOS................................................................................ 6-7
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR ...................................................... 6-7
CHAPTER 7 LAN MANAGER
REQUIREMENTS.......................................................................................... 7-1
PRINT MANAGER DISTRIBUTION FILES ...................................................... 7-1
BEFORE INSTALLATION.............................................................................. 7-2
INSTALLATION ........................................................................................... 7-4
ADD NEW PRINTERS .................................................................................. 7-4
TCP/IP PROTOCOL.............................................................................. 7-6
Advanced Options........................................................................ 7-8
NETBIOS PROTOCOL........................................................................... 7-9
Advanced Options...................................................................... 7-10
PRINTER TEST................................................................................... 7-11
CHANGE OR DELETE PRINTERS ................................................................ 7-11
DELETE PRINTER............................................................................... 7-12
CHANGE TCP/IP PRINTER’S PROPERTIES.......................................... 7-12
CHANGE NETBIOS PRINTER’S PROPERTIES ....................................... 7-13
OPTIONS MENU................................................................................. 7-14
TELRCF.................................................................................................. 7-15
CONFIGURE TELRCF ....................................................................... 7-15
USE TELRCF ................................................................................... 7-16
ENTER SCRIPTS................................................................................. 7-16
WHAT’S NEXT?........................................................................................ 7-18
CONFIGURE NOS.............................................................................. 7-18
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .................................................... 7-18
CHAPTER 8 LAN SERVER
REQUIREMENTS.......................................................................................... 8-1
PRINT MANAGER DISTRIBUTION FILES ...................................................... 8-1
BEFORE INSTALLATION.............................................................................. 8-3
LAN SERVER PRIOR TO 4.0................................................................. 8-3
LAN SERVER 4.0................................................................................ 8-4
INSTALLATION ........................................................................................... 8-4
ADD NEW PRINTERS .................................................................................. 8-5
TCP/IP PROTOCOL.............................................................................. 8-6
Advanced Options........................................................................ 8-8
NETBIOS PROTOCOL........................................................................... 8-9
Advanced Options...................................................................... 8-11

Table of Contents
vii
TEST PRINTER....................................................................................8-12
CHANGE OR DELETE PRINTERS .................................................................8-13
CHANGE TCP/IP PRINTER’S PROPERTIES...........................................8-13
CHANGE NETBIOS PRINTER’S PROPERTIES........................................8-14
DELETE PRINTER ...............................................................................8-14
OPTIONS MENU..................................................................................8-15
TELRCF...................................................................................................8-15
CONFIGURE TELRCF........................................................................8-16
USE TELRCF....................................................................................8-17
ENTER SCRIPTS..................................................................................8-17
WHAT’S NEXT? ........................................................................................8-19
CONFIGURE NOS...............................................................................8-19
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .....................................................8-19
CHAPTER 9 WINDOWS NT
REQUIREMENTS...........................................................................................9-1
BEFORE INSTALLATION...............................................................................9-1
INSTALLATION ............................................................................................9-1
CREATE A TCP/IP PRINTER ........................................................................9-4
UNIQUE PRINTER QUEUE NAMES.........................................................9-7
PRINTING TO WINDOWS NT FROM UNIX .................................................9-10
LOGGING INTO THE PRINTER SERVER........................................................9-11
REMOTE LOGIN..................................................................................9-11
LOCAL LOGIN ....................................................................................9-13
WHAT’S NEXT? ........................................................................................9-14
CONFIGURE NOS...............................................................................9-14
MANAGE WITH EMULEX NET WIZARD
PRINTER SERVER ADMINISTRATOR .....................................................9-14
CHAPTER 10 CONTACTING EMULEX
TECHNICAL ASSISTANCE...........................................................................10-1
PRIOR TO YOUR CALL........................................................................10-1
PLACING THE CALL............................................................................10-2
Domestic .....................................................................................10-2
European .....................................................................................10-2
24 -HOUR SUPPORT...........................................................................10-3
PRODUCT SERVICE....................................................................................10-3
BULLETIN BOARD SYSTEM .......................................................................10-3
INTERNET..................................................................................................10-5
EMUFAX ...................................................................................................10-6

Table of Contents
viii APPENDIX
CONNECTOR PINOUTS ...........A-ERROR! BOOKMARK NOT DEFINED.
ETHERNET UTP CONNECTOR PINOUT -RJ-45 ......................................A-
Error! Bookmark not defined.
TOKEN RING UTP PINOUT -RJ-45....A-Error! Bookmark not defined.
TOKEN RING STP PINOUT -FEMALE-DB9A-Error! Bookmark not defined.
SERIAL CONNECTOR PINOUT -MALE DB9 (DTE) ................................A-
Error! Bookmark not defined.
CONSOLE CONNECTOR PINOUT -RJ12 (DTE).......................................A-
Error! Bookmark not defined.
PARALLEL CONNECTOR PINOUT .......A-Error! Bookmark not defined.
ACRONYMS ................................................................................................A-7
GLOSSARY .................................................................................................A-8

Introduction
Chapter 1
Thank you for purchasing an Emulex network product. You have joined the
Emulex family of users who have found that our products greatly facilitate
computer communication and the management of network resources. We
value a strong relationship with our customers and seek to serve your needs
in the years to come.
Emulex Corporation ( HQ ) ( 714 ) 662-5600
PreSales Support ( 714 ) 513-8053
Technical Support ( 714 ) 513-8270
New customers will find that the printer server can be used immediately
since the default printer server parameters are applicable to most networks.
Documentation
The documentation provides comprehensive guides detailing installation,
configuration and management of Emulex printer servers. This material is
either on CD-ROM or in hardcopy. Listed below are the guides and a brief
description of what they will help you accomplish.
•Printer Server User Guide
−Install printer server.
−Configure network operating system.
•Command Reference Guide
−Understand proper syntax and use of printer server commands.
•Software Upgrade Guide
−Upgrade Emulex printer server software.
•Emulex NET wizard printer server administrator User Guide
−Install Emulex NET wizard printer server administrator.

1-2 Chapter 1
−Configure printer servers - For example, add printers, assign trap
hosts, assign workgroups, upgrade printer server software, perform
memory image dumps, enable protocols, etc.
−Configure for NetWare - For example, choose PSERVER or
RPRINTER, choose frame type, perform rediscovery, create,
configure and assign print queues, etc.
Check Contents
•Emulex printer server
•Manuals: Manuals are available on the CD-ROM or in hardcopy.
−Printer Server User Guide
−Command Reference Guide
−Software Upgrade Guide
−Emulex NET wizard printer server administrator User Guide
•Warranty Registration Card
•Software utilities: CD-ROM or Diskette
•Power Supply
−NETJet - No power supply required
−NETQue and NETQue Token Ring - Power supply module
(transformer)
−NETQue Pro2 - AC power cord and selection guide
If any items are missing, please contact your local Emulex distributor.

Introduction 1-3
Check Media
You have received software either on CD-ROM or diskette. Depending upon
the media enclosed, verify the contents:
CD-ROM
•On-Line Manuals
−Printer Server User Guide
−Command Reference Guide
−Software Upgrade Guide
−Emulex NET wizard printer server administrator User Guide
•Printer server software files:
Flash Update Utilities
UNIX Utilities (tar format)
TES Utilities for Netware (DOS format)
Microsoft OS/2 LAN Man Printer Manager (DOS format)
IBM OS/2 LAN Server Printer Manager (DOS format)
•Emulex NET wizard printer server administrator software files
3.5 Inch Diskette
•Printer server software files:
Flash Update Utilities
UNIX Utilities (tar format)
TES Utilities for Netware (DOS format)
Microsoft OS/2 LANMan Printer Manager (DOS format)
IBM OS/2 LANServer Printer Manager (DOS format)
•Emulex NET wizard printer server administrator software files

1-4 Chapter 1
How to Use This Guide
This guide is designed to assist in the installation of your Emulex printer
server. The material contained in the guide is directed toward the network
administrator or the one responsible for a company’s computer network
needs.
User Guide Conventions
You will notice text boxes labeled NOTE or CAUTION.
•Notes provide additional information.
•Caution statements provide warnings to prevent harm to people or
equipment.
CAUTION:: Observe electrostatic discharge (ESD)
procedures during installation.
What is a Command?
A prompt, followed by a keyword and one or more variables, options or
quotation marks make up a command. The following explanation will
demonstrate command formatting.
Prompts
A prompt consists of the word Server followed by one or two greater than
symbols (>). One (>) indicates nonprivileged status and two (>>) signify
privileged or supervisor status. The two prompts are shown below:
Server > (nonprivileged users)
Server >> (privileged users)
Nonprivledged users have read only privileges. Privileged or supervisor users
have all read and write privileges.
Keywords
Keywords are enclosed in brackets and separated by vertical lines. The
user must enter a keyword to perform an action.
>Server >>[set|define|change]

Introduction 1-5
Variables
Variables are used as in mathematics: they represent a quantity, device name,
address or other entity. They are shown in bold italic type.
>Server>>[set|define|change]server dhcp nm
n a variable
m a variable
Options
Options are used to customize a command. When available, the user should
always use options. They are italicized and enclosed in brackets.
>Server>>[set|define|change]server dhcp nm
[temp][default]
temp an optional entry
default an optional entry
Quotation Marks
When case-sensitive information is required, it must begin and end with
quotation marks. Font names are case-sensitive and must appear in quotes
within command lines. The example below illustrates the use of a font name
within a command line.
>Server>> change port 1 fonts add “Courier-Bold
Helvetica-Italics”

1-6 Chapter 1
NOS & Protocol Support
With the recent release of printer server software version 5.0, we have
expanded the protocols supported by our existing line of Emulex printer
servers. Emulex printer servers can currently be used with these network
operating systems and protocols:
NETQue NQPro2 NETJet NQToken
Novell Netware
TES, IPX/SPX 
UNIX
TCP/IP, LPD, Telnet 
Apple
EtherTalk 
Apple
TokenTalk

VAX/VMS
DECnet LAT 
Microsoft OS/2
LAN Manager
TCP/IP, LPD, NetBios 
IBM OS/2
LAN Server
TCP/IP, LPD, NetBios 
Windows NT
TCP/IP, LPD 

Printer Server
Installation
Chapter 2
NETJET ................................................................................................................... 2-1
REFERENCE NUMBERS.................................................................................................. 2-1
INSTALLATION.............................................................................................................. 2-2
LAN CONNECTIONS &CABLING .................................................................................. 2-3
UNSHIELDED TWISTED-PAIR CONNECTION.......................................................... 2-3
THINWIRE BNC CONNECTION.............................................................................. 2-4
PERIPHERAL CONNECTION............................................................................................ 2-5
SERIAL PORT........................................................................................................ 2-5
POWER UP.................................................................................................................... 2-6
DISPLAY LIGHTS (LEDS).............................................................................................. 2-6
PRINT TEST PAGE ......................................................................................................... 2-7
PRINT CONFIGURATION PARAMETERS .......................................................................... 2-7
RESET TO FACTORY DEFAULTS .................................................................................... 2-8
FACTORY DEFAULT CONFIGURATION........................................................................... 2-9
PRINTER SERVER SPECIFICATIONS.............................................................................. 2-10
DECLARATION OF CONFORMITY................................................................................. 2-11
WHAT’S NEXT? .......................................................................................................... 2-12
CONFIGURE NOS ............................................................................................... 2-12
NETQUE PRO2................................................................................................................. 2-13
REFERENCE NUMBERS................................................................................................ 2-13
LAN CONNECTIONS &CABLING ................................................................................ 2-14
UNSHIELDED TWISTED-PAIR CONNECTION........................................................ 2-14
THINWIRE BNC CONNECTION............................................................................ 2-15
PERIPHERAL CONNECTIONS........................................................................................ 2-16
PARALLEL PORTS............................................................................................... 2-16
SERIAL PORT...................................................................................................... 2-16
POWER UP.................................................................................................................. 2-17
DISPLAY LIGHTS (LEDS)............................................................................................ 2-18

ii Chapter 2
PRINT TEST PAGE........................................................................................................2-19
PRINT CONFIGURATION PARAMETERS.........................................................................2-20
USING STATUS BUTTON......................................................................................2-20
USING SOFTWARE COMMAND.............................................................................2-20
RESET TO FACTORY DEFAULTS ...................................................................................2-21
RESET USING STATUS BUTTON...........................................................................2-21
RESET USING SOFTWARE COMMANDS................................................................2-21
FACTORY DEFAULT CONFIGURATION..........................................................................2-22
PRINTER SERVER SPECIFICATIONS...............................................................................2-23
DECLARATION OF CONFORMITY..................................................................................2-24
WHAT’S NEXT?...........................................................................................................2-25
CONFIGURE NOS................................................................................................2-25
NETQUE .................................................................................................................2-26
REFERENCE NUMBERS.................................................................................................2-26
LAN CONNECTIONS &CABLING.................................................................................2-27
UNSHIELDED TWISTED-PAIR UTP CONNECTION ................................................2-27
THINWIRE BNC CONNECTION ............................................................................2-28
PERIPHERAL CONNECTIONS.........................................................................................2-29
PARALLEL PORT .................................................................................................2-29
SERIAL PORT.......................................................................................................2-29
POWER UP...................................................................................................................2-30
DISPLAY LIGHTS (LEDS).............................................................................................2-31
PRINT TEST PAGE........................................................................................................2-32
PRINT CONFIGURATION PARAMETERS.........................................................................2-32
RESET TO FACTORY DEFAULTS ...................................................................................2-33
FACTORY DEFAULT CONFIGURATION..........................................................................2-34
PRINTER SERVER SPECIFICATIONS...............................................................................2-35
OPTIONAL POWER SUPPLY SPECIFICATIONS................................................................2-36
DECLARATION OF CONFORMITY..................................................................................2-37
WHAT’S NEXT?...........................................................................................................2-38
CONFIGURE NOS................................................................................................2-38

Printer Server Installation iii
NETQUE TOKEN RING.................................................................................................. 2-39
REFERENCE NUMBERS................................................................................................ 2-39
SWITCH SETTINGS ...................................................................................................... 2-40
LAN CONNECTIONS &CABLING ................................................................................ 2-41
UNSHIELDED TWISTED-PAIR UTP CONNECTION................................................ 2-41
SHIELDED TWISTED-PAIR STP CONNECTION..................................................... 2-42
PERIPHERAL CONNECTIONS........................................................................................ 2-42
PARALLEL PORT................................................................................................. 2-42
SERIAL PORT...................................................................................................... 2-43
POWER UP.................................................................................................................. 2-43
DISPLAY LIGHTS (LEDS)............................................................................................ 2-45
PRINT TEST PAGE ....................................................................................................... 2-46
PRINT CONFIGURATION PARAMETERS ........................................................................ 2-46
RESET TO FACTORY DEFAULTS .................................................................................. 2-47
RESET USING SWITCH SETTINGS........................................................................ 2-47
RESET USING SOFTWARE COMMAND................................................................. 2-48
FACTORY DEFAULT CONFIGURATION......................................................................... 2-49
PRINTER SERVER SPECIFICATIONS.............................................................................. 2-50
OPTIONAL POWER SUPPLY SPECIFICATIONS ............................................................... 2-51
DECLARATION OF CONFORMITY................................................................................. 2-52
WHAT’S NEXT? .......................................................................................................... 2-53
CONFIGURE NOS ............................................................................................... 2-53