ENA Micro 9 One Touch User manual

pt
es
nl
it
fr
ru
en
de
The Instructions for Use has been awarded the seal of
approval by the independent German Technical
Inspection Agency, TÜV SÜD, due to its easy-to-
understand style, its thoroughness and coverage of
safety aspects.
micro 9
InstructionsforuseforENAMicro9OneTouch

30
Table of contents
Your ENA Micro 9 One Touch
Control elements 32
Important information 34
Proper use...............................................................................................................................................................34
For your safety.......................................................................................................................................................34
1 Preparing and using for the first time 35
JURA on the Internet.............................................................................................................................................35
3-colour plain text display....................................................................................................................................35
Setting up the machine........................................................................................................................................35
Filling the bean container....................................................................................................................................35
First-time use..........................................................................................................................................................35
First-time use with filter cartridge activation...................................................................................................36
First-time use without filter cartridge activation.............................................................................................37
Determining the water hardness........................................................................................................................37
Adjusting the grinder............................................................................................................................................37
Filling the water tank............................................................................................................................................38
2 Preparation 38
Espresso, coffee......................................................................................................................................................38
Latte macchiato, cappuccino...............................................................................................................................38
Permanently setting the amount of water for the cup size...........................................................................39
Ground coffee.........................................................................................................................................................39
Hot water................................................................................................................................................................40
3 Daily operation 40
Switching on the machine..................................................................................................................................40
Daily maintenance................................................................................................................................................40
Switching off the machine...................................................................................................................................41
4 Permanent settings in programming mode 41
Products..................................................................................................................................................................41
Setting the water hardness..................................................................................................................................42
Energy-saving mode.............................................................................................................................................42
Automatic switch-off.............................................................................................................................................43
Rinses.......................................................................................................................................................................43
Unit for amount of water....................................................................................................................................44
Language................................................................................................................................................................44
5 Maintenance 44
Rinsing the machine............................................................................................................................................44
Rinsing the milk system......................................................................................................................................45
Cleaning the milk system.................................................................................................................................... 45
Dismantling and rinsing the dual spout...........................................................................................................46
Inserting and activating the filter......................................................................................................................46
Changing the filter.................................................................................................................................................47
Cleaning the machine..........................................................................................................................................48

31
pt
es
nl
it
fr
ru
en
de
Table of contents
Symbol description
Warnings
JWARNING
JCAUTION Always take note of any information marked with the words CAUTION or WARNING
and a warning sign. The signal word WARNING draws your attention to potential
serious injury, and the signal word CAUTION to potential minor injury.
CAUTION CAUTION draws your attention to potential damage to the machine.
Symbols used
TPrompt to take action. This symbol means that you are being prompted to perform
some action.
EInformation and tips to make it even easier to use your ENA.
ESPRESSO Display
Descaling the machine .......................................................................................................................................48
Descaling the water tank.....................................................................................................................................49
Cleaning the bean container..............................................................................................................................50
6 Display messages 51
7 Troubleshooting 52
8 Transport and environmentally friendly disposal 53
Transport / Emptying the system.......................................................................................................................53
Disposal...................................................................................................................................................................53
9 Technical data 53
10 Index 54
11 JURA contact details / Legal information 56

32
Control elements
Control elements
micro 9









1 Water tank
2 Mains cable (back of the machine)
3 Milk pipe
4 Coffee grounds container
5 Drip tray
6 Bean container with aroma preservation
cover
7 Hot-water spout
8 Height-adjustable dual spout
9 Cup grille

33
Control elements
pt
es
nl
it
fr
ru
en
de














1 Cover for powder chute for ground coffee
2 Powder chute for ground coffee
3 Display
4 cMaintenance button
5 /Cappuccino button
6 (Latte Macchiato button
7 Rotary Switch status display
8 Cover cap for grinder adjustment switch
9 Grinder adjustment switch
10 gRotary Switch
11 mHot Water button
12 <Espresso button
13 QOn/Off button
14 >Coffee button

34
Important information
Important information
Proper use
The machine is designed and intended for private
domestic use. It should only be used for coffee
preparation and to heat milk and water. Use for
any other purpose will be deemed improper. JURA
Elektroapparate AG cannot accept any responsibil-
ity for the consequences of improper use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty
service is not applicable for damage or defects
caused by non-compliance with the instructions
for use. Keep these instructions for use close to the
machine and pass them on to the next user.
For your safety
Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
UNever use a machine which is damaged or has
a defective mains cable.
UIn the event of signs of damage, for example
if there is a smell of burning, unplug the
machine immediately from the mains supply
and contact JURA service.
UIf the mains cable of this machine is damaged,
it must be repaired either directly by JURA or
by an authorised JURA service centre.
UMake sure that the ENA and the mains cable
are not located close to hot surfaces.
UBe careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
UNever open and repair the machine yourself.
Do not modify the machine in any way that is
not described in these instructions for use.
The machine contains live parts. If opened,
there is a danger of potentially fatal injury.
Repairs may only be carried out by authorised
JURA service centres, using original spare parts
and accessories.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
UNever allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
UProtect the ENA from environmental influ-
ences such as rain, frost and direct sunlight.
UDo not immerse the ENA, mains cable or
connections in water.
UDo not put the ENA or any individual parts in
the dishwasher.
USwitch your ENA off before cleaning work with
the On/Off button. Always wipe the ENA with a
damp cloth rather than a wet one, and protect
it from prolonged exposure to water splash.
UOnly connect the machine to the mains
voltage in accordance with the information on
the rating plate. The rating plate is located on
the underside of your ENA. Further technical
data is provided in these instructions for use
(see Chapter 9 ‘Technical data’).
UPlease only use original JURA maintenance
products. Use of products that are not
explicitly recommended by JURA could
damage the ENA.
UDo not use any coffee beans treated with
additives or caramelised coffee beans.
UOnly fill the water tank with fresh, cold water.
UDo not fill the bean container with water.
USwitch the machine off with the On/Off button
if you are going to be absent for a longer
period of time and remove the mains plug
from the power socket.
People, including children, who
Udo not have the physical, sensory or mental
capabilities to use the machine safely or
Uare inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it
correctly.

35
1 Preparing and using for the first time
pt
es
nl
it
fr
ru
en
de
Safety when handling the CLARIS Blue filter
cartridge:
UFilter cartridges should be kept out of the
reach of children.
UStore filter cartridges in a dry place in the
sealed packaging.
UProtect cartridges from heat and direct
sunlight.
UDo not use damaged filter cartridges.
UDo not open filter cartridges.
1 Preparing and using for the
first time
This chapter provides you with the information
you need to use your ENA without any problems.
You will prepare your ENA step-by-step to enjoy
your first perfect cup of coffee.
JURA on the Internet
Visit us on the Internet.
On the JURA website (www.jura.com) you will find
interesting and up-to-date information on your
ENA and on every aspect of coffee.
3-colour plain text display
Your ENA features a 3-colour plain text display. The
colours of the display texts have the following
meanings:
UGreen: The ENA is ready for use.
URed: The ENA is prompting you to perform
some action.
UYellow: You are in programming mode.
Setting up the machine
When setting up your ENA, please note the
following:
UPlace the machine on a horizontal surface that
is not sensitive to water.
UChoose a spot for your ENA which protects the
machine against overheating. Ensure that the
ventilation slots are not covered.
Filling the bean container
CAUTION
Coffee beans which have been treated with
additives (e.g. sugar), ground coffee or freeze-dried
coffee will damage the grinder.
TOnly use untreated coffee beans to fill the
bean container.
TRemove the aroma preservation cover of the
bean container.
TRemove any dirt or foreign objects from
inside the bean container.
TFill the bean container with coffee beans.
TClose the bean container.
First-time use
When using the machine for the first time, you can
choose whether you want to operate the ENA with
or without the CLARIS Blue filter cartridge. If the
water hardness is 10° dH or more, we recommend
using the filter cartridge. If you do not know the
hardness of your water, you can find this out first
(see Chapter 1 ‘Preparing and using for the first
time – Determining the water hardness’).
EThe On/Off button also acts as a power
switch. When the ENA is switched off, the
machine does not consume standby energy.
JWARNING
If the machine is operated with a defective mains
cable, there is a danger of potentially fatal electric
shock.
TNever use a machine which is damaged or
has a defective mains cable.

36
1 Preparing and using for the first time
Precondition: Bean container is filled.
TInsert the mains plug into a power socket.
QTPress the On/Off button to switch the
machine on.
SPRACHE DEUTSCH
gTTurn the Rotary Switch until the required
language is displayed, for example
LANGUAGE ENGLISH.
kTPress the Rotary Switch to confirm the
language setting.
OK, the language is set.
FILTERp / YESp
ENow decide whether you want to operate
your ENA with or without a CLARIS Blue
filter cartridge.
First-time use with filter cartridge
activation
kTPress the Rotary Switch.
OK
INSERT FILTER
TRemove the water tank.
TOpen the filter holder.
TInsert the filter cartridge into the water tank,
exerting slight pressure.
TClose the filter holder. It will click into place
audibly.
EAfter two months, the filter will cease to
work. Set the date on the date plate on the
filter holder in the water tank.
TFill the water tank with fresh, cold water and
reinsert it.
TPlace a receptacle (at least 500 ml) under the
hot-water and dual spout.
kTPress the Rotary Switch.
FILTER RINSING, water flows out of
the hot-water spout.
EYou can interrupt rinsing of the filter at any
time by pressing any button. Press the
Maintenance button c, to continue with
rinsing of the filter.
EThe water may be slightly discoloured. This
is not harmful to health and does not affect
the taste.
Rinsing of the filter stops automatically.
SYSTEM FILLING, water flows out of
the dual spout.
HEATING
RINSING, the system rinses itself. The
operation stops automatically.
READY
micro 9

37
1 Preparing and using for the first time
pt
es
nl
it
fr
ru
en
de
First-time use without filter cartridge
activation
gTTurn the Rotary Switch until
FILTER- / NO- is displayed.
kTPress the Rotary Switch.
OK
16°dH
gTTurn the Rotary Switch to change the water
hardness setting, e.g. to 25°dH.
kTPress the Rotary Switch.
OK
FILL WATER TANK
TRemove the water tank.
TFill the water tank with fresh, cold water and
reinsert it.
PRESS RINSE
TPlace a receptacle under the dual spout.
cTPress the Maintenance button.
SYSTEM FILLING, the system fills up
with water.
HEATING
RINSING, the system rinses itself. The
operation stops automatically.
READY
Determining the water hardness
You can find out what the water hardness is by
using the Aquadur® test strip supplied as standard.
THold the test strip briefly (for one second)
under running water.
TShake off the water.
TWait for about one minute.
TYou will then be able to read the degree of
water hardness from the discolouration of
the Aquadur® test strip and the description
on the packaging.
The water hardness can now be adjusted.
Adjusting the grinder
You can adjust the grinder on a continuous scale to
suit the degree of roast of your coffee.
CAUTION
If you adjust the consistency of grind when the
grinder is not operating, the grinder adjustment
switch could be damaged.
TOnly adjust the consistency of grind when
the grinder is running.
The consistency of grind setting is correct if the
coffee flows regularly from the dual spout. In
addition a fine, thick crema forms.
Example: Change the consistency of grind during
the preparation of an espresso.
TPlace a cup under the dual spout.
TOpen the cover cap of the grinder adjust-
ment switch.

38
2 Preparation
<TPress the Espresso button to start prepara-
tion.
TTurn the grinder adjustment switch to the
desired position while the grinder is
running.
The preset amount of water flows into the
cup. Preparation stops automatically.
READY
Filling the water tank
Daily maintenance of the machine and hygiene
when handling milk, coffee and water are key to a
perfect coffee result in the cup every time. You
should therefore change the water daily.
CAUTION
Milk, sparkling mineral water or other liquids can
damage the water tank or the machine.
TOnly fill the water tank with fresh, cold water.
TRemove the water tank and rinse with cold
water.
TFill the water tank with fresh, cold water and
reinsert it.
2 Preparation
EYou can interrupt preparation at any time
while a speciality coffee, speciality coffee
with milk or hot water is being prepared.
Just press any button.
EBefore and during the grinding operation
you can select the coffee strength of
espresso <, coffee >, cappuccino /and
latte macchiato (: NORMAL, STRONG.
EDuring preparation, you can change the
preset amounts (e.g. amount of milk foam
or water) by turning the Rotary Switch g.
EYou can follow the current status of
preparation on the progress bar.
Coffee tastes best served hot. A cold porcelain cup
cools the beverage – and impairs the taste. We
therefore recommend prewarming the cups. The
full coffee aroma can develop only in prewarmed
cups. You can purchase a JURA cup warmer from
your specialised dealer.
You can make permanent settings for all products
in programming mode (see Chapter 4 ‘Permanent
settings in programming mode – Products’).
Espresso, coffee
Preparation of espresso<and coffee >follows
this model.
Example: Proceed as follows to prepare one coffee.
Precondition: READY is displayed.
TPlace a cup under the dual spout.
>TPress the Coffee button to start preparation.
COFFEE, the preset amount of water
flows into the cup.
Preparation stops automatically.
READY
Latte macchiato, cappuccino
Your ENA can prepare a latte macchiato or
cappuccino at the touch of a button. There is no
need to move the glass or cup.
Preparationoflattemacchiato(andcappuccino/
follows this model.
Example: Proceed as follows to prepare one latte
macchiato.
Precondition: READY is displayed.
TPlace a glass under the dual spout.
TRemove the protective cover of the dual
spout.

39
2 Preparation
pt
es
nl
it
fr
ru
en
de
TConnect the milk pipe to the dual spout.
TImmerse the other end of the milk pipe in a
receptacle with milk (figure: optional JURA
0.4 litre stainless steel vacuum milk
container).
EEnsure that the filling height of the milk is
no higher than the milk pipe connection on
the dual spout.
(TPress the Latte Macchiato button.
LATTE MAC., the milk foam is prepared.
Preparation stops automatically when the
preset amount of milk is reached.
PAUSE
EThere is a short interval while the hot milk
separates from the milk foam. This allows
the typical layers of a latte macchiato to
form. You can choose the length of this
interval in programming mode (see
Chapter 4 ‘Permanent settings in program-
ming mode – Products’).
LATTE MAC., coffee preparation starts.
The preset amount of water flows into the
glass.
Preparation stops automatically.
READY
micro 9
micro 9
Permanently setting the amount of water
for the cup size
It is easy to make permanent settings for the
amount of water for all speciality coffees and hot
water according to the cup size. Adjust the amount
once as shown in the following example. Every
time you prepare a drink in the future, this amount
of water will be dispensed.
Example: Permanently adjust the amount of
water for one coffee to the cup size.
Precondition: READY is displayed. Milk is
connected to the dual spout.
TPlace a cup under the dual spout.
/TPress and hold the Cappuccino button.
CAPPUCCINO
/TContinue to hold the Cappuccino button
down until ENOUGH MILK? appears.
/TRelease the Cappuccino button.
The milk foam is prepared.
TPress any button as soon as there is
sufficient milk foam in the cup.
OK
ENOUGH COFFEE?, the coffee flows
into the cup.
TPress any button as soon as there is
sufficient coffee in the cup.
OK, CAPPUCCINO, the set amounts for
one cappuccino are permanently stored.
READY
EYou can alter this setting at any time by
repeating the above procedure.
Ground coffee
You can choose to use a second coffee variety, for
example decaffeinated coffee, with the powder
chute for ground coffee.
ENever add more than one level measuring
spoon of ground coffee.
EUse ground coffee which is not ground too
finely. Very fine coffee can block up the
system so that the coffee only comes out in
drips.

40
3 Daily operation
EIf you did not fill the machine with a
sufficient amount of ground coffee, NOT
ENOUGH POWDER is displayed and the
ENA stops the operation.
EThe desired speciality coffee must be
prepared within approximately one minute
after filling with the ground coffee.
Otherwise the ENA stops the operation and
is once more ready for use.
The preparation of coffee, espresso, cappuccino
and latte macchiato with ground coffee follows
this model.
Example: Prepare a cup of coffee using ground
coffee.
Precondition: READY is displayed.
TPlace a cup under the dual spout.
TOpen the powder chute for ground coffee.
FILL POWDER
TPlace the filler funnel for ground coffee on
the powder chute.
TPlace one level measuring spoon of ground
coffee into the filler funnel.
TClose the powder chute for ground coffee.
SELECT BUTTON
>TPress the Coffee button to start preparation.
COFFEE, the preset amount of water
flows into the cup.
Preparation stops automatically.
READY
Hot water
JCAUTION
There is a danger of scalding from hot water
splashes.
TAvoid direct contact with the skin.
Precondition: READY is displayed.
TPlace a cup under the hot-water spout.
mTPress the Hot Water button.
WATER, the preset amount of water flows
into the cup.
Preparation stops automatically.
READY
3 Daily operation
Switching on the machine
Daily maintenance of the machine and hygiene
when handling milk, coffee and water are key
to a perfect coffee result in the cup every time.
You should therefore change the water daily.
TPlace a receptacle under the dual spout.
QTPress the On/Off button to switch the
machine on.
HEATING
RINSING, the system rinses itself.
The operation stops automatically.
READY
Daily maintenance
To ensure that you get many years of reliable
service out of your ENA and to guarantee the
optimum coffee quality, the machine requires
daily maintenance.
TRemove the drip tray.
TEmpty the coffee grounds container and
drip tray and rinse with warm water.
TReinsert the coffee grounds container and
the drip tray.
TRinse the water tank with clean water.

41
4 Permanent settings in programming mode
pt
es
nl
it
fr
ru
en
de
TDismantle and rinse the dual spout (see
Chapter 5 ‘Maintenance – Dismantling and
rinsing the dual spout’).
TWipe the surface of the machine with a
clean, soft, damp cloth (e.g. microfibre
cloth).
EIn the interests of hygiene, we recommend
changing the milk pipe on a regular basis
(approx. every 6 months). Replacement
pipes are available from specialised dealers.
Switching off the machine
When the ENA is switched off, the system is
automatically rinsed if a speciality coffee has been
prepared. If cappuccino or latte macchiato has
been prepared, cappuccino frother rinsing also
takes place.
TPlace a receptacle under the dual spout.
QTPress the On/Off button.
RINSING, CAPPUCCINO
RINSING, the system rinses itself. The
operation stops automatically. Your ENA is
switched off.
EWhen the ENA is switched off with the
On/Off button, the machine does not
consume standby energy.
4 Permanent settings in pro-
gramming mode
Products
You can make the following permanent settings for
espresso and coffee:
UAmount of water: 25ML – 240ML
UCoffee strength: NORMAL, STRONG
UTemperature: NORMAL, HIGH
You can make the following permanent settings for
latte macchiato and cappuccino:
UAmount of milk foam: 3SEC – 120SEC
UInterval: 0SEC – 60SEC
UCoffee strength: NORMAL, STRONG
UAmount of water: 25ML – 240ML
UTemperature: NORMAL, HIGH
You can make the following permanent setting for
hot water:
UAmount of water: 25ML – 450ML
Permanent settings in programming mode always
follow the same model.
Example: Permanently change the coffee strength
(FLAVOUR) for espresso from STRONG to
NORMAL.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until PRODUCT is
displayed.
kTPress the Rotary Switch to enter the
programme item.
SELECT BUTTON
ENext select the button of the product for
which you would like to make settings.
No product is prepared at this point.
<TPress the Espresso button.
ESPRESSO
WATER
gTTurn the Rotary Switch until FLAVOUR is
displayed.
kTPress the Rotary Switch to enter the
programme item.
STRONG
gTTurn the Rotary Switch until NORMAL is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the coffee strength is set.
FLAVOUR
gTTurn the Rotary Switch until EXIT is
displayed.

42
4 Permanent settings in programming mode
kTPress the Rotary Switch to exit the pro-
gramme item.
PRODUCT
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Setting the water hardness
EIf you are using the CLARIS Blue filter
cartridge and have activated it in program-
ming mode, you will not be able to adjust
the water hardness.
The harder the water is, the more frequently the
ENA needs to be descaled. It is therefore important
to adjust the water hardness.
The water hardness can be adjusted on a continu-
ous scale between 1° dH and 30° dH.
Example: Change the water hardness setting from
16°dH to 25°dH.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until HARDNESS
is displayed.
kTPress the Rotary Switch to enter the
programme item.
16°dH
gTTurn the Rotary Switch until 25°dH is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the water hardness is set.
HARDNESS
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Energy-saving mode
The energy-saving mode (Energy Save Mode,
E.S.M.©) helps you to prevent your machine from
consuming power unnecessarily and to actively
save energy:
UENERGYp
USoon after the last preparation, the ENA
stops heating up. After about 5 minutes the
message ENERGY ON is displayed.
UBefore you can prepare a speciality coffee,
speciality coffee with milk, or hot water, the
machine must heat up.
UENERGY-
UThe ENA is constantly ready for use.
UAll speciality coffees as well as hot water can
be prepared without having to wait.
Example: Change the energy-saving mode from
ENERGYp to ENERGY-.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until ENERGYp is
displayed.
kTPress the Rotary Switch to enter the
programme item.
ECONOMYp
gTTurn the Rotary Switch until ECONOMY-
is displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the energy-saving mode is set.
ENERGY-
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY

43
4 Permanent settings in programming mode
pt
es
nl
it
fr
ru
en
de
Automatic switch-off
By instructing your ENA to automatically switch
itself off, you can cut down your energy consump-
tion. If this function is activated, your ENA switches
off automatically after the preset time following
the last action on the machine.
The automatic switch-off can be set to between
15 minutes and 9 hours.
Example: Change the switch-off time from
2HRS to 1HRS.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until OFF AFTER
is displayed.
kTPress the Rotary Switch to enter the
programme item.
2HRS
gTTurn the Rotary Switch until 1HRS is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the switch-off time is set.
OFF AFTER
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Rinses
In the programme item RINSES you can make
the following settings:
UINIT RINSE MANUAL
UThe switch-on rinse must be started
manually.
UINIT RINSE AUTOMATIC
UThe switch-on rinse is started automatically.
UC-RINSE AFTER10'
UYou are prompted to perform a cappuccino
rinse 10 minutes after preparation of a
speciality coffee with milk.
UC-RINSE NOW
UYou are prompted to perform a cappuccino
rinse immediately after preparation of a
speciality coffee with milk.
Example: Change the setting such that cappuccino
frother rinsing is performed immediately after
preparation of a speciality coffee with milk.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until RINSES is
displayed.
kTPress the Rotary Switch to enter the
programme item.
INIT RINSE
gTTurn the Rotary Switch until C-RINSE is
displayed.
kTPress the Rotary Switch to enter the
programme item.
AFTER10'
gTTurn the Rotary Switch until NOW is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK
C-RINSE
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit the pro-
gramme item.
RINSES
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY

44
5 Maintenance
Unit for amount of water
You can change the unit for the amount of water
from ‘ml’ to ‘oz’.
Example: Change the unit for the amount of water
from ML to OZ.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until DISPLAY is
displayed.
kTPress the Rotary Switch to enter the
programme item.
ML
gTTurn the Rotary Switch until OZ is displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the unit for the amount of water is set.
DISPLAY
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Language
In this programme item you can set the language
used by your ENA.
Example: Change the language from ENGLISH
to DEUTSCH.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until LANGUAGE
is displayed.
kTPress the Rotary Switch to enter the
programme item.
ENGLISH
gTTurn the Rotary Switch until DEUTSCH is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the language is set.
SPRACHE
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
BEREIT
5 Maintenance
Your ENA has the following integrated mainte-
nance programmes:
UCappuccino frother cleaning (C-CLEAN)
URinsing the machine (RINSE)
UCappuccino frother rinsing (C-RINSE)
UCleaning the machine (CLEAN)
UChanging the filter (FILTER)
UDescaling the machine (DE-SCALE)
EYou can start the maintenance programmes
at any time in programming mode
(programme item RINSE). If no action is
taken in this programme item, program-
ming mode is exited automatically after
approximately 5 seconds.
Rinsing the machine
You can initiate the rinse operation manually at
any time.
Precondition: READY is displayed.
TPlace a receptacle under the dual spout.
kTPress and hold the Rotary Switch until
RINSE appears.
kTPress the Rotary Switch to enter the
programme item.
C-CLEAN
micro 9

45
5 Maintenance
pt
es
nl
it
fr
ru
en
de
gTTurn the Rotary Switch until RINSE is
displayed.
kTPress the Rotary Switch to initiate the rinse
operation.
RINSING, the system rinses itself.
The operation stops automatically.
READY
Rinsing the milk system
After each milk preparation, the ENA prompts you
to perform a cappuccino rinse.
Precondition: CAPPUCCINO RINSE is
displayed.
TPlace a receptacle under the dual spout.
cTPress the Maintenance button to start
cappuccino frother rinsing.
CAPPUCCINO RINSING, the milk
system is rinsed.
The rinse stops automatically. READY
appears on the display.
Cleaning the milk system
The dual spout must be cleaned daily if milk has
been prepared to make sure it functions perfectly
and also in the interests of hygiene. Your ENA will
not prompt you to clean the dual spout.
CAUTION
If the wrong cleaning agent is used, the machine
could be damaged and/or traces could be left
behind in the milk.
TUse only original JURA maintenance
products.
micro 9
EJURA Cappuccino Cleaner is available from
specialized dealers.
kTPress and hold the Rotary Switch until
RINSE appears.
kTPress the Rotary Switch to enter the
programme item.
C-CLEAN
kTPress the Rotary Switch to start cappuccino
frother cleaning.
CLEANER FOR CAPPU.
TRemove the milk pipe from the receptacle
with milk.
TPour 250 ml of fresh water into a receptacle
and add one capful (max. 15 ml) of Cappuc-
cino Cleaner.
TImmerse the milk pipe in the receptacle.
TPlace another receptacle under the dual
spout.
cTPress the Maintenance button.
CLEANING, the milk system and the pipe
are cleaned.
The operation is interrupted, WATER FOR
CAPPUCCINO.
TRinse the receptacle thoroughly, fill it with
250 ml of fresh water and immerse the milk
pipe in it.
TEmpty the receptacle under the dual spout
and place it back underneath.
cTPress the Maintenance button.
CLEANING, the milk system and the pipe
are rinsed with fresh water.
The operation stops automatically.
READY
micro 9

46
5 Maintenance
Dismantling and rinsing the dual spout
The dual spout must be dismantled and rinsed
daily if milk has been prepared to make sure it
functions perfectly and also in the interests of
hygiene. Your ENA will not prompt you to clean the
dual spout.
TRemove the milk pipe and rinse thoroughly
under running water.
TPress the releasing devices and pull the dual
spout down and off.
TPush the milk system down and remove it.
TDismantle the milk system into its individual
parts.
TRinse all parts under running water. If there
are severely dried on milk residues, firstly
immerse the individual parts in JURA
Cappuccino Cleaner and then clean them
thoroughly.
TFit the air intake pipe.
TReassemble the milk system, noting the
numbering on the parts.
TInsert the assembled individual parts into
the dual spout and press them together.
TFit the dual spout on the machine. It will
click into place audibly.
Inserting and activating the filter
Your ENA no longer has to be descaled if you are
using the CLARIS Blue filter cartridge. If you did not
activate the filter cartridge the first time you used
the machine, you can do this now as follows.
EPerform the ‘inserting the filter’ operation
without any interruptions. This will ensure
that your ENA always produces its best.




47
5 Maintenance
pt
es
nl
it
fr
ru
en
de
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until FILTER- is
displayed.
kTPress the Rotary Switch to enter the
programme item.
NO-
gTTurn the Rotary Switch until YESp is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK
INSERT FILTER
TRemove and empty the water tank.
TOpen the filter holder.
TInsert the filter cartridge into the water tank,
exerting slight pressure.
TClose the filter holder. It will click into place
audibly.
EAfter two months, the filter will cease to
work. Set the date on the date plate on the
filter holder in the water tank.
TFill the water tank with fresh, cold water and
reinsert it.
TPlace a receptacle (at least 500 ml) under the
hot-water spout.
cTPress the Maintenance button.
FILTER RINSING, water flows out of
the hot-water spout.
EYou can interrupt rinsing of the filter at any
time by pressing any button. Press the
Maintenance button c, to continue with
rinsing of the filter.
EThe water may be slightly discoloured. This
is not harmful to health and does not affect
the taste.
Rinsing of the filter stops automatically.
HEATING
READY
The filter is now activated.
Changing the filter
EAfter 50 litres of water have flowed through,
the filter will cease to work. Your ENA will
automatically prompt you to change the
filter.
EAfter two months, the filter will cease to
work. Set the date on the date plate on the
filter holder in the water tank.
EIf the CLARIS Blue filter cartridge is not
activated in programming mode, you will
not be prompted to change the filter.
Precondition: FILTER / READY is displayed.
cTPress the Maintenance button.
INSERT FILTER
TRemove and empty the water tank.
TOpen the filter holder and remove the old fil-
ter cartridge.
TInsert a new filter cartridge into the water
tank, exerting slight pressure.
TClose the filter holder. It will click into place
audibly.
TFill the water tank with fresh, cold water and
reinsert it.
TPlace a receptacle (at least 500 ml) under the
hot-water spout.

48
5 Maintenance
kTPress the Rotary Switch.
FILTER RINSING, water flows out of
the hot-water spout.
EYou can interrupt rinsing of the filter at any
time by pressing any button. Press the
Maintenance button c, to continue with
rinsing of the filter.
EThe water may be slightly discoloured. This
is not harmful to health and does not affect
the taste.
Rinsing of the filter stops automatically.
HEATING
READY
Cleaning the machine
After 180 preparations or 80 switch-on rinses, the
ENA will prompt you to clean it.
CAUTION
If the wrong cleaning agent is used, the machine
could be damaged and/or traces could be left
behind in the water.
TUse only original JURA maintenance
products.
EThe cleaning programme lasts approxi-
mately 15 minutes.
EDo not interrupt the cleaning programme.
The quality of cleaning will be impaired if
you do so.
EJURA cleaning tablets are available from
specialized dealers.
Precondition: CLEAN / READY is displayed.
cTPress the Maintenance button.
EMPTY TRAY
TEmpty the drip tray and coffee grounds
container and reinsert them.
PRESS RINSE
TPlace a receptacle under the dual spout.
cTPress the Maintenance button.
CLEANING, water flows out of the dual
spout.
The operation is interrupted, ADD
TABLET.
TOpen the powder chute for ground coffee
and drop in a JURA cleaning tablet.
TClose the powder chute for ground coffee.
PRESS RINSE
cTPress the Maintenance button.
CLEANING, water flows out of the dual
spout repeatedly.
EMPTY TRAY
TEmpty the drip tray and coffee grounds
container and reinsert them.
HEATING
READY
Descaling the machine
The ENA builds up deposits of limescale over time
and automatically prompts you to descale it when
necessary. The degree of calcification depends on
the hardness of your water.
JCAUTION
If the descaling agent comes into contact with the
skin or eyes, this can cause irritation.
TAvoid contact with the skin or eyes.
TRinse off descaling agent with clean water.
Should you get any descaling agent in your
eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine
could be damaged and/or traces could be left
behind in the water.
TUse only original JURA maintenance
products.