England's Stove Works 55-SHP22 User manual

P.O. Box 206 Monroe, VA 24574 www.englanderstoves.com Phone: [phone] Fax: [phone]
Pellet Stoves
Wood Stoves
Gas Stoves
Mult
i
-
F
uel
S
toves
Installing the PU-DTSTAT
BEFORE BEGINNING THERMOSTAT INSTALLATION BE CERTAIN
THE STOVE IS UNPLUGGED AND COMPLETELY COOL. DEPENDING
ON WHICH STOVE THE THERMOSTAT IS BEING INSTALLED ON,
THE CONTROL BOARD MAY NEED TO BE REMOVED FOR
INSTALLATION.
1. Using a small, slotted screwdriver (often referred to as a jeweler’s screwdriver),
loosen the two screws on the front of the J18 thermostat terminal, shown below
and remove the jumper which is installed in the terminal from the factory. This
jumper should be set aside and saved.
2. Insert one of the thermostat wires into each of the terminals on the bottom of the
J18 thermostat connection block and tighten the screws on the front of the
thermostat terminal. The thermostat wires should be securely held in place by
these screws (remember that the thermostat is not polarity specific, so it will not
matter which wire goes into either terminal).
Connect
thermostat
wires here
(
J18
)

2
3. Pull the two halves of the thermostat apart so that the interior of the thermostat
is visible. Install one thermostat wire into the “G” terminal of the thermostat and
the other wire into the “W” terminal (it does not matter which wire color is
installed at each terminal). Use the previously mentioned jeweler’s screwdriver to
tighten the retaining screws and tightly secure the wires into the thermostat.
4. With the two halves of the thermostat still apart, be certain to set the selector
switch to “Electric or Heat Pump”.
5. After mounting the thermostat on the wall and reinstalling all panels removed
from the stove, the batteries can be inserted into the thermostat. Once powered on,
the fan control switch (lower left switch) of the thermostat must be slid to the word
“On” and the system control switch (lower right switch) must be slid to the “Heat”
position, as shown below.
Set fan
control
switch to
“On”
Set system
control
switch to
“Hea
t
”
Set switch to
“Electric or
Heat Pump”
Connect one
thermostat wire
“W” terminal.”
Connect one
thermostat wire
“G” terminal.”

3
6. Consult the Owner’s Manual of your stove (and see the chart below) for more
details on how the thermostat works with your control board to manage heat output
and fuel usage.
StoveThermostatFunctionStoveThermostatFunction
25‐PDV
55‐SHP22
55‐TRP22
Thermostatputsstoveintoidle
modewhenthecallforheatis
gone(controlboarddoesnot
indicatechange).
10‐CDV
49‐SHC22
49‐TRC22
Thermostatputsstoveintoidle
modewhenthecallforheatis
gone(controlboarddoesnot
indicatechange).
25‐PDVC
55‐SHP10
55‐TRP10
Thermostatputsstoveintoidle
modewhenthecallforheatis
gone(controlboarddoesnot
indicatechange).
10‐CPM
49‐SHCPM
49‐TRCPM
Thermostatturnsstove
completelyonandoff.
25‐PUF
55‐SHP240
55‐TRP240
Thermostatputsstoveintoidle
modewhenthecallforheatis
gone(controlboarddoesnot
indicatechange).
25‐EP
55‐SHPEP
55‐TRPEP
Thermostatturnsstove
completelyonandoff.