ENNOPRO GlassOuse GS09 User manual

GS09 - PROXIMITY SWITCH USER MANUAL
WARNINGS
• While removing your Proximity Switch from your
GlassOuse or other devices, pay attention not to
damage the wire joining points both on the 3.5mm
jack connector and the Proximitry Switch module
parts.
•To change the battery, remove the tiny screws at
the bottom. Pay attention to the + and – pole
remarks of the battery box during installation.
•Keep Proximity Switch away from magnets.
7th Floor, Huarong Building, Qiaolian East, Bulong Road,
Longgang District, 518129, Shenzhen, Guangdong, China
P. 0086-755-8920-5835 F. 0086-755-8980-5835-812
[email protected] | www.glassouse.com | www.ennopro.com
PROXIMITY SWITCH
With an 8.63cm activation surface, Proximity Switch is highly
sensitive to detect different levels of distances from the
activation surface to perform your clicks. You can use any
part of your body to activate the switch via hovering over the
surface. GS09 Proximity Switch comes with a mono 3.5mm
jack connector plug and it is compatible with any kind of
adapted devices besides GlassOuse V1.2 and higher.
Proximity Switch works with 3x AAA dry or Ni-MH batteries
and its smart battery system turns the device off in one hour
if it is not used. Auditory and visual feedback can be
selected according to the user’s needs easily or can be
turned off if desired.

ACTIVATION SURFACE
SENSITIVITY BUTTON
FEEDBACK/POWER
BUTTON
3.5MM JACK CABLE
USER MANUAL
7th Floor, Huarong Building, Qiaolian East, Bulong Road,
Longgang District, 518129, Shenzhen, Guangdong, China
P. 0086-755-8920-5835 F. 0086-755-8980-5835-812
[email protected] | www.glassouse.com | www.ennopro.com
FEEDBACK SIGNALS
You can set the click feedback according to your needs. Use the tiny power button on the switch module for the
desired feedback type as following. A second of press is enough to change the feedback mode.
1. Press the power button once – only visual LED feedback on without any auditory sound.
2. Press the power button once again – only auditory sound feedback on without no LED.
3. Press the power button once again – both visual LED and auditory sound feedback together.
4. Press the power button once again – no visual LED or auditory sound feedback.
SENSITIVITY SETTINGS
You can set the sensitivity of your Proximity Switch to select a further or closer hover distance from the switch
surface as following. A second of press is enough to change the sensitivity.
1.
Press the setting button once – low sensitivity. Hovering must be very close to the switch surface to activate
the switch. LED signal blinks once.
2.
Press the setting button once again – medium sensitivity. Hovering can be a bit further to the switch surface
to activate the switch. LED signal blinks twice.
3.
Press the setting button once again – high sensitivity. Hovering can be very high from the switch surface to
activate the switch. LED signal blinks three times.
SWITCH CONNECTION
1. Plug Proximity Switch to Glassouse V1.2 or any 3.5mm jack adapted device via 3.5mm connector.
2.
Adjust the position of Procximity Switch until you feel comfortable enough to hover any part of your body over
the switch surface.
3. Press the power button on your switch for 3 seconds to activate Proximity Switch. The LED light will flash with
beep sound. Press the power button again for 3 seconds to turn off your Proximity Switch. The LED light will flash
with beep to indicate that the switch is turned off.
GS09 - PROXIMITY SWITCH
Dimensions: Diameter: 96.9mm x Thickness: 28.55mm
Weight: 124±2g
Cable Length: 185±5cm
Activation Surface: 86.30mm
Battery Type: 3x AAA Dry or Ni-MH Batteries
DEVICE