HP 6125G Installation manual
HP 6125 Blade Switch Series
Fundamentals
Command Reference
Part number: 5998-3164
Software version: Release 2103
Document version: 6W100-20120907
Legal and notice information
© Copyright 2012 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in any form or by any means without
prior written consent of Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or
use of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained
herein.
i
Contents
CLI configuration commands······································································································································· 1
command-alias enable·············································································································································1
command-alias mapping ·········································································································································1
command-privilege···················································································································································2
display clipboard ·····················································································································································3
display command-alias ············································································································································4
display history-command ·········································································································································4
display hotkey···························································································································································5
hotkey ········································································································································································6
quit ·············································································································································································7
return··········································································································································································8
screen-length disable················································································································································8
super ··········································································································································································9
super authentication-mode·······································································································································9
super password ····················································································································································· 10
system-view ···························································································································································· 11
Login management commands ·································································································································12
acl (user interface view)········································································································································ 12
activation-key ························································································································································· 13
auto-execute command ········································································································································· 14
authentication-mode ·············································································································································· 16
command accounting············································································································································ 17
command authorization········································································································································ 18
databits··································································································································································· 18
display ip http ························································································································································ 19
display ip https ······················································································································································ 20
display telnet client configuration························································································································ 21
display user-interface ············································································································································ 21
display users ·························································································································································· 23
display web users·················································································································································· 24
escape-key······························································································································································ 25
flow-control····························································································································································· 27
free user-interface ·················································································································································· 27
free web-users························································································································································ 28
history-command max-size ··································································································································· 29
idle-timeout ····························································································································································· 29
ip http acl ······························································································································································· 30
ip http dscp ···························································································································································· 31
ip http enable························································································································································· 31
ip http port······························································································································································ 32
ip https acl······························································································································································ 33
ip https certificate access-control-policy ·············································································································· 33
ip https enable ······················································································································································· 34
ip https port ···························································································································································· 35
ip https ssl-server-policy········································································································································· 35
ipv6 http dscp ························································································································································ 36
lock·········································································································································································· 36
parity······································································································································································· 37
ii
protocol inbound ··················································································································································· 38
screen-length ·························································································································································· 38
send ········································································································································································ 39
set authentication password································································································································· 41
shell········································································································································································· 41
speed (user interface view)··································································································································· 42
stopbits···································································································································································· 43
telnet ······································································································································································· 43
telnet client dscp ···················································································································································· 44
telnet client ipv6 dscp ··········································································································································· 45
telnet client source ················································································································································· 45
telnet ipv6······························································································································································· 46
telnet server dscp··················································································································································· 47
telnet server enable ··············································································································································· 47
telnet server ipv6 dscp ·········································································································································· 48
terminal type ·························································································································································· 48
user privilege level ················································································································································ 49
user-interface·························································································································································· 50
FTP configuration commands ····································································································································52
FTP server configuration commands····························································································································· 52
display ftp-server···················································································································································· 52
display ftp-user······················································································································································· 53
free ftp user ···························································································································································· 54
ftp server acl ·························································································································································· 54
ftp server dscp ······················································································································································· 55
ftp server enable···················································································································································· 55
ftp timeout······························································································································································· 56
ftp update······························································································································································· 56
FTP client configuration commands······························································································································ 57
ascii········································································································································································· 57
binary ····································································································································································· 58
bye ·········································································································································································· 58
cd ············································································································································································ 59
cdup········································································································································································ 60
close········································································································································································ 60
debugging······························································································································································ 61
delete ······································································································································································ 62
dir············································································································································································ 62
disconnect ······························································································································································ 64
display ftp client configuration····························································································································· 64
ftp ············································································································································································ 65
ftp client dscp························································································································································· 66
ftp client ipv6 dscp················································································································································ 66
ftp client source······················································································································································ 67
ftp ipv6 ··································································································································································· 68
get ··········································································································································································· 68
lcd ··········································································································································································· 69
ls·············································································································································································· 70
mkdir······································································································································································· 71
open········································································································································································ 71
open ipv6······························································································································································· 72
passive···································································································································································· 73
put ··········································································································································································· 74
pwd········································································································································································· 74
iii
quit ·········································································································································································· 75
remotehelp ····························································································································································· 75
rmdir ······································································································································································· 77
user ········································································································································································· 78
verbose ··································································································································································· 79
TFTP client configuration commands·························································································································80
display tftp client configuration···························································································································· 80
tftp-server acl·························································································································································· 80
tftp ··········································································································································································· 81
tftp client dscp························································································································································ 82
tftp client ipv6 dscp··············································································································································· 83
tftp client source····················································································································································· 83
tftp ipv6 ·································································································································································· 84
File system management commands ························································································································86
cd ············································································································································································ 86
copy ········································································································································································ 86
delete ······································································································································································ 87
dir············································································································································································ 88
display nandflash file-location ····························································································································· 90
display nandflash badblock-location··················································································································· 91
display nandflash page-data ······························································································································· 92
execute ··································································································································································· 93
file prompt ······························································································································································ 93
fixdisk······································································································································································ 94
format······································································································································································ 94
mkdir······································································································································································· 95
more········································································································································································ 95
move ······································································································································································· 96
pwd········································································································································································· 97
rename···································································································································································· 97
reset recycle-bin····················································································································································· 98
rmdir ······································································································································································· 99
undelete································································································································································100
Configuration file management commands ·········································································································· 102
archive configuration ··········································································································································102
archive configuration interval ····························································································································102
archive configuration location ···························································································································103
archive configuration max··································································································································105
backup startup-configuration······························································································································105
configuration replace file····································································································································106
display archive configuration·····························································································································107
display current-configuration······························································································································108
display default-configuration······························································································································109
display saved-configuration ·······························································································································110
display startup ·····················································································································································112
display this ···························································································································································113
reset saved-configuration····································································································································115
restore startup-configuration·······························································································································115
save·······································································································································································116
slave auto-update config·····································································································································118
startup saved-configuration ································································································································119
iv
Software upgrade commands································································································································ 121
boot-loader···························································································································································121
bootrom ································································································································································122
bootrom-update security-check enable··············································································································123
display boot-loader ·············································································································································123
display patch ·······················································································································································124
display patch information···································································································································125
patch install··························································································································································126
Device management commands ···························································································································· 128
clock datetime······················································································································································128
clock summer-time one-off···································································································································128
clock summer-time repeating······························································································································129
clock timezone·····················································································································································130
copyright-info enable ··········································································································································131
display alarm ·······················································································································································132
display clock ························································································································································133
display cpu-usage················································································································································134
display cpu-usage history ···································································································································136
display device······················································································································································138
display device manuinfo·····································································································································139
display diagnostic-information ···························································································································140
display job ···························································································································································141
display memory ···················································································································································142
display reboot-type··············································································································································143
display schedule job ···········································································································································144
display schedule reboot······································································································································145
display system-failure ··········································································································································145
display transceiver ··············································································································································146
display transceiver alarm ···································································································································147
display transceiver diagnosis·····························································································································149
display transceiver manuinfo ·····························································································································150
display version·····················································································································································151
display version-update-record ····························································································································152
header ··································································································································································153
job·········································································································································································155
reboot ···································································································································································155
reset unused porttag············································································································································156
reset version-update-record ································································································································157
schedule job·························································································································································157
schedule reboot at···············································································································································159
schedule reboot delay·········································································································································160
shutdown-interval·················································································································································161
sysname································································································································································161
system-failure························································································································································162
time at···································································································································································163
time delay·····························································································································································165
view ······································································································································································166
Support and other resources ·································································································································· 168
Contacting HP ······························································································································································168
Subscription service ············································································································································168
Related information······················································································································································168
Documents····························································································································································168
Websites·······························································································································································168
v
Conventions ··································································································································································169
Index ········································································································································································ 171
1
CLI configuration commands
command-alias enable
Syntax
command-alias enable
undo command-alias enable
View
System view
Default level
2: System level
Description
Use command-alias enable to enable the command keyword alias function.
Use undo command-alias enable to disable the command keyword alias function.
By default, the command keyword alias function is disabled.
Disabling the command keyword alias function does not delete the configured aliases, but the aliases do
not take effect anymore.
Related commands: command-alias mapping.
Examples
# Enable the command keyword alias function.
<Sysname> system-view
[Sysname] command-alias enable
# Disable the command keyword alias function.
<Sysname> system-view
[Sysname] undo command-alias enable
command-alias mapping
Syntax
command-alias mapping cmdkey alias
undo command-alias mapping cmdkey
View
System view
Default level
2: System level
Parameters
cmdkey: Complete form of the first keyword of a non-undo command, or the second keyword of an undo
command.
2
alias: Alias for the keyword, which must be different from the first keyword of any non-undo command.
Description
Use command-alias mapping to configure a command keyword alias.
Use undo command-alias mapping to delete a command keyword alias.
By default, a command keyword has no alias.
Command keyword aliases take effect only after you enable the command keyword alias function.
Examples
# Define show as the alias of the display keyword.
<Sysname> system-view
[Sysname] command-alias mapping display show
After you configure the alias, you can enter show to execute a display command. For example, you can
enter show clock to execute the display clock command.
# Delete the alias of the display keyword.
<Sysname> system-view
[Sysname] undo command-alias mapping display
command-privilege
Syntax
command-privilege level level view view command
undo command-privilege view view command
View
System view
Default level
3: Manage level
Parameters
level level: Command level, which ranges from 0 to 3.
view view: Specifies a view.
command: Command to be set in the specified view.
Description
Use command-privilege to assign a level for a specific command in a view.
Use undo command-privilege to restore the default.
By default, each command in a view has a specified level.
Command levels include four privileges: visit (0), monitor (1), system (2), and manage (3). You can
assign a privilege level according to the user's need. When logging in to the device, the user can access
the assigned level and all levels below it.
Level changes can cause maintenance, operation, and security problems. HP recommends using the
default command level or modifying the command level under the guidance of professional staff.
The command specified for the command-privilege command must be complete, and have valid
parameters. For example, the default level of the tftp server-address { get | put | sget }source-filename
3
[ destination-filename ][ source { interface interface-type interface-number | ip source-ip-address } ]
command is 3. To enable users with the privilege level 0 to execute the tftp server-address put
source-filename command (such as tftp 192.168.1.26 put syslog.txt) and disable them from specifying the
get, sget, source, or destination-filename option, configure the command-privilege level 0 view shell tftp
1.1.1.1 put a.cfg command.
The command specified for the undo command-privilege view command can be incomplete. For
example, configuring the undo command-privilege view system ftp command restores all commands
starting with ftp (such as ftp server acl, ftp server enable, and ftp timeout) to their default level. If you
have modified the level of commands ftp server enable and ftp timeout, and you want to restore only the
ftp server enable command to its default level, use the undo command-privilege view system ftp server
command.
If you change the command level of a command in a specified view from the default command level to
a lower level, you must change the command levels of the quit command and the command used to enter
this view. For example, the default command level of commands interface and system-view is 2 (system
level). To make the interface command available to the level 1 users, execute the following commands:
command-privilege level 1view shell system-view, command-privilege level 1 view system interface
gigabitethernet1/0/1, and command-privilege level 1 view system quit. Then, the level 1 users can
enter system view, execute the interface gigabitethernet command, and return to user view.
Examples
# Set the command level of the interface command to 0 in system view.
<Sysname> system-view
[Sysname] command-privilege level 0 view system interface
display clipboard
Syntax
display clipboard [ |{ begin | exclude | include } regular-expression ]
View
Any view
Default level
1: Monitor level
Parameters
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Description
Use display clipboard to display data in the clipboard.
To copy some content to the clipboard:
1. Move the cursor to the starting position of the content, and then press the Esc+Shift+, combination.
2. Move the cursor to the ending position of the content, and then press the Esc+Shift+. combination.
4
Examples
# Display data in the clipboard.
<Sysname> display clipboard
---------------- CLIPBOARD-----------------
display current-configuration
display command-alias
Syntax
display command-alias [ |{ begin | exclude | include } regular-expression ]
View
Any view
Default level
1: Monitor level
Parameters
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Description
Use display command-alias to display the command keyword alias configuration.
Examples
# Display the command keyword alias configuration.
<Sysname> display command-alias
Command alias is enabled
index alias command key
1 show display
display history-command
Syntax
display history-command [ |{ begin | exclude | include } regular-expression ]
View
Any view
Default level
1: Monitor level
Parameters
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
5
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Description
Use display history-command to display commands saved in the command history buffer.
By default, the system can save up to 10 commands in the buffer. You can use the history-command
max-size command to change the buffer size.
Examples
# Display all commands saved in the command history buffer.
<Sysname> display history-command
display history-command
system-view
vlan 2
quit
display hotkey
Syntax
display hotkey [ |{ begin | exclude | include } regular-expression ]
View
Any view
Default level
1: Monitor level
Parameters
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Description
Use display hotkey to display hotkey information.
Examples
# Display hotkey information.
<Sysname> display hotkey
----------------- HOTKEY -----------------
=Defined hotkeys=
Hotkeys Command
CTRL_G display current-configuration
6
CTRL_L display ip routing-table
CTRL_O undo debug all
=Undefined hotkeys=
Hotkeys Command
CTRL_T NULL
CTRL_U NULL
=System hotkeys=
Hotkeys Function
CTRL_A Move the cursor to the beginning of the current line.
CTRL_B Move the cursor one character left.
CTRL_C Stop current command function.
CTRL_D Erase current character.
CTRL_E Move the cursor to the end of the current line.
CTRL_F Move the cursor one character right.
CTRL_H Erase the character left of the cursor.
CTRL_K Kill outgoing connection.
CTRL_N Display the next command from the history buffer.
CTRL_P Display the previous command from the history buffer.
CTRL_R Redisplay the current line.
CTRL_V Paste text from the clipboard.
CTRL_W Delete the word left of the cursor.
CTRL_X Delete all characters up to the cursor.
CTRL_Y Delete all characters after the cursor.
CTRL_Z Return to the User View.
CTRL_] Kill incoming connection or redirect connection.
ESC_B Move the cursor one word back.
ESC_D Delete remainder of word.
ESC_F Move the cursor forward one word.
ESC_N Move the cursor down a line.
ESC_P Move the cursor up a line.
ESC_< Specify the beginning of clipboard.
ESC_> Specify the end of clipboard.
hotkey
Syntax
hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U } command
undo hotkey { CTRL_G | CTRL_L | CTRL_O | CTRL_T | CTRL_U }
View
System view
Default level
2: System level
Parameters
CTRL_G: Assigns a command to Ctrl+G.
7
CTRL_L: Assigns a command to Ctrl+L.
CTRL_O: Assigns a command to Ctrl+O.
CTRL_T: Assigns a command to Ctrl+T.
CTRL_U: Assigns a command to Ctrl+U.
command: Command to be assigned to the hotkey.
Description
Use hotkey to assign a command to a configurable hotkey.
Use undo hotkey to restore the default.
By default:
•Ctrl_G: display current-configuration (display the running configuration).
•Ctrl_L: display ip routing-table (display the IPv4 routing table information).
•Ctrl_O: undo debugging all (disable all debugging functions).
•Ctrl_T: No command is assigned to this hotkey.
•Ctrl_U: No command is assigned to this hotkey.
Examples
# Assign the display tcp status command to the hotkey Ctrl+T.
<Sysname> system-view
[Sysname] hotkey ctrl_t display tcp status
quit
Syntax
quit
View
Any view
Default level
0: Visit level (executed in user view)
2: System level (executed in other views)
Description
Use quit to return to the upper-level view.
In user view, this command disconnects you from the device.
Examples
# Return from GigabitEthernet 1/0/1 interface view to system view and then to user view.
[Sysname-GigabitEthernet1/0/1] quit
[Sysname] quit
<Sysname>
8
return
Syntax
return
View
Any view except user view
Default level
2: System level
Description
Use return to return to user view from any other view. Pressing Ctrl+Z has the same effect.
Related commands: quit.
Examples
# Return to user view from GigabitEthernet 1/0/1 interface view.
[Sysname-GigabitEthernet1/0/1] return
<Sysname>
screen-length disable
Syntax
screen-length disable
undo screen-length disable
View
User view
Default level
1: Monitor level
Description
Use screen-length disable to disable pausing between screens of output for the current session.
Use undo screen-length disable to enable pausing between screens of output for the current session.
By default, a login user uses the settings of the screen-length command. The default settings of the
screen-length command are: pausing between screens of output and displaying up to 24 lines on a
screen.
When the screen pause function is disabled, all output is displayed at one time and the screen is
refreshes continuously.
This command only takes effect for the current session. When you log out, the setting by this command
is restored to the default.
Related commands: screen-length.
Examples
# Disable pausing between screens of output for the current session.
<Sysname> screen-length disable
9
super
Syntax
super [ level ]
View
User view
Default level
0: Visit level
Parameters
level: User level, which ranges from 0 to 3 and defaults to 3.
Description
Use super to switch from the current user privilege level to a specified user privilege level.
If a level is not specified, the command switches the user privilege level to 3.
There are four user privilege levels: visit (0), monitor (1), system (2), and manage (3). You can assign
different privilege levels to different users. After login, a user can access the commands at or under the
assigned level.
A user can switch to a lower privilege level unconditionally. To switch to a higher privilege level, an AUX
user interface user (logged in through the console port) does not need to provide any password, but a
VTY user must enter the switching password set with the super password command. If the entered
password is incorrect or no password is configured for switching to the level, the switching operation
fails.
Related commands: super password and super authentication-mode.
Examples
# Switch to user privilege level 2 from user privilege level 3.
<Sysname> super 2
User privilege level is 2, and only those commands can be used
whose level is equal or less than this.
Privilege note: 0-VISIT, 1-MONITOR, 2-SYSTEM, 3-MANAGE
# Switch back to user privilege level 3. (Suppose the switching password is 123 . If no password is set,
users cannot switch to user privilege level 3.)
<Sysname> super 3
Password:
User privilege level is 3, and only those commands can be used
whose level is equal or less than this.
Privilege note: 0-VISIT, 1-MONITOR, 2-SYSTEM, 3-MANAGE
super authentication-mode
Syntax
super authentication-mode {local |scheme } *
undo super authentication-mode
10
View
System view
Default level
2: System level
Parameters
local: Uses the local password set with the super password command for user privilege level switching
authentication. If no password is set with the command, the system allows a console port user to switch
the privilege level without authentication, but denies the switching requests of VTY users.
scheme: Uses AAA for user privilege level switching authentication. For more information about AAA,
see Security Configuration Guide.
local scheme: Uses the local password, if configured, for user privilege level switching authentication. If
the password is not configured, the system allows a console port user to switch the privilege level but uses
AAA to authenticate VTY users.
scheme local: Uses AAA for user privilege level switching authentication. If the AAA configuration is
incomplete or invalid or the server does not respond, the system uses the local password for the
authentication.
Description
Use super authentication-mode to set the authentication mode for user privilege level switching.
Use undo super authentication-mode to restore the default.
By default, the authentication mode for the user privilege level switching is local.
Related commands: super password.
Examples
# Set the authentication mode for the user privilege level switching to local.
<Sysname> system-view
[Sysname] super authentication-mode local
# Set the authentication mode for the user privilege level switching to scheme local.
<Sysname> system-view
[Sysname] super authentication-mode scheme local
super password
Syntax
super password [level user-level ] { cipher | simple }password
undo super password [ level user-level ]
View
System view
Default level
2: System level
Parameters
level user-level: User privilege level, which ranges from 1 to 3 and defaults to 3.
11
cipher: Sets a ciphertext password.
simple: Sets a plaintext password.
password: Specifies the password string. This argument is case sensitive. If simple is specified, it must be
a string of 1 to 16 characters. If cipher is specified, it must be a ciphertext string of 1 to 53 characters.
Description
Use super password to set the password used to switch from the current user privilege level to a higher
one.
Use undo super password to restore the default.
By default, no password is set for switching to a higher privilege level.
Whether you specify the cipher or simple keyword, the password is saved in cipher text in the
configuration file.
Examples
# Use the password abc in plain text to authenticate a user switching to privilege level 3.
<Sysname> system-view
[Sysname] super password level 3 simple abc
system-view
Syntax
system-view
View
User view
Default level
2: System level
Description
Use system-view to enter system view from user view.
Related commands: quit and return.
Examples
# Enter system view from user view.
<Sysname> system-view
System View: return to User View with Ctrl+Z.
[Sysname]
12
Login management commands
acl (user interface view)
Syntax
To use a basic or advanced ACL:
acl [ ipv6 ] acl-number { inbound | outbound }
undo acl [ ipv6 ] acl-number { inbound | outbound }
To use an Ethernet frame header ACL:
acl acl-number inbound
undo acl acl-number inbound
View
VTY user interface view
Default level
2: System level
Parameters
ipv6: When this keyword is present, the command supports IPv6; otherwise, it supports IPv4.
acl-number: Number of the ACL:
•Basic ACL—2000 to 2999
•Advanced ACL—3000 to 3999
•Ethernet frame header ACL—4000 to 4999
inbound: Restricts Telnet or SSH connections established in the inbound direction through the VTY user
interface. If the received packets for establishing a Telnet or SSH connection are permitted by an ACL rule,
the connection is allowed to be established. When the device functions as a Telnet server or SSH server,
this keyword is used to control access of Telnet clients or SSH clients.
outbound: Restricts Telnet connections established in the outbound direction through the VTY user
interface. If the packets sent for establishing a Telnet connection are permitted by an ACL rule, the
connection is allowed to be established. When the device functions as a Telnet client, this keyword is
used to define Telnet servers accessible to the client.
Description
Use acl to reference ACLs to control access to the VTY user interface.
Use undo acl to cancel the ACL application. For more information about ACL, see ACL and QoS
Configuration Guide.
By default, access to the VTY user interface is not restricted.
If no ACL is referenced in VTY user interface view, the VTY user interface has no access control over
establishing a Telnet or SSH connection.
If an ACL is referenced in VTY user interface view, the connection is permitted to be established only
when packets for establishing a Telnet or SSH connection match a permit statement in the ACL.
13
If you configure two or more ACLs of the same type for a VTY user interface, only the last one takes effect.
A basic ACL with the inbound keyword and a basic ACL with the outbound keyword are considered
different types of ACLs. The same is true for advanced ACLs.
If you apply more than one type of ACL to a VTY user interface, the match order is basic ACL, advanced
ACL, and Ethernet frame header ACL.
Examples
# Allow only the user with the IP address of 192.168.1.26 to access the device through Telnet or SSH.
<Sysname> system-view
[Sysname] acl number 2001
[Sysname-acl-basic-2001] rule permit source 192.168.1.26 0
[Sysname-acl-basic-2001] quit
[Sysname] user-interface vty 0
[Sysname-ui-vty0] acl 2001 inbound
After your configuration, user A (with the IP address 192.168.1.26) can Telnet to the device while user B
(with the IP address 192.168.1.60) cannot Telnet to the device. Upon a connection failure, a message
appears, saying "%connection closed by remote host!"
# Allow the device to only Telnet to the Telnet server with IP address 192.168.1.41.
<Sysname> system-view
[Sysname] acl number 3001
[Sysname-acl-adv-3001] rule permit tcp destination 192.168.1.41 0
[Sysname-acl-adv-3001] quit
[Sysname] user-interface vty 0 7
[Sysname-ui-vty0-7] acl 3001 outbound
[Sysname-ui-vty0-7] return
<Sysname>
After your configuration, if you Telnet to 192.168.1.46, your operation fails.
<Sysname> telnet 192.168.1.46
%Can't access the host from this terminal!
But you can Telnet to 192.168.1.41.
<Sysname> telnet 192.168.1.41
Trying 192.168.1.41 ...
Press CTRL+K to abort
Connected to 192.168.1.41 ...
activation-key
Syntax
activation-key character
undo activation-key
View
AUX user interface view
Default level
3: Manage level
Other manuals for 6125G
24
This manual suits for next models
1
Table of contents
Other HP Switch manuals
HP
HP Aruba Instant On 1930 Assembly instructions
HP
HP A5120 EI Series User manual
HP
HP Brocade 4Gb SAN Switch User manual
HP
HP ProCurve 1600M Operator's manual
HP
HP ProCurve 1600M User manual
HP
HP NJ5000-5G-PoE+ User manual
HP
HP Voltaire InfiniBand Grid Director 4200 QDR Operator's manual
HP
HP 1x1x16 - IP Console Switch KVM Quick start guide
HP
HP ProCurve 5304xl User manual
HP
HP aruba 9300-32D Series User manual
HP
HP ProCurve Switch 2650 Manual
HP
HP HPE FlexFabric 5944 Series User manual
HP
HP ProCurve 6120G/XG User manual
HP
HP 6125G/XG User instructions
HP
HP A3100-8 v2 SI Installation manual
HP
HP HP 830 Series User manual
HP
HP 445860-B21 - 10Gb Ethernet BL-c Switch User manual
HP
HP 438031-B21 - 1:10Gb Ethernet BL-c Switch User guide
HP
HP E4510-48G Operating manual
HP
HP PROCURVE 2910AL User manual
