enware FHS011 Assembly instructions

Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: [phone] Fax: [phone]
I00063_Nov 17
FOOD SERVICE PRE-RINSE ASSEMBLIES
Installation, Operating & Maintenance Instructions

1 Call 1300 369 273 www.enware.com.au
page
PRODUCT CODES 3
TECHNICAL DATA 4
INSTALLATION COMPLIANCE 4
ASSEMBLY & INSTALLATION
Installing the base 5
Hob mounted single inlet FS011
FS010
6
Hob mounted twinner body FS015 7
Hob mounted exposed
breech
FS012 8
Hob mounted concealed
adjustable breech
FS013 9
Wall mounted exposed
breech
FS022 11
Wall mounted single inlet FS021
FS020
12
Wall mounted recessed
(concealed in wall)
FS023 13
Installing the riser, pot ller & spray arm 15
WATER CONNECTIONS 17
OPERATING INSTRUCTIONS 18
CLEANING 18
SERVICE AND MAINTENANCE 20
SPARE PARTS 20
TROUBLESHOOTING 21
PRODUCT WARRANTY FOR AUSTRALIA 22
contents

www.enware.com.au Call 1300 369 273 2
TROUBLESHOOTING
Thank you for choosing Enware’s Food Service Tapware . Designed and manufactured in Australia, the
Food Service Range is built using premium quality hose, brass and stainless steel to provide maximum
strength and durability. It can quickly and efficiently remove waste material from plates, pans and utensils
prior to them being washed.
Designed and manufactured in Australia
Built tough for the demands of busy commercial
kitchens where performance and reliability are
crucial
Proven durability in some of Australia’s leading
restaurants and fast food stores
Easy to use, ergonomically designed spray-trigger
and tap handles
Self-closing trigger spray turns off water when
not in use
Trigger spray achieves 6-Star WELS Rating with
efficient high velocity spray
Quarter turn jumper valve used in conjunction
with lever handles allow for easy control of water
flow
High water efficiency, reducing water costs
and energy costs for heating water
Integral dual check valve aid in backflow
prevention and protect the water supply from
contamination
Spring return allows spray and hose to be pulled
down into the spraying position, and then retract
back to upright position when released, reducing
back flow risk from the trigger spray being
immersed in water
Adjustable wall bracket provides increased
support and stability to the riser assembly
Modular design allows easy configuration to suit
specific needs
Fast, easy installation, supplied with minimal
on-site assembly required
food service pre-rinse assemblies
product features

3 Call 1300 369 273 www.enware.com.au
FHS001 FHS011 FHS021 FHS031
FHS041 FHS101 FHS111 FHS121
FHS131 FHS141 FHA016 FHA116
FS760
FWS001 FWS011 FWS021 FWS031
FWS101 FWS111 FWS121 FWS121C
FWS121W FWS131 FS704 FS705
FSJ705 FWA016 FWA056 FWA116
FWA156
Hob
Mounted
Wall
Mounted
product codes

www.enware.com.au Call 1300 369 273 4
technical data
Water Inlet Connecon (Hot / cold)
1/2” BSP (DN 15mm)
5/8” BSP (In-wall recessed SBA)
Working Pressure Range
10-1200 kPa (Jumper valve, spring loaded valve)
50-800 kPa (Ceramic Disc)
Recommended Working Pressure Range* 150-500 kPa max*
Flow Rate Pre-rinse spray gun 4 L/min
Pot ller 8 L/min. supplied standard
Operang Temperature Range
0 - 95 °C (Jumper valve)
0 - 85 °C (Spring loaded valve, incl. pre-rinse spray gun)
0 - 75 °C (Ceramic Disk)
WATER SERVICES
Plumbing Code of Australia: Part B1 Cold Water
Services AS / NZS 3500.1-2003 Water Services;
• Secon 1.6(a) Facilies for people with Disabilies
• Secon 3.3.2 Pressure at outlets (min 50kPa)
• Secon 3.3.4 Maximum pressure within
buildings (500kPa stac)
• Secon 3.4 Velocity Requirement (Max 3.0m/s)
• Secon 16 Tesng and Commissioning; Flushing,
Hydrostac tesng, cleaning and disinfecon of
water services.
HEATED WATER SERVICES
Plumbing Code of Australia: Part B2 Heated Water
Services
AS / NZS 3500.4-2003 Heated Water Services;
• Secon 1.9 Water Temperature
1.9.1 Storage Temperature
1.9.2 Sanitary xtures delivery temperature
1.9.3 Acceptable soluons for control of delivery
temperatures
• Secon 10 Heated Water Services for People
with Disabilies
• Secon 11 Tesng and Commissioning
installation compliance
*Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA), AS/NZS3500
and the manufacturer’s instrucons.
Installaons not complying with PCA, AS/NZS 3500 or the manufacturer’s instrucons may void the product
and performance warranty provisions.
This product must be installed and commissioned by a qualied plumber. The following clauses must be
observed for a compliant installaon and correct operaon of Enware tapware.
For use with potable water only.

5 Call 1300 369 273 www.enware.com.au

• Ensure all operang and dimensional specicaons
are suitable for the intended installaon.
• Check that there is no shelf or obstrucon above.
Shorter riser, hose & spring guard opons are
available from Enware
• Check that wall bracket can be installed on a stable
wall surface. If not, extra measures may need to be
taken so that the bracket can be supported by a rm
wall backing.
•       
to remove debris prior to the installaon of this
product as per AS/NZS 3500.1. Strainers (40 mesh)
are recommended if debris is an ongoing problem.
• Ensure water pressures for hot and cold supplies
   If not, one side may
override the other. A pressure reducon valve
may be required to address any imbalance in
the water supply pressure, or to comply with the
recommended maximum pressure.
• It is recommended that isolaon valves are installed
on both hot and cold supplies prior to the pre-rinse
unit and that these are easily accessible.
Choose the type of base to be installed.
Unpack and layout all components to check that you have all parts.
Hob Mounted
Single Inlet
[FS011, FS010]
Wall Mounted Exposed
Breech [FS022]
Wall Mounted Single Inlet
[FS021, FS020]
Wall Mounted Recessed
(Concealed In-Wall) [FS023]
Hob Mounted
Twinner Body
[FS015]
Hob Mounted Exposed
Breech [FS012]
Hob Mounted
Concealed Breech
[FS013]
assembly and installation procedure
installation the base
GO TO PAGE 6
GO TO PAGE 11
GO TO PAGE 7 GO TO PAGE 8
GO TO PAGE 12
GO TO PAGE 9
GO TO PAGE 13

www.enware.com.au Call 1300 369 273 6
1. Fit 1/2” Tail into Base Mount:
Apply thread sealing tape onto the
non-beveled end of 1/2” BSP all-thread tail,
and screw to female thread of hob base.
2. Mark the hole to be drilled on the bench
(min. 40mm - max. 160mm to the centre
from wall) and drill the hole (Φ 22mm) using
a hole saw or similar tool.
3. For tap base with an-rotaon pins,
note the orientaon of the tap handle
(standard is either facing the front or to the
right hand side). Check the posions of the
two an-rotaon pins on the underside of
base. Mark the corresponding pin locaons
onto bench and drill 2x holes (Φ 9mm).
4. Fit base onto the bench and secure using
1/2” brass nut from underneath the bench.
For base with an-rotaon pins, t black
spacer rst (if required), then t the nut,
and ghten rmly. Do not over-ghten.
(Using excessive force may result in damage
to the black plasc spacer.) SEE IMAGE 5.
5. Proceed to installaon of riser, pot ller &
spray arm – page 15
IMAGE 1
IMAGE 4
IMAGE 2
Single inlet hob tap
assembly - Maximum
bench thickness: 35mm
Hob base mount -
Maximum bench
thickness: 10mm
9
22
33 mm
40 mm MIN -
160 mm MAX
WALL
9
IMAGE 3
IMAGE 5
hob mounted single inlet FS011 FS010

7 Call 1300 369 273 www.enware.com.au
1. Mark the hole to be drilled on the bench
(min. 40mm - max. 160mm to the centre
from wall) and drill a Φ33mm hole using a
hole saw or similar tool.
2. Unscrew metal washer and xing nut from
body assembly.
Fit one exible inlet hose onto body. Apply
a small amount of food grade grease onto
o-ring before ng. (Note markings on
exible hose – red [for hot] and blue [for
cold])
3. Fit base onto bench through the drilled
hole. From underneath the bench, t large
metal washer before ng the brass locking
nut. Hand-ghten locking nut. Check that
tap base is facing straight forward, then use
a Philips head screw driver to rmly ghten
the two screws on either sides of brass nut.
4. Fit the other exible inlet hose onto body.
5. Proceed to installaon of riser, pot ller &
spray arm – page 15
IMAGE 7
33
40 mm MIN -
160 mm MAX
WALL
IMAGE 6
IMAGE 8
IMAGE 10
IMAGE 9
Maximum bench
thickness: 30mm
hob mounted twinner body FS015

www.enware.com.au Call 1300 369 273 8
1. Mark 2x holes to be drilled on the bench.
(min. 40mm - max. 160mm to the centre
from wall, 215mm apart, or for adjustable
width models - min. 150mm, max. 330mm)
2. Drill the holes (Φ 22mm) using a hole saw or
similar tool.
3. Ensure the base cover domes and clear
washers are ed, and x base body onto
bench. From underneath the bench, t lock
nuts onto the tails and ghten rmly using a
spanner.
4. Proceed to installaon of riser, pot ller &
spray arm – page 15
IMAGE 12
22
22
215 mm
40 mm MIN -
160 mm MAX
WALL
(Adjustable Models:180 mm MIN - 330 mm MAX)
IMAGE 11
Maximum bench
thickness: 30mm
hob mounted exposed breech FS012

9 Call 1300 369 273 www.enware.com.au
1. Mark the holes to be drilled on the bench
and drill the holes. (min. 40mm - max.
160mm to the centre from wall, tap body
centres min. 150 mm – max. 300mm. Drill
hole size: spout – Φ 22mm, tap bodies – Φ
33mm).
Cut the copper T piece to size:
2. Screw 1x brass xing nut on each tap body
and screw the nut right down to the end of
thread.
3. Fit the bodies upside down into the 33mm
holes from top of the bench. Align centre
of the copper T piece to the centre hole.
Mark the copper pipes on both sides.
(19mm past the end of the body thread,
or deduct 15mm from the centre of drilled
hole on each side). Check the measurement
again, and cut the copper tube with
tube cuers. De-burr the copper tube.
Take tap bodies out of the holes and keep
at hand.
Fit the spout:
4. Pull the brass 1/2” threaded tail o the
copper T-piece. Apply thread sealant to the
non-beveled end of the 1/2” threaded tail,
then screw into the base of the swivel hob
and ghten.
5. Fit smaller clear washer through the 1/2”
tail, then t the base onto the bench. From
underneath the bench, t smaller red bre
washer onto the tail, then screw 1/2” brass
nut on. Note the orientaon of the grub
screw on the base, then ghten the brass
nut rmly using a spanner. SEE IMAGE 17
IMAGE 14 IMAGE 15
IMAGE 16
33
22
33
150 mm MIN - 300 mm MAX
40 mm MIN -
160 mm MAX
WALL
IMAGE 13
IMAGE 17
Maximum bench
thickness: 20mm
hob mounted concealed adjustable breech FS013

www.enware.com.au Call 1300 369 273 10

6. Fit compression nut and olive to each side of
the copper T-piece, and t tap bodies on to
each side. Screw each compression nut onto
each body loosely. Note: a small groove in the
spline of the spindle and red tape indicates
the hot side.
7. Check the 2 o-rings on the centre spout ng
of the T-piece has o-ring grease applied. Fit
larger red bre washers onto each basin body.
8. From underneath the bench, insert the tap
bodies and T-piece assembly up through the
bench, at the same me inserng the T-piece
up into the 1/2” brass tail of spout. Take care
not to pinch or damage the o-rings in the
process. Push the T-piece assembly unl it
comes to a stop. SEE IMAGE 18.
9. While holding the T-piece up, from top of the
bench t a clear plasc washer and a cover
dome onto each tap body. Screw the dome in
unl it comes in contact with the bench, but
do not ghten the dome at this point. Ensure
both tap bodies extend through the bench
the same distance. SEE IMAGE 19.
Now from underneath the bench, screw the
xing nuts back up hard against the bench and
ghten with a basin spanner. (Alternavely,
from top of the bench, gently ghten the
chrome cover domes with a spanner.)
SEE IMAGE 20 & 21
10. Now ghten the 1/2” compression nuts on
the T-piece with a spanner. Re-torque all
nuts and ensure they are ght.

11. SBA’s (spindles) should already be ed
onto tap bodies.
Fit the lever handles onto spindles. Note the
orientaon of the lever handle – facing the
front for closed posion, turning outwards
to open. The lever posion can be adjusted
by re-posioning the handle on the splines
of the spindle. The levers can also be set
slightly oset (away) from the spout when
in closed posion. SEE IMAGE 45 PAGE 18
12. Once the handle is correctly posioned, use
locking screw and washers to secure the
lever handle to spindle. Tighten using the
3mm Allen key provided, then t indicator
buon holder into the lever handle top by
pushing it
13. Proceed to installaon of riser, pot ller &
spray arm – page 15
IMAGE 18
IMAGE 19
IMAGE 21
IMAGE 23
IMAGE 20
IMAGE 22
IMAGE 25
IMAGE 24

11 Call 1300 369 273 www.enware.com.au
Rough In:
1. Secure two 1/2” BSP male ngs behind the nished wall, for hot
and cold water supplies, 150mm apart. Allow approx. 12mm of thread
proud from nished wall

2. Flush the line thoroughly before connecng tap ngs. Once the line
is clear of debris, proceed to next step.
3. Unscrew wall bases from the tap assembly.
4. Apply thread sealing tape onto the two 1/2” male threads on wall.
Seal any gaps between the thread and the wall with silicone sealant.
Screw each wall base onto each thread and ghten rmly. For extra
leverage, use a half inch (1/2”) Allen key through the centre hole.
SEE IMAGE 28.
5. Check that the tap frame has two o-rings on the spigot ng on each
side. Check that they are lightly greased with food grade o-ring grease.
6. Gently but rmly push the frame onto the wall bases, making sure the
o-rings are not pinched, dislocated or damaged in the process.
7. Once the tap frame has fully engaged, screw each nut onto wall base
and ghten with a spanner.
8. Proceed to installaon of riser, pot ller & spray arm – page 15
IMAGE 28
IMAGE 27
150
IMAGE 29
wall mounted exposed breech FS022

www.enware.com.au Call 1300 369 273 12
wall mounted single inlet FS021 FS020
Rough In:
1. Secure one 1/2” BSP male ng behind the nished wall, allowing
approx. 12mm of thread proud from nished wall.

2. If required cut the 1/2” thread on wall so it is approx. 12mm proud
from nished wall.
3. Flush the line thoroughly before connecng tap ngs. Once the line
is clear of debris, proceed to next step.
4. To t wall base mount, apply thread sealing tape onto the 1/2” BSP
male thread on wall. Seal any gaps between thread and wall with
silicone sealant. Screw wall base onto the 1/2” thread, and ghten
rmly. Make sure the wall base is ed plumb (facing straight up).
5. Proceed to installaon of riser, pot ller & spray arm – page 15

13 Call 1300 369 273 www.enware.com.au
Rough In:
1. Secure a tap breeching piece behind wall, seng
the face of the body within 1 to 14mm behind
nished wall, and outlet 1/2” BSP male ng
approx. 12mm proud from the nished wall.

2. Before proceeding check that the wall tap body
to nished wall surface is within the standard
ange adjustment range (1 – 14mm for 1/4 turn
jumper valve). Installaons outside of this range
may require extended SBA’s (spindles) or trouble
domes (available from Enware). SEE IMAGE 30
3. Flush the line thoroughly before connecng tap
ngs. Once the line is clear of debris, proceed to
next step.

4. Fit wall base onto the 1/2” thread male outlet.
SEE IMAGE 31. Refer to previous secon - Wall
Mounted Single Inlet Model installaon procedure
on Page 12.
5. The SBA must be installed separately to the dress
ngs. Firstly pull the indicator buons out,
remove ange and lever handle assembly from the
SBA. SEE IMAGE 31
Note that the SBA marked with a small groove in the
spline indicates cold SBA (in-wall).
6. Remove the blue or red plasc protecng cap from
SBA.
Check that tap washer and red bre washer are located
in their correct posions, and screw the SBA onto tap
body in wall. Tighten the SBA using a tube spanner or
other appropriate spanner by the hexagonal ats near
the base (not by the smaller hexagonal gland nut in
the middle near the spindle). Recommended torque
seng is 30Nm
IMAGE 31
(From 1mm behind finished wall to 14mm behind finished wall)
A
Finished Wall
Recess Body (A = 1mm )
MIN
B
Finished Wall
Recess Body (B = 14mm )
MAX
IMAGE 30
wall mounted recessed (concealed in wall) FS023

www.enware.com.au Call 1300 369 273 14
Test for leaks from SBA’s:
7. Turn o the SBA’s using the lever handle, then turn
water supply on. Turn the tap on and o a few
mes to test for leaks from SBA’s. (Cover the outlet
with a towel to minimise water splashing.)
8. Once water-ghtness is conrmed, seal gaps
between the SBA’s and the wall with silicone
sealant or other appropriate sealant.
Fit Flange & Handle:
9. Hand-ghten the recess wall ange onto thread
of SBA unl it comes to a rm stop against the
wall.
10. Place the lever handle onto the spindle. The
lever posion can be adjusted by re-posioning
the handle on the splines of the spindle. Most
applicaons require the lever to sit poinng
straight up or slightly oset (away) from the
spout.
11. When correctly posioned use locking screw
and washers to secure lever handle to spindle.
Tighten using the Allen key. Push the indicator
buon holder into the lever handle top.
12. Proceed to installaon of riser, pot ller & spray
arm – page 15
IMAGE 31

15 Call 1300 369 273 www.enware.com.au
Note that each component of the pre-rinse assembly uses a corresponding male-double-o-ring-spigot to female-socket
swivel connecon. The o-rings on the male spigot are pre-greased. Re-grease them if required.
1. Take grub screws out from female joints of all parts (riser,
pot ller adaptor, base, body) and keep them at hand.
2. Fit riser and/or pot ller adaptor onto the base body. To
do this, rstly align the joints straight, then gently but
rmly push the male double o-ring spigot ng into the
female connecon, taking care not to pinch or damage
the o-rings while doing so. Push the joints together all
the way unl the male joint comes to a stop.
3. Check that the riser is sing plumb (straight up). Measure
the distance between the wall and the riser.
4. Assemble the wall bracket, making sure that there is
enough thread going into the wall plate and the half
secon of the riser bracket. Note the dierence in length
from the measurement taken in step 3. Cut the all-thread
to suit (if required).
5. Re-assemble the bracket, and t the bracket onto the
riser as high up as possible. This gives greater support
and stability to the assembly. Gently ghten the two
screws of the bracket onto riser using the 2.5mm Allen
key provided.
installing the riser, pot filler & spray arm
IMAGE 35
IMAGE 35
IMAGE 36
IMAGE 33 IMAGE 34
IMAGE 32

www.enware.com.au Call 1300 369 273 16
6. Check that the riser is sing plumb both ways (front-
rear, right – le), and bracket is lined up straight towards
the wall. Then mark the two drill holes of the bracket on
the wall.
7. Drill the two marked holes in the wall and x the bracket
onto wall using appropriate xings.
8. Fit spring retainer/ hose/ spray gun assembly onto riser.
9. Fit all grub screws back onto ngs, using the 2.5mm
Allen key provided. Check that each grub screw has
engaged into the recess of the male spigot, then ghten
gently.
Before fully ghtening the grub screw, check that the pot
ller is facing the preferred direcon. (If spout needs to
swivel, ghten grub screw and then back o slightly just
enough for the spout to swivel. Do not disengage screw
more than half a turn. If grub screw is not ed correctly
it may result in premature wear or damage to the brass
spigot.)
Ensure the spigot has engaged into the socket
properly. SEE IMAGE 39, 40
Ensure the grub screw has engaged into the groove
properly. SEE IMAGE 41, 42
IMAGE 37
IMAGE 39
IMAGE 41
IMAGE 38
IMAGE 40
IMAGE 42
7
TYP
50 P.C.D.
INSTALLATION DETAIL
(WALL BRACKET CUTOUT)

17 Call 1300 369 273 www.enware.com.au
1. Ensure the hot and cold supply lines have been ushed thoroughly to remove debris.
2. Once the lines are clear of debris, connect tap to water supply.
(For taps with exible hoses: care must be taken to not twist or kink the exible hose. If the isolaon tap is located
in an awkward posion or is too far, use another ng and a exible hose to extend the length and to reduce the
strain on the exible hose)
3. Check again that all screws, nuts, grub screws and ngs have been ed and ghtened.
4. Check that all taps and the trigger spray are turned o.
5. Turn water supply on to check for leaks at all connecon points.
The tap is now ready for use.
water connections
WARNING Hot water will scald. Care must be taken to avoid scalding when using the trigger spray to
deliver hot water. Exposed metal secons of the mixer, riser assembly, hose connecons and trigger spray
may become hot when in use and may cause burn injuries.
When not in use ensure all taps to the pre rinse assembly are turned o. The taps should not be le on
when unaended as this maintains pressure to the hose and trigger spray assembly, which could result in
water damage from ooding if in the unlikely event the hose or trigger spray were to malfuncon.

www.enware.com.au Call 1300 369 273 18

Squeeze spray trigger and pull down hose to
desired angle and posion to wash.
SEE IMAGE 43
To make the spray stay on, slide the holding
ring over the trigger. SEE IMAGE 44
To turn o, let go of the trigger or slide the
holding ring o the spray lever handle.
Use the hook to stow away the spray gun
OPERATING LEVER TAPS
To operate taps, turn handle lever in the
direcons indicated: either pulling forward and
down toward the user, or turning outwards to
open. SEE IMAGE 45
operating instructions
cleaning
IMAGE 43
IMAGE 45
¼ Turn Contra-Rotating Handles
O
On
O
On
O
On
O
On
Bench Mounted Mixing SetWall Mounted Mixing Set
IMAGE 44
Enware Product should be cleaned with a so damp cloth using only mild liquid detergent or soap and water. Do not
use cleaning agents containing a corrosive acid, scouring agent or solvent chemicals. Do not use cream cleaners, as they
are abrasive. Epoxy coated surfaces should only be cleaned with a cloth and clear water or mild detergent.
Use of unsuitable cleaning agents may damage the surface. Any damage caused in this way will not be covered by
warranty.

19 Call 1300 369 273 www.enware.com.au
components and spare parts
Ultra-Rinse Pre-Rise Trigger Spray (Standard) FS729
Ultra-spray so rinse trigger spray (Non-adjustable spray outlet) FS729SS
Trigger spray spring loaded SBA (cartridge) FS721S
Trigger Spray Service Kit FS077NS
Trigger Spray Handle & Screw FS790
O-rings (8), grub screws (4), & aerator (1) pack FS734
Check valves (2 in pack) MIS631
Lever Indicator buon (hot, cold, warm) & xing screw FS092 (Hot), FS093 (Cold),
FS094 (Plain)
Lever handle xing screw and washer MIS597
Lever handle with indicator buon (specify hot, cold, or plain) FSJ378
Lever Top Assembly (includes handle, indicator buon,
xing screw & washer, SBA)
Hob Mount (Pillar / Bib) - FSJ095 (Hot),
FSJ096 (Cold & Pot Filler)
Hob Mount with Flange (Basin / Sink) -
FSJ391 (Specify Hot or Cold)
Wall Mounted - Recess Adaptor - FSJ308
(Specify Hot or Cold)
Food service SBA (spindle)
Hob Mount (Pillar / Bib) FSJ381 (Specify Hot
or Cold)
In-Wall - FSJ395 (Recess - Cold),
FSJ396 (Recess - Hot)
Tap washers (Hydroseal - pair) MIS630
Flexible hose (hot, cold) MIS632 (Cold/Blue), MIS633 (Hot/Red)
Wall bracket FS070
Heavy Duty Hose
FS104 (400mm), FS106 (600mm), FS109
(900mm), FS110 (1000mm -Standard), FS111
(1100mm), FS115 (1500mm)
Riser FS051 (100mm), FS053 (300mm), FS056
(600mm), FS059 (900mm)
Pot ller adaptor FS063
Spring Retainer
(retainer ng only, for spring, hose and hook) FS061
Trigger Spray Hook FS072
Spring Guard (Exterior Spring Guard Stainless Steel 316 Grade) FS100 (585mm Standard), FS101 (385mm
Short)
Scker Label - Lever Tap Operaon MIS620
For more informaon, go to our website - www.enware.com.au, enter product code in search keyword.