enware WELLBEING Series Installation and operating instructions

Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: [phone] Fax: [phone]
NOTE: THIS DOCUMENT IS TO BE LEFT ONSITE WITH FACILITY MANAGER AFTER INSTALLATION
WELLBEING SERIES
I00077_Oct 17
Installation & Maintenance Instructions
SEQUENTIAL SHOWER MIXER
BASIN / SINK SET
WALL TOP ASSEMBLY
DUAL MIXER /
SEQUENTIAL BASIN MIXER

www.enware.com.au Call 1300 369 273 3
Working Pressure Range 50-800 kPa
Recommended Maximum Pressure 500 kPa*
Working Temperature Range 5 °C – 85 °C *
compliance
*Enware products are to be installed in
accordance with the Plumbing Code of Australia
and AS/NZS3500.
Reference should also be made to the Australasian
Health Facility Guidelines (AHFG), ABCB and Local
Government regulaons when considering the
choice of, and the installaon of these products.
Thermostac Mixing Valves and Pressure
Reducon Valves may be required to comply
with maximum temperature and pressure
requirements.
please note
Enware Australia advises due to ongoing Research
and Development, specicaons may change
without noce.
Component specicaons may change on some
export models.
before installation
Before Proceeding With Installaon
• Ensure all operang & dimensional
specicaons are suitable for the intended
installaon.
• Ensure all supply lines are ushed thoroughly
to remove debris prior to the installaon of
this product as per AS/NZS 3500.1. Strainers
(40 mesh) are recommended if debris is an
ongoing problem.
WELLBEING SERIES
Installation & Maintenance Instructions
technical data
For use with potable water only.

4 Call 1300 369 273 www.enware.com.au
WALL TOP ASSEMBLY
installation
WBWTCD65-LTC | WBWTCD65-RTC
80 min.
100 max.
20 ADJ.
65
G5/8" (BSP
)
CLOSED
OPEN
CLOSED
OPEN
RECESS BODY
MAX 18 mm
MIN 0 mm
FINISHED WALL
LTC an-clockwise to close | RTC clockwise to close
* For deeper wall recess use extended
SBA (Max. 33 mm)
Wall Depth Adjustment

www.enware.com.au Call 1300 369 273 5
6
MAX 18Nm
1
MAX 30Nm
2
3
“CLICK”
4
5

6 Call 1300 369 273 www.enware.com.au
SEQUENTIAL SHOWER MIXER
installation
WBSHSQ65
65
105 max.
25 ADJ.
50
50
G1/2" (BSP)
FEMALE OUTLET
Ø75
CLOSED
FULL COLD
FULL WARM

www.enware.com.au Call 1300 369 273 7
FINISHED WALL
MIN 50mm
MAX 75mm
1000mm
FROM FLOOR
NOGGING
POSITION
x shower into posion
7
1 2
34
“CLICK”
65
OFF POSITION

8 Call 1300 369 273 www.enware.com.au
DUAL MIXER
SEQUENTIAL BASIN MIXER
B
A
OPEN
CLOSED
CLOSED
FULL COLD
FULL WARM
A
B
installation
WBDMCD65-165 | WBDSQ65-165
Ø55
65
Ø55
65
Ø55
65
Ø55
65
A B
165 Spout 165 215
220 Spout 220 230

www.enware.com.au Call 1300 369 273 9
7
35
BENCHTOP CUTOUT
87
57
Cut tap hole on bench, with clearance around
tap hole for spacer stabilizer
1 2
34
56spacer stabilizer must be used for
bench thickness less than 10mm
SPACER STABILIZER
Cut tap hole on bench, with clearance
around tap hole for spacer stabilizer

10 Call 1300 369 273 www.enware.com.au
BASIN/SINK SET
installation
WBBCD65-165
150 - 300
(CUT TO SUIT ON SITE)
G1/2" (BSP) WITH OLIVE
COMPRESSION FITTING
65
8020 max.
165
165
Ø55 TYP
OPEN OPEN
CLOSEDCLOSED
Ø33
2 x body
cutout
Ø22
1 x spout
cutout
1 2
cut holes to suit outlet
and handle posions

www.enware.com.au Call 1300 369 273 11
109
CU
T
CUT
3
THREAD
SEALANT
4
56
7
“CLICK”
2X
8

12 Call 1300 369 273 www.enware.com.au
7
5
6
3
2
9
1
8
11
12
10
4
13
14
15
1 Red Fibre Washer 9 SBA Locknut
2 Spline Adaptor Octagon Insert 10 Handle Base
3 Dome 11 Handle 65mm Insert
4 O-Ring 12 Indicator –Red
5 Washer – S/S 13 Fricon Bush
6 Washer – Nylon 14 Indicator – Blue
7 Screw M5x20 S/S 15 Indicator - Yellow
8 SBA Spindle Q/Turn 80mm
WALL TOP ASSEMBLY parts WBWTCD65-LTC | WBWTCD65-RTC

www.enware.com.au Call 1300 369 273 13
1
2
3
11
12
4
5
10
9
6
7
8
1 Shower Mixer Body 7 Washer – S/S
2Sequenal Mixer Cartridge - 180° 8 Screw M5 x 35 S/S
3 Cartridge Retaining Nut 9 Handle 65mm Insert
4 Spline Adaptor Octagon Insert 10 Indicator – Grey
5 Handle Base 11 Dress Ring – Shower
6 Washer - Nylon 12 Colour Indicators
SEQUENTIAL SHOWER MIXER parts WBSHSQ65

14 Call 1300 369 273 www.enware.com.au
2
3
4
5
1
17
14
15
18
19
26
16
6
8
7
12
10
9
21
13
11
23
20
22
24
25
27
1 Dual Mixer Body 15 O-Ring
2 Spout 16 Hose 350mm Blue
3Fricon Brush 17 Fixing Bolt M6x80
4 Spout Fixing Insert 18 Fixing Plate Washer Nitrile
5 Grub Screw M5x15 19 Fixing Plate Brass
6 SBA Spindle Q/Turn 55mm RTC 20 Handle Base
7 SBA Locknut 21 Handle 65mm Insert
8 Red Fibre Washer 22 Indicator – Red
9 Washer – S/S 23 Indicator – Blue
10 Washer – Nylon 24 Indicator - Yellow
11 Screw – M5x20 S/S 25 Hose 350mm Red
12 Spline Adaptor Octagon Insert 26 Fixing Nut M6x42
13 SBA Spindle Q/Turn 55mm LTC 27 Mixer Plasc Spacer Stabilizer
14 Dress Ring – Hob Mixer Base
DUAL MIXER parts WBDMCD65-165

www.enware.com.au Call 1300 369 273 15
2
4
5
3
1
16
17
9
6
7
8
11
12
20
23
15
13
14
21
10
19
1822
24
1Sequenal Mixer Body 13 Dress Ring – Hob Mixer Base
2 Spout 165mm 14 O-Ring
3 Grub Screw M5x15 15 Hose 350mm Blue
4Fricon Bush 16 Fixing Plate Washer Nitrile
5 Spout Fixing Insert 17 Fixing Plate Brass
6Sequenal Mixer Cartridge - 90° 18 Handle 65mm Insert
7 Cartridge Retaining Nut 19 Indicator – Grey
8 Spline Adaptor Octagon Insert 20 Screw M5x35
9 Colour Indicators Mixer Body 21 Fixing Bolt M6x80
10 Handle Base 22 Hose 350mmm Red
11 Washer – Nylon 23 Fixing Nut M6x42
12 Washer – S/S 24 Mixer Plasc Spacer Stabilizer
SEQUENTIAL BASIN MIXER parts WBBSQ65-165

16 Call 1300 369 273 www.enware.com.au
1 Dress Ring – Hob Spout 12 Dome
2 O-Ring 13 Washer – S/S
3 Spout Base 14 Washer – Nylon
4 Spout 165mm 15 Screw M5x20
5 Spout Fixing Insert 16 SBA Spindle Q/Turn Contra 55mm
6 Grub Screw M5x12 17 Handle Base
7Fricon Bush 18 Handle 65mm Insert
8 SBA Spindle Q/Turn 55mm 19 Indicator – Red
9 SBA Locknut 20 Indicator – Blue
10 Red Fibre Washer 21 Indicator – Yellow
11 Spline Adaptor Octagon Insert 22 Basin / Sink Tee Kit
BASIN MIXER parts WBBCD65-165
4
7
5
6
3
1
12
14
13
15
16
8
10
9
11
2
17
18
20
19
2
22
21

www.enware.com.au Call 1300 369 273 17
PROBLEM CAUSE RECTIFICATION
Water leaking from outlet
Water dripping and does not
shut o
Debris caught in seal of
cartridge or SBA
Remove cartridge/SBA and
inspect. Remove debris
and/or replace cartridge/SBA if
damaged
Ceramic discs are worn or
damaged
Replace SBA/cartridge
Tap seat is damaged (for SBA
only)
Refurbish tap seat using a
reseang tool. If necessary - t
reseang kit.
Water is leaking from spindle O-ring on SBA/Cartridge is
worn or damaged
Replace SBA/Cartridge
Water is not owing from tap
Poor water ow from outlet
Water turned o. Turn water on.
Aerator or Flow control is
blocked by debris.
Remove tap and wash debris
from aerator/ow control.
Install an inline strainer.
Handle is wobbly
Handle feels loose
Spline adaptor (octagon insert)
is missing
Ensure spline adaptor is
installed correctly
Handle does not align perfectly
straight
Due to handles being spline mounted, handles may be oset slightly
from vercal or straight. This is normal and unavoidable
Wall ange does not screw into
thread of SBA
Tap bodies are set too far into
the wall
Use extended recess spindle
(SBA only)
Wall ange does not screw
down onto wall surface
Tap bodies are set too far out Use a trouble dome or ange
extender
TROUBLESHOOTING

18 Call 1300 369 273 www.enware.com.au

www.enware.com.au Call 1300 369 273 19
SERVICE & MAINTENANCE
spout & tap handles
Occasionally the handle screws should be checked
for ghtness and a visual inspecon made of all other
connecons on the tap assembly. Ensure that the
spout and the tap handles are secure, and ghten if
necessary.
sequential mixer cartridge
To replace mixer cartridge, unscrew cartridge
retaining nut with Enware Cartridge Key (WBSQKEY).
Pull cartridge out and replace with new component.
Fit cartridge retaining nut back on, and ghten
using Enware Cartridge Key. Do not overghten.
(Recommended - 20Nm)
aerator
Spout aerator should be checked periodically for
debris. Use Aerator Key to unscrew spout aerator. If
aerator doesn’t come out completely, turn tap on to
ush the aerator out.
Inspect and reverse rinse aerator to clear any debris.
Replace aerator if necessary.
To t aerator back, insert aerator into p of spout
using care to avoid damage to the aerator O-ring by
ensuring the aerator is square to the spout outlet, and
nger ghten half a turn. Use Aerator Key to ghten
aerator into posion. Do not overghten.
cleaning
Enware Product should be cleaned with a so damp
cloth using only mild liquid detergent or soap and
water.
Do not use cleaning agents containing a corrosive acid,
scouring agent or solvent chemicals. Do not use cream
cleaners, as they are abrasive. Epoxy coated surfaces
should only be cleaned with a cloth and clear water or
mild detergent. Use of unsuitable cleaning agents may
damage the surface. Any damage caused in this way
will not be covered by warranty.

20 Call 1300 369 273 www.enware.com.au
PART ENWARE PRODUCT CODE
Handle Assembly
(Includes Blue, Red, Yellow colour
indicators)
WB65
Handle Colour Indicator Pack
(Blue, Red, Yellow)
WBIND
Colour Indicator Pack
(For Sequenal Mixer)
Grey handle indicator, 4 colour
indicators for body
WBSQIND
Wall Top Assembly
Handle Assembly + Dome+ SBA
Ceramic Disc
RTC (Clockwise to Close)
LTC (An-Clockwise to Close)
WBWTCD65-LTC
WBWTCD65-RTC
SBA Ceramic Disc - Hob
RTC (Clockwise to Close)
LTC (An-Clockwise to Close)
WBBCDSBA-LTC
WBBCDSBA-RTC
SBA Ceramic Disc - Recess Wall
80mm
RTC (Clockwise to Close)
LTC (An-Clockwise to Close)
WBWCDSBA-LTC
WBWCDSBA-RTC
SBA Ceramic Disc - Recess Wall
95mm (Extended 15mm)
RTC (Clockwise to Close)
LTC (An-Clockwise to Close)
WBWCDSBA15-LTC
WBWCDSBA15-RTC
Sequenal Mixer Cartridge
(90° RTC - Sink / Basin Mixer)
WBSQSBA
Sequenal Mixer Cartridge
(180° RTC - Shower Mixer)
WBSQSHSBA
Spline Adaptor for SBA
WBCDOCT (Wall/Hob)
WBDMCDOCT (Dual Mixer)
WBSQOCT (Sequenal Mixer)
Dome – Basin/Sink/Wall WBCDFLAN
SPARE PARTS