EPOS Magnum User manual

E -P os Magnum
Us er Manual

TABLE OF CONTENTS
Introduction -1
Table of Contents -3
Location -4
Do’s & Don’ts -5
Accessories -6
General Information -7
Specifications -8
Jumper Settings -11
Connectors -14
Hardware Installation -15
Software Driver Installation -20

LOCATIONS
Corporate Head Quarters
Middle East
E-PoS International
LLC
P.O.Box 12608
Dubai, UAE
Tel: +9714-3523288 / 3512861
Fax: +9714-3513396
Email:
eposintl@emirates.net.ae
South East Asia Head Quarters
South East
Asia
E-PoS International
Nasik-Pune Road
Ayodhya Nagri
Nasik, Maharasthra
India
Tel: +91-253-2411806
Fax: +91-252-2415295
Email:
pradeepw@sancharnet.in

DO’S & DON’TS
(Integrated circuits on All E-PoS System boards are sensitive to static electricity.
To avoid damaging any Components on the computer board, before getting
started, read these following precautions and other instructions and save them for
later reference).
i. Do not remove the computer from the anti-static Packaging until you are ready for
installation.
ii. Make sure the voltage of the power source is correct before connecting the
computer to the power outlet, (110~220 volts).
iii. Connect Rubber Legs provided to avoid damaging Cabinet Cover and Door,
(where provided).
iv. Do not change any Hardware Devices online when System or the device is on and
running, because the sudden surge of power may ruin any sensitive components.
Also make sure the computer is properly grounded.
v. Turn off the computer before cleaning. Always clean with a damp or dry cloth
only. Do not spray any liquid cleaner on screen directly.
vi. The power outlet socket used to plug in the computer power cord must be located
near the system and easily accessible. Do not use outlets on the same circuit of the
system that regularly switch on and off.
vii. If the computer is sharing an extension cord with other devices, make sure the
total ampere rating of the devices plugged into the extension cord does not exceed
the cord’s ampere rating.
viii. Do not expose the power cord, extension cord and power outlet to moisture.
ix. The openings on the computer enclosure are for the cabin ventilation to prevent
the computer from overheating. DO NOT COVER THE OPENINGS.
x. Do not connect any devices to Powered COM Ports (5V/12V), other then the
devices that take power from Powered COM Ports to avoid damaging the Device.
xi. Any Hardware upgrades or changes to be made are to be informed, and do not
tamper with Serial Nos. and Warranty Seals, to avoid Warranty Void.
xii. If the computer is not equipped with an operating system. An operating system
must be loaded first before installing any software into the computer.
xiii. If the computer is equipped with a touch panel, avoid using sharp objects to
operate the touch panel. Scratches on the touch panel may cause mal-calibration
or non-function to the panel.
xiv. The LCD panel display is not subject to shock or vibration. When assembling the
computer, make sure it is securely installed.
xv. Choose an Ideal dust free location and reliable surface for the System with proper
ventilations.

ACCESSORIES
1. Warranty Card.
2. Power Cable.
3. Driver Bank CD.
4. CD Connection Kit.
5. PC Stand (4 Pcs).
6. Modem Cable (Optional)

General Information
__________________________________________________
The E-POS MAGNUM is an Intel Celeron / Pentium III (Socket
370) Multimedia ATX motherboard with LCD/VGA controller, Ethernet 100/10,
AC97 sound, and IDE flash disk. By integrating single chip, SiS630ST, the
E-POS MAGNUM provides a high performance / low cost desktop solution.
Highly integrated, the E-POS Magnum can adapt Intel. Celeron
(66MHz) and Pentium III (100/133MHz) CPU. Onboard features include four
serial ports, two multi–mode Parallel ports, a floppy drive controller and a PS /
2 keyboard PS / 2 mouse interface. The built-in high speed PCI IDE controller
supports both PIO and ATA 100 mode. Up to four IDE devices can be
connected, including large hard disks, CD-ROM drives and other IDE devices.
The full PC functionality coupled with its multi-I/Os stand ready to
accommodate a wide range of PC peripherals. Compact in size and with its
highly integrated multimedia and networking functions, the E-POS Magnum is
the most powerful PC engine to build any small footprint all-in-one PC system
for integration into any space-constricted embedded applications. Fully
configurable and with its modular design, the E-POS Magnum is an ideal
platform for any consumer computing applications where space is a premium.

Specifications
__________________________________________________
E-POS MAGNUM:
Multimedia I nt el Celeron/Pentium III FLEX AT X Motherboard wi t h
XGA, LCD, TV- out, Dual display, Ethernet & Audio I nter face
CPU:
I ntel S ocket 370
I ntel T ualatin FCPGA up t o 1 . 26GHz
I ntel Pentium III FCPGA 66/100/133 up t o 1 GH z
Celer on FCPGA 66/100 up to 1 . 3 GH z
Main Chipset: SiS630ST
Super I/O:
Winbond W83697HF & W83627F
• W83697HF: UART1, UART2, Parallel Port 1 FDC, Game/MIDI ,
I R/CI R, Hardware Monitor
• W83627F: UART3, Parallel Port 2, UART4 (Pin 1/9 power
s uppor t )
System BIOS: Award PnP Flash BI OS
System Memory:
2 x 168 pin DI MM s ock et s suppor t i ng S DR AM up to 1 GB
L2 Cache: CPU built-in
Standard I/O
• S er ial ports x 4: COM 1 ~ 4, COM 2 & 4 with + 5V/12 power
output on pin # 9
• Par allel port x 2: Suppor t S PP/EPP/ECP;
• AT A 100/66 I DE x 2: suppor t s up to 4 I DE devices
• FDD x 1: suppor t s up to 2 floppy disk drives
• PS /2 Keyboard I nt er face x 1
• I nter nal Keyboard I nt er face x 1
• PS /2 Mouse I nt er face x 1
• US B Interface x 4: 2 internal and 2 external

• GAME/MI DI port
Ethernet
• 100/10 Base-T Ethernet with RJ- 45
Display
• LCD controller
• I ntegr ated 2 D/3 D graphics engine, 4X AGP
• S har e s ys tem memory architecture able to ut il i z e the dis pl ay
memor y size up to 64MB
• Max imum resolution for video chi ps et: 640x480, 800x600,
1024x768, 1280x1024, 1600x1200, and 1920x1200, true- color
• S uppor t i ng L CD/VGA dual display mode
(Under Windows 98 and Wi ndows ME)
2nd Display Board (optional):S iS 301
• S uppor ting VGA/L CD (panel link) or VGA/TV or VGA/VGA,1
among 3
• LCD: Digital flat panel, suppor t i ng panel link
• Video: S- Video or RCA
• When the 2 nd dis play is installed, the pr i mar y display will be
changed t o VGA onl y
Audio Function
• Full duplex and i ndependent sample r ate conver t er for audio
r ecor ding & playback
• S uppor ts Microsoft DirectS ound
• 3D positional audio effects
• Hi- per for mance, mixed- s ignal, stereo
• MI C- I n, Speaker- Out, Line- I n
• Pin header for CD-audio i n
Hardware Monitor
• Monitor ing pr ocessor & s ys tem
• Monitor ing 5 VS B , VBAT, 1.5V, 3.3V, + 5V, + 12V, -12V, and
pr oces s or voltages
• Monitor ing pr ocessor, chassis fan speeds
• Contr olling pr ocessor and chas s i s fan speed and failure al ar m
• Automatic f an on/off control
• Read back capability that dis plays temperature, voltage and fan
s peed

• S uppor t i ng I ntel processor thermal diode output (real processor
temper atur e)
• Watchdog ti mer ( 64 level time i nt er v al s )
• Digital I N x 2 Digital OUT x 2
Expansion Bus: PCI * 1 & AMR* 1
Power: AT X power
Form Factor: FLEX AT X
Dimension: 229* 191 mm (9“x7.5”)
*Specifications are subject to change without notice.

JUMPER SETTINGS
_____________________________________________________________________________
T he E - POS Magnum is configur ed t o mat ch the needs of
s pecific appl i cati on by proper jumper settings. The onboar d
Connectors link the E - POS Magnum to ex ter nal devices such as
a har d di s k , a f l oppy disk or a pr i n t er . The following fi gur e hel ps
you to l ocate all jumpers and connectors.

T he following figur e s hows the l ocat i on of the r ear side
Connectors.

T he t abl e bel ow lis ts the f unct i on of each jumper. The
Coming s ect ions indicate how to s et jumpers to confi gur e the E - POS
Magnum. They also indicate the E - POS Magnum’s default
configur ation and opt i ons for each j umper.

JP4: COM2/COM4 Pin9 Power selection
JP5: Clear CMOS
Connectors
__________________________________________________

T he t abl e bel ow lis ts the f unct i on of each connector on the E-
Pos Magnum. Their corresponding pi n ass ignments will be s hown in
the following s ecti ons .

Expansion Slot
•PCI Slot
•AMR Slot (Audio Modem Riser slot)
•DI MM 1 , DIMM 2
HARDWARE INSTALLATION
_________________________________________________________________________
PS/2 Mouse Connector
T he PS /2 Mouse a 6 - pin female connector.

PS/2 Keyboard Connector
T he connector is for a s t andar d k ey boar d us i ng a PS / 2 Plug. For
s tandar d AT keyboard pl ug, a AT - PS /2 adapter is needed for the
connection.
Ethernet Connector
T he E - Pos Magnum features with a 3 2 - bit PCI - bus Ethernet
I nter face wi t h RJ- 45 connector. This high performance L AN
inter face i s suppor t ed by all major network operating s ys tems .
T her e ar e two L E D’s indicating the net wor k i ng s t atus .

USB Connectors
T he E - Pos Magnum provides two ex ter nal USB (Universal S erial
Bus ) ports to connect to U S B devices. It also pr ovi des two i nter nal
US B interface for more U S B device connection. The two i nter nal
US B interfaces have to be accessed t hr ough the 8- pin CN4.
Parallel Port Connector
T he E - Pos Magnum provides a 2 5 - pin female ex ter nal parallel
connector (LPT1). It also pr ovi des a 2 6 - pin internal parallel header
connector (LPT2). If the 2 nd par allel port is needed, a 26- pin to 25-
DUB parallel cable i s provided to connect LPT 2 for parallel device
connection.
Serial Port Connector
T he E - Pos Magnum provides four onboard s er i al ports for
connection to any serial devices such as card r eader , touch screen
and fax modem. COM 1 is a 9 -pin male ex t er nal serial connector
(COM1). COM 2 , COM 3 and COM 4 are 10- pin internal serial header
connector s . 10- pin to 9 - DUB serial cables are pr ovi ded t o connect

I nter nal COM por t s for more s er i al device connection. COM 4 is
equipped wi t h + 5V/12V power output on pin 1 and pi n 9. For COM 4
power setting,
CRT VGA Connector
T his connector is for output to a VGA compat i bl e devi ce.
Game/MIDI Connector
T he game/MI DI is a gol d 15- pin connector. The us er can connect
game j oy s t i ck s or game pads to thi s connector for playing computer
games .

Audio Connectors
T he E - Pos Magnum’s audio connectors include Speaker-out, Line in
and MIC-in. The s peak er - out is to out put the audi o to ex t er nal
devices such as speakers or earphones. The line- in is used t o input
audio fr om an external audio device s uch as a CD player, tape
r ecor der or a r adi o. The m i cr ophone- in is used t o connect to an
ex ter nal microphone to r ecor d s ound or voice.
ATA 100/66 IDE Connectors
T he E - Pos Magnum provides 2 40- pin I DE header connectors able
to s uppor t up t o 4 IDE devices. I t also pr ovides a AT A 1 0 0 /66 I DE
har d di s k ribbon cable and a 40- pin to 40 pin I DE cable for IDE
device connection. If two I DE drives are us ed, the s econd dr i v e
mus t be confi gur ed t o S l ave Mode by setting i ts jumpers
Accor dingly. You can configure t wo har d di s k drives to be both
Mas ter s with two I DE cables, one for primary I DE and t he other
for secondary I DE connector.
FDD Connector
T he E - Pos Magnum provides a 34- pin header type connector (FDC),
able to att ach two fl oppy dr ives . A 34-34- r ibbon cable i s needed to
connect the onboar d F DD to fl oppy disk drives.

SOFTWARE & DRIVERS INSTALLATION
T he chapt er introduces the Magnum onboard VGA, Ethernet,
Audio and t he r es pect i ve dr i v er s and i ns tallation.
Ethernet Drivers
T he MAGNU M pr ov i des a 10/100 Base T fast Ethernet. The MAGNU M
Ether net drive di s k ette or CD diskette cont ai ns the f ol l owi ng
dr iver s ;
S iS 630S T Ethernet drivers for
Windows 95/95OSR2
Windows 98/98S E
Windows 2000
Windows ME
Windows NT
Windows NT 4.0
Windows XP
AGP XGA Drivers
By integrating an advanced har dwar e 2 D/3 D GUI engine and 64-bit
gr aphic di s pl ay interface, the MAGNU M can deliver AGP 4X
per for mance and memor y bandwidth of up to 1 GB . It adopts Share
System Memory ar chitectur e, which can flexibly utilize the fr ame
buffer size up t o 6 4 MB . In addi t i on to pr oviding s tandar d i nter face
for analog moni tor , the MAGNU M al s o pr ovi des an interface for
Digital flat panels. To ex tend i t s video f unct ional i ty and f l ex i bi l i t y, a
“Video B r i dge” boar d i s also pr ovi ded to s uppor t the NT S C/PAL
Video output. The MAGNU M X GA dr i v er diskettes contain the
Following dr i ver s ;
S iS 630S T VGA dr i ver s for
Windows 95
Windows 98
Windows ME
Windows 2000
Windows NT4.0
Windows XP
Table of contents
Popular Motherboard manuals by other brands

ST
ST STM32L4 Series user manual

eMagin
eMagin SXGA096 user manual

Diamond Systems
Diamond Systems Neptune Specification sheet

Linear Technology
Linear Technology DC1821B manual

Sun Microsystems
Sun Microsystems SPARCengine Ultra AXi Read me first

Texas Instruments
Texas Instruments DRV84 2-EVM Series user guide