Epson Livingstation LS57P2 Owner's manual

About Your Manual
The instructions included with this TV are for your model of the Epson Livingstation, as well
as the other models listed on the cover of the manual.
The instructions refer to an external tuner, which is not included with the LS47P2C or
LS57P2C. Otherwise, they are correct for your TV and describe how to operate it fully.
À propos de votre manuel
La documentation ci-jointe s’applique à votre modèle de téléviseur Epson Livingstation, ainsi
qu’à tous les modèles énumérés sur la couverture du guide.
Les instructions mentionnent un syntoniseur externe qui n’est pas fourni avec les modèles
LS47P2C ou LS57P2C. Autrement, les instructions s’appliquent à votre téléviseur et
expliquent son fonctionnement en détail.
CPD-18886
Printed in USA/Imprimé aux É.-U.
®
HDTV LCD Projection Television
Téléviseur à projection ACL à haute définition

About Your Manual
The manual and setup sheet included in this package are for the following television models:
Although your model number may not appear on the cover of the manual, the instructions
are correct for your TV and describe how to operate it fully.
CPD-18635
Printed in USA
LS47P2 LS57P2
LS47P1D LS57P1D
®
HDTV LCD Projection Television

Selecting a Channel
Follow these steps to select a channel from the Electronic Program Guide (EPG):
1Make sure you are tuned to a digital (High Definition) channel; your tuner does not support the EPG for
non-digital channels.
Note
If you see a message that the EPG is not supported, press the up or down arrow button on your tuner’s remote control to switch to
a digital channel.
2Press the EPG button on the tuner’s remote control twice. You see the Channel Guide.
3Use the up and down arrow buttons on the tuner’s remote control to scroll through the guide. Highlight the
Physical Channel that is on the same row as the Virtual Channel you want.
4Press the Enter button. The image for the first Virtual Channel in the row appears in the preview box in the
upper right corner. (In the screen above, the image from KCET-HD 28-01 is displayed.)
5Press the Exit button on the remote control twice. The screen displays the previewed image.
6To select another Virtual Channel in the same row, press the up arrow button on the tuner’s remote control
until you see the image for the channel you want. To move back to a previous channel in the row, press the
down arrow button.
Note
You can also use the numeric keypad on the tuner or television remote control to select a channel. For instructions on using the
tuner’s remote control to select a channel, see “Selecting Digital Channels” in your tuner’s User’s Guide.
CPD-18867R1
Printed in USA
®
HDTV LCD Projection Television

Installing and Maintaining the Optional
Front Air Filter
Follow these instructions to install and maintain the optional front air filter for your Epson®LivingStation®television.
This filter is intended for customers who live in dry, dusty areas to reduce the amount of dust that enters the TV.
Caution
Once the new air filter has been installed, you need to clean it periodically as described on the next page. Failure to clean the filter
may cause the TV to overheat. If the TV gets too hot, it may turn itself off for protection.
Installing the Filter
Follow these steps to install the new filter:
1Remove the right speaker cover. Grasp the cover and pull it straight off.
2Remove the adhesive backing from the filter.
HDTV LCD Projection Television
®
Remove cover
Remove adhesive backing

3Align the slot in the filter with the tab on the TV. Press the filter in place over the air intake vent.
4Press down on the filter to make sure the adhesive is secure.
5Replace the speaker cover.
Cleaning the Air Filter
Once the air filter is installed, you need to inspect it regularly. If the filter appears to be dirty, clean it as described below.
Note
Whenever you inpect the front air filter, you should also check the air filter on the left side of the TV and clean it if necessary. The
location of this filter is shown in your User’s Guide. You can clean the side filter using the same method that you use to clean the
front filter.
1Remove the right speaker cover.
2If the filter looks dirty, clean it using one of these methods:
• Use a computer vacuum cleaner or the upholstery brush attachment for your home vacuum cleaner to lightly
vacuum the filter and remove the dust. If your home vacuum cleaner has an air bleed valve (located near the
end of the hose where you attach the cleaning tools), you should open the valve to decrease the amount of
suction.
• Use a clean paintbrush with very soft bristles to lightly brush off any dust from the crevices.
3Replace the speaker cover.
Epson and Livingstation are registered trademarks and Epson Exceed Your Vision is a trademark of Seiko Epson Corporation.
© 2007 Epson America, Inc. 7/07 CPD-24509
Align slot with tab on
air intake vent
Make sure adhesive
is secure