ERA Lighting YY-L300 User manual

300W LED Spot Moving Head
User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS

1. Unpacking
Thank you for choosing our 300W LED Spot. For your own safety, please read this manual before
installing the device. This manual covers the important information on installation and applications.
Please install and operate the fixture with following instructions. Meanwhile, please keep this
manual well for future needs.
300W LED Spot is made of a new type of high temperature strength of engineering plastics and
cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following
CE standards, complying with international standard DMX512 protocol. It’s available independently
controlled and linkable with each other for operation. And it is applicable for large-scale live
performances, theater, studio, nightclubs and discos.
4-IN-1 LEDs(RGBW) which features high brightness and stability. Please carefully unpack it
when you receive the fixture and check whether it is damaged during the transportation. And please
check whether the following items are included inside the box:
Moving Head---------One Signal Cable----One
Hanging Bracket-----Two Power Cable----One
User Manual----One
.1.
9. Maintenance and Cleaning
The following points have to be considered during the inspection:
1. All screws for installing the devices or parts of the device have to be tightly connected and must not
be corroded.
2. There must not be any deformations on the housing, color lenses, fixations and installation spots
(ceiling, suspension, trussing).
3. Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4. The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled
installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to
the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to
accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure that the
circuit contacts are in good condition, prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use
alcohol or solvents.There are no serviceable parts inside the device. Please refer to the instructions
under “Installation instructions”.Should you need any spare parts, please order genuine parts from
your local dealer
.10.

8. Key Features
Voltage: 100-240V, 50-60Hz
Power : 450W
Light Source: 300W White LED
Color Temperature: 6800K
LED Life Time: 50000 Hours
Pan: 540 degree+fine
Tilt: 270 degree+fine
Beam Angle: 16 degree
Channel: 14/16 two Channels mode
Dimmer：0-100% smooth linear dimmer
Strobe: 1-25Hz, with pulse effect
Color Wheel: 8 colors+open, with rainbow effect
Gobo Wheel: 8 gobes+open, with rotation and running water effect
Prism: 3 and 5 facet rotation prism and linear prism
Screen: Colorful Screen with Chinese and English, Can adjust 180 degree to fit different installation
position.
Cooling system: With 6pcs highly effective copper pipe to protect the LED
Fixture Dimension: 300*200*490 mm
Package Dimension: 130*380*530 mm
Net Weight: 12KG
Gross Weight: 14KG
.9.
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do not switch
it on immediately. The arising condensation could damage the device. Leave the device switched off
until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for
smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
.2.

3.Operation Instructions
-The 300W LED Spot is for spot lights purpose.
-Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So make sure
to operate the fixture until it is in normal temperature.
-This light should be keep away from strong shaking during any transportation or movement.
-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
-Don’t expose the fixture in overheat, moisture or environment with too much dust when installing
it.
And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the fixture.
-Make sure to put the safety chain and check whether the screws are screwed properly when
installing the fixture.
-Make sure the lens are in good condition. It’s recommended to replace the units if there are any
damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the fixtures without any instruction by the manufacturer or the appointed
repairing agencies.
-It is not in warranty range if there are any malfunctions from not following the user manual to
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
4. Mounting and Installation
Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas,
or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
.3.
16 Channels mode:
CH
Function
DMX
Value
Description
1
Pan
0-255
0-540 degree
2
Pan Fine
0-255
16 bit
3
Tilt
0-255
0-270 degree
4
Tilt Fine
0-255
16 bit
5
Pan/Tilt Speed
0-255
Speed from fast to slow
6
Dimmer
0-4
No function
5-255
0-100% Linear dimmer from dark to bright
7
Strobe
0-3
No function
4-95
Strobe with the same step from slow to fast
96-176
Random Strobe
177-255
Thunder Strobe
8
Color Wheel
0-127
Color wheel continuous rotation
128-189
Color change
190-220
Clock-wise rotation from slow to fast
221-224
No function
225-255
Anti-clockwise rotation from slow to fast
9
Gobo Wheel
0-4
Open
5-25
Gobo change (Each 3 DMX value is a gobo)
26-31
Open
32-52
Gobo rotation (Each 3 DMX value is a gobo)
53-59
Open
60-115
Gobo shaking (Each 7 DMX value is a gobo)
116-129
Open
130-185
Gobo shaking (Each 7 DMX value is a gobo)
186-202
Open
203-227
Gobo wheel clockwise rotation from slow to fast
228-229
Stop rotation
230-225
Gobo wheel anti-clockwise rotation from slow to fast
10
Gobo Rotation
0
No Function
1-124
Clockwise gobo wheel rotation
125-132
No Function
133-255
Anti-Clockwise gobo wheel rotation
11
Focus
0-255
Focus
12
Prism
0-31
No prism
32-63
Prism 1
64-95
Prism 2
96-127
Prism 3
128-255
Prism rotation from slow to fast
13
Prism rotation
0
No Function
1-124
Clockwise prism rotation
125-132
No Function
133-255
Anti-Clockwise prism rotation
14
Marco Effect
0-255
Marc effect show
15
Auto Run and
Sound Activated
0-19
No function
20-99
Auto Run
100-199
Sound Activated
200-255
No function
16
Reset
0-199
No function
200-255
Reset in 5 seconds
.8.

Never stand directly below the device when mounting, removing, or servicing the fixture from a
periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main power cord to
the appropriate wall outlet.
Clamp Mounting: 300W LED Spot provides a unique mounting bracket assembly that integrates the
bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one unit (see
the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated
clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega
bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to
the fixture using on of the safety cable rigging point integrated in the base assembly
Regardless of the rigging option you choose for your 300W LED Spot, always be sure to secure your
fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging
bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and
never secure a safety cable to a carrying handle.
.4.
7. DMX Channels
14 Channels mode:
CH
Function
DMX
Value
Description
1
Pan
0-255
0-540 degree
2
Pan Fine
0-255
16 bit
3
Tilt
0-255
0-270 degree
4
Tilt Fine
0-255
16 bit
5
Pan/Tilt Speed
0-255
Speed from fast to slow
6
Dimmer
0-4
No function
5-255
0-100% Linear dimmer from dark to bright
7
Strobe
0-3
No function
4-95
Strobe with the same step from slow to fast
96-176
Random Strobe
177-255
Thunder Strobe
8
Color Wheel
0-127
Color wheel continuous rotation
128-189
Color change
190-220
Clock-wise rotation from slow to fast
221-224
No function
225-255
Anti-clockwise rotation from slow to fast
9
Gobo Wheel
0-4
Open
5-25
Gobo change (Each 3 DMX value is a gobo)
26-31
Open
32-52
Gobo rotation (Each 3 DMX value is a gobo)
53-59
Open
60-115
Gobo shaking (Each 7 DMX value is a gobo)
116-129
Open
130-185
Gobo shaking (Each 7 DMX value is a gobo)
186-202
Open
203-227
Gobo wheel clockwise rotation from slow to fast
228-229
Stop rotation
230-225
Gobo wheel anti-clockwise rotation from slow to fast
10
Gobo Rotation
0
No Function
1-124
Clockwise gobo wheel rotation
125-132
No Function
133-255
Anti-Clockwise gobo wheel rotation
11
Focus
0-255
Focus
12
Prism
0-31
No prism
32-63
Prism 1
64-95
Prism 2
96-127
Prism 3
128-255
Prism rotation from slow to fast
13
Prism rotation
0
No Function
1-124
Clockwise prism rotation
125-132
No Function
133-255
Anti-Clockwise prism rotation
14
Reset
0-199
No function
200-255
Reset in 5 seconds
.7.

5. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to
the male 3-pin XLR input of the moving head. You can chain multiple
Moving heads be connected together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption
of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω
resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last
fixture in the chain. Please see illustrations below.
.5.
1
2
3
PI N 3
PI N 2
120 Ω
6. Menu Operations
MENU
Address 1-512
Chin
Engh
Norm
RunMode
Language
Display
ChanMode
DMX Clear
Xreverse
Yreverse
XY Fback
Return
Reve
14CH
16CH
DMX
Musc
Auto
Off
On
Off
On
On
Off
▲
Pan
Tilt
Gobo
Gobo Auto
Colour
Focus
Prism
PrismRot
00-40
00-40
Yes
No
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
SYS Set
Rectify
ChanLevel
Control
Reset
ExitMenu ▲
Off
On
Language setting
Display turn up 180
degree setting
Channel mode
setting
Run mode setting
DMX Signal clear
Pan Invert setting
Tilt Invert setting
Pan/Tilt sensor
detection
Return to menu
Adjust the
Default position
of these parts
DMX value of
each channel
Manual control of
each channel
.6.